SATCO S11568 Starfish Smart Wifi LED Retrofit Downlights Instruction Manual
- June 13, 2024
- SATCO
Table of Contents
Satco Products, Inc.
Brentwood, NY 11717 STARFISH™ SMART WIFI LED RETROFIT DOWNLIGHTS
Model: S11568, S11569, S11570, S11571
INSTALLATION AND SAFETY INSTRUCTIONS
IMPORTANT: Read before installing fixture. Retain for future reference.
WARNING: Risk of Fire or Electric Shock
- LED Retrofit Kit installation requires knowledge of luminaries electrical systems. If not qualified, do not attempt installation. Contact a qualified electrician.
- To reduce risk of fire and over-heating, secure all connections.
- TURN OFF the electrical power before proceeding.
- Install this kit only in luminaires that have the construction features and dimensions shown in the photographs and/or drawings and where the input rating of the retrofit kit does not exceed the input rating of the luminaire.
- The electrical rating of this product is 120V/60Hz.
- To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.
- Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation.
- This retrofit kit is accepted as a component of a luminaire where the suitability of the combination shall be determined by authorities having jurisdiction.
- This device is not intended for use with emergency exits.
- Suitable for wet locations, covered ceiling-mounted luminaire.
INSTALLATION
STEP 1: Turn OFF power prior to installation.
STEP 2: Remove existing trim installed in recessed housing (if
necessary).
STEP 3: If applicable, slide lamp holder bracket to its upward maximum
position. If the lamp holder bracket is less than 4 1/2″ from the bottom edge
of the fixture enclosure, the lamp holder bracket must be removed.
STEP 4: If necessary, remove the lamp holder mounting bracket and the
lamp holder from the bracket, then attach the provided label to the existing
luminaire. See Figure A.
STEP 5: Install adapter into socket. See Figure B.
STEP 6: Connect the orange terminals together. See Figure C.
STEP 7: To install the 4″ downlight, slide the downlight up into the
recessed housing. Push the trim until the outer edge is flush with the ceiling
surface. See Figures D & F.
STEP 8: To install the 5″/6″ downlight, insert torsion springs into
luminaire housing brackets. Gently push up trim and slide the LED downlight up
into the recessed housing until the trim is flush with the ceiling. See
Figures E & F.
STEP 9: Installation is complete. Turn power ON.
STEP 10: App Connection: To connect your device, download the free
“Starfish Smart Lighting” App from the app store. Please refer to our Starfish
User Guide for detailed instructions on how to pair your device.
For Installation into existing recessed LED luminaire with compatible
connectors:
-
Follow STEPS 1 and 2 above.
STEP 3: Discard medium base adapter. -
Skip STEPS 4 and 5 above. Continue with STEPS 6 – 9 above.
https://smartapp.tuya.com/satcosmart
SYSTEM REQUIREMENTS
- Minimum iOS 9.3 or Wi-Fi 4.4
- Dedicated 2.4GHz Wi-Fi Network
TECHINCAL SUPPORT
support@satcostarfish.com
-
DOWNLOAD THE STARFISH APP
https://smartapp.tuya.com/satcosmart
(App design is subject to change without notice.)
REGISTER YOUR ACCOUNT
Verify you’re connected to a 2.4GHz Wi-Fi Network. -
Launch the STARFISH app and tap “Sign-up” to create a new account or “Login” to your existing account.
-
Enter email address, then select “Get verification code”.
-
Enter verification code that was sent to your email.
-
Tap the “Me” button at the bottom of the screen, and then “Home Management”. Select the “Create a home” button to set up your home.
ADD A DEVICE -
Tap the ( +) button on the top right corner to access the action menu, then select “Add Device”.
-
Select device type from the listed categories.
It is recommended to pair 8 or fewer devices at 1 time. If you are pairing multiple devices at one time, and some of the devices do not pair the 1st time; repeat the pairing process.
PAIR ADEVICE WITH WI-FI -
Turn your device on. The device should liil automatically enter pairing mode. If it does not start blinking rapidly after 7 -1 O seconds then turn your device off/on 5 times to enter pairing mode. Confirm that the device is blinking quickly and click· “next”.
This device has advanced pairing retention technology. The device(s) that already paired will remain paired to the network, the device(s) that did not pair will return to pairing mode. To reset to factory settings, turn the switch off /on Bx. -
A Select your 2.4GHz Wi-Fi Network name and enter password then click “Next.”
The pairing status screen will appear.
PAIR A DEVICE WITH WI-FI/BLUETOOTH
Note: Verify your mobile device is connected to a 2.4GHz Wi-Fi Network and
that you have Bluetooth turned ON for connection. For Wi-Fi/Bluetooth enabled
liil devices, you will see a pop-up indicating that there are unpaired devices
in the area.
The device does not need to be in pairing mode. Tap “Add” and select the
devices you would like to connect.
9B Once all the
devices have liiil connected , tap “Next”.
Once device is successfully
paired, continue to step 10.
When successfully connected , you may rename the device. Tap the “Pen” icon,
enter the new name and select “Done”. The device is now ready to be control
led with the STARFISH app.
Note: If pairing is unsuccessful, please refer to the FAQs on
Satco.com/Starfish
Bluetooth is strictly used to pair and connect the device. A 2.4GHz Wi-Fi
Network is required to operate all STARFISH products.
From the Home Management screen , select the Home that you would like to
share. Tap “Add Member” and select the way that you would like to send the
invitation
Enter the
user information and select if the new member will be an “Administrator” or a
“Common Member” in the Home. Tap “Save” to send the invitation.
To view the entire STARFISH product line visit Satco.com/STARFISH
Scan QR Code to learn more
www.satco.com/starfish
General
| Status | Active |
|---|---|
| Fnish | White |
| Wattage | 13W |
| Style | Utirrty |
| CCT (Kelvin) | 2000K-5000K |
| Color Temperature | Warm to Cool White‘Cobr Changeable |
| Width (n.) | 7. |
| Height (n.) | 3. |
| Indoor or Outdoor Fixture | Indoor |
Smart Product Info
| IOT Enabled | Yes |
|---|---|
| Voice Assistants Supported | Google Home;Alexa;Siri;SmartThings |
Specifications
| Technology | LED |
|---|---|
| CRI | 90 |
| Lumen Output | 850L |
| Rated Hours | 50000 |
| Voltage | 120V |
| Dimmable | Yes-Dimmable |
| Dimming Note | Only with Starfish App |
| Beam Angle | 110 |
| Operating Temperature | -20C (-49 to +40C (+1049 |
| IC Rated | Yes |
| Weight (lb.) | 0.57 |
| Fixture Shape | Round |
| Fixture Material | Aluminum |
| Fixture Type | Dovmlight Retrofit |
Compliance
| Safety Listing | cETLus |
|---|---|
| Location Rating | Wet |
| Energy Star | Yes |
| ES Unique ID | ESID-2495004 |
| Air Tight Rated | Yes |
| CA T20 / T24 Rationale | California T24 2016 – 2022 JAListed |
| California Status | Lawful for sale in California |
| Title 20 / 24 Status | California T24 Listed |
| California Prop 65 | Lead |
| RoHS Compliant | Yes |
| FCC Compliant | Yes |
| SDS Sheet | LED_Fixture |
Additional Information
| Includes | E26 Adapter included (S9001) |
|---|---|
| Warranty | 5 Year Limited – Fixtures |
Copyright 2020 Satco Products, Inc.All Rights Reserved
For More Information Visit:http://www.satco.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>