Luxury F5151S Decoration Ceiling Fan Instruction Manual

: June 5, 2024
: Luxury

Table of Contents

Basic parameters
Precautions
Prepare tools before installation
Ceiling Fan Kit Package List
Fan installation procedures
Balance adjustment method of ceiling fan.
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Luxury F5151S Decoration Ceiling Fan

Basic parameters

Voltage: 110V-230V (60HZ-S0HZ)
Power: Mwer: 35W; LED power: 36W
Wind speed+ Color change: 6 wind speed+3 color temperatures(Cool white light 6S00K+ warm light 3000K+ neutral light 4500K)
Number of rotating leaves: 5 blades
Color: Black/White
Fan blade material: ABS
Motor material: Pure copper wire winding and high-quality silicon steel stator, high efficiency, super quiet, energy saving, durable.
Control method: Remote control
Diameter: 42/46 inch
Reversible : YES
Use area: 10ft2-15ft2

Precautions

Before using this ceiling fan light, please read this manual carefully and operate strictly in accordance with the procedures.

The input voltage of this product: 110V/60Hz~230V50Hz.
If you have insufficient knowledge of electrical appliances, be sure to hire an experienced expert to install them.
Before installing and disassembling the ceiling fan light, please turn off the power first. The installation must be installed in the order of ground wire, live wire, and neutral wire. Before disassembly, it must be disassembled in the order of neutral wire, live wire and ground wire to avoid electric shock.
The ceiling fan must be installed on a solid ceiling, and the location of the ceiling fan must be able to withstand a gravity greater than 60 KG.
When installing the ceiling fan, all screws must be securely locked.
When the ceiling fan is rotating, no objects should touch the blades to avoid danger.
The angle and elevation of the leaf frame are determined after many repeated measurements, so it cannot be changed at will. When installing the leaf frame and blades, special care should be taken not to force collisions. If the angle and elevation angle of the leaf frame are deformed that will cause the ceiling fan to shake.

Prepare tools before installation

Ceiling Fan Kit Package List

Ceiling Fan Kit
Before the ceiling fan is installed, there are the following accessories in the carton, please check them one by one, if there is no shortage, you can install it.

Fan installation procedures

Secure the ceiling plate
(1) First remove the Ceiling plate from the fan host, (Figure 1) take down the two Fixing screws of the fan host (the removed screws are preserved, not to be discarded),and two screws with key on the fan host are twisted loose, and then Rotate the ceiling plate out counterclockwise.

(2) Install the ceiling plate
a. Concrete ceiling installation: please first use punch drill mounted 8 drill bit,the ceiling plate installation hole corresponding to good flowering, and then use the impact drill on the concrete flowering hole, and then the ceiling plate with M6 explosive screw lock (figure 2).
b. Wooden ceiling mounting: wooden ceilings are drilled with wood-teeth screws to secure the ceiling plate on the wooden side or “corner” (as shown in Figure

Pay attention to the tips!
Depending on the ceiling of different materials, using different screws to secure the ceiling plate please do not directly fix the ceiling plate on the ceiling splint, in order to prevent the wooden teeth screw loose, bring danger, the ceiling plateis fixed, must ensure that can withstand more than 60 kg of gravity (hand-pulled)for safety.

Connect the fan controller
a. Hang the fan host with a steel cable on the hooking of the ceiling plate.( Figure 3)

b. Wiring method of remote control receiver: (Figure 4)
1). Connect the lamp neutral wire (white wire) of the fan host to the No. 1 wiring hole of the remote control receiver (lamp neutral wire, white mark)
2). Connect the lamp live wire (blue wire) of the fan host to the No. 2 wiring hole of the remote control receiver (lamp live wire, blue mark)
3). Connect the motor U wire (gray wire) of the fan host to the No. 3 wiring hole of the remote control receiver (motor U wire, gray mark)
4). Connect the motor V wire (red wire) of the fan host to the No. 4 wiring hole of the remote control receiver (motor V wire, red mark)
5). Connect the motor W wire (yellow wire) of the fan host to the No. 5 wiring hole of the remote control receiver (motor W wire, yellow mark)

Connect the home live wire on the ceiling to the L wiring hole of the remote control receiver (input the firewire logo)
7). Connect the household neutral wire on the ceiling to the N wiring hole of the remote control receiver (input the neutral line logo)
8). After the remote control receiver is connected, please put the remote control receiver into the bell of the fan host.

Install the fan host
a. Match the two keyholes of the fan host to the two fixing screws of fan host on the ceiling plate, and then turn the fan host clockwise on the ceiling plate.
( Figure 5)

b. Align the two fixing screws of the fan host that have just been twisted to the holes, then tighten them, and tighten the remaining fixing screws in turn (Figure 6).
Install fan blades
a. Twist off the blade fixing screws on the fan host, keep them, and do not discard them. (As shown in Figure 7)

b. Match the fan blade holes to the screw holes on the fan host, and tighten the fan blade fixing screws that have just been twisted (Figure 8). Five fan blades.
Install the lamp panel
a.Twist off the fixing screws of the lamp panel on the fan host, keep them, and do not discard them.
b.Match the fixing screw hole of the lamp panel to the fixing screw hole of the lamp panel on the fan host, and tighten the fixing screw of lamp panel, which has just been twisted off. ( Figure 10)
Install the light source
a. The light source is absorbed in the lamp panel. ( Figure 11)
b. Connect the live wire of the lamp on the fan host to the live wire of the lamp on the light source with the wiring terminal, and connect the neutral wire of the lamp on the fan host to the neutral wire of the lamp on the light source with the wiring terminal (Figure 12)
c. Insert the two connected wiring terminals into the light source hole, so as not to affect the light effect. (Figure 13)
Install the lampshade
a. Please place the acrylic sheet on the lamp panel at a certain angle (Figure 14), and then lay it flat
b. The effect of fan installation. ( Figure 15)

Balance adjustment method of ceiling fan.

If there is any shaking after ceiling fan installation, please confirm whether the screws that fix the drop ball, mounting bracket, hanger, leaf shelf, and blade are locked. If one of the above parts is not locked, please re-lock it.
If it is locked, please adjust it as follows.

Change the position of the fan blades:
a. As shown in the figure 1 on the right, please remove the leaf and 2 and lock each other to observe the effect.
b. There is no improvement after the swap blades position. Please remove the fan blades 2 and 3 and re-lock each other to observe the effect.
Adjust with balance pack
a. Take out the balance bag from the packing box, use a balance clamp to select one of the fan blades and clamp the balance clamp on the edge of the tail end of the fan blade (as shown in Figure 2 on the ri9ht)
b. Turn on the fan switch to see wnether the shaking of the ceiling fan has been reduced. If it does not improve, try another fan blade. Experiment with all the fan blades in turn to find the blade with the weakest clamping balance.
c. Clamp the balance clamp on the fan blade with the weakest shaking, move it in or out on the edge of the fan blade, turn on the ceiling fan to find the best position of the balance clamp to control the shaking balance (as shown in the right Figure 16)
d. Take the balance sticker, tear off the double-sided tape of the balance sticker, and stick the balance sticker on the center of the blade at the position of the balance clip (as shown in the right Figure 17)