BS Battery BS 10 Smart Battery Charger and Maintainer Lithium Instruction Manual
- June 6, 2024
- BS BATTERY
Table of Contents
BS Battery BS 10 Smart Battery Charger and Maintainer Lithium
Product Information
Specifications:
- Type: SLA & SLA MAX Batteries
- Usage: Factory Activated and Sealed Maintenance Free Battery
- Brand: BS Battery
- Website: www.bs-battery.com
Product Usage Instructions
Safety Warnings:
- Wear eye protection.
- Keep children away from acid and batteries.
- Avoid fire, sparks, naked lights, and smoking.
- Corrosive hazard: Battery acid is highly corrosive, wear protective gloves and eye protection.
- Warning note: Do not expose batteries to direct sunlight without protection. Store in a frost-free area.
- Dispose of old batteries properly, do not throw them in domestic waste bins.
Fitting:
- (A) To optimize battery life and power, an initial charge is recommended.
- (B) Always follow the vehicle manufacturer’s directions for fitting.
- (C) Connect Positive and Negative terminals to their respective terminals.
Charging:
Follow the manufacturer’s instructions for charging the battery safely and effectively.
Maintenance:
Regularly check the battery for any signs of damage or corrosion. Keep the terminals clean and tight. Refer to the manual for specific maintenance guidelines.
FAQ (Frequently Asked Questions)
-
Q: Can I expose the battery to direct sunlight?
A: No, do not expose the battery to direct sunlight without protection to avoid damage. -
Q: How should I dispose of old batteries?
A: Take old batteries to a proper collection point; do not dispose of them in domestic waste bins. -
Q: Is an initial charge necessary for the battery?
A: An initial charge is highly recommended to optimize the life and power of your battery.
INSTRUCTIONS
INSTRUCTIONS FOR USE AND CARE OF FACTORY-ACTIVATED AND SEALED MAINTENANCE FREE BATTERY
- Please read the instructions carefully before using the battery.
- The brand could not be held responsible for the consequences of improper installation and/or misuse of the battery inside your vehicle. If you have any problem or doubt, for your security we recommend you to contact a professional.
- Instructions must be followed for a safe use of Factory Activated and Sealed Maintenance Free batteries.
- Wear eye protection.
- Keep children away from acid and batteries.
- Explosion hazard:
- A highly-explosive oxyhydrogen gas mixture occurs when charging batteries.
- Fire, sparks, naked lights and smoking are prohibited:
- Avoid causing sparks when dealing with cables and electrical equipment and beware of electrostatic discharges.
- Avoid short-circuits.
- Corrosive hazard:
- Battery acid is highly corrosive:
- Wear protective gloves and eye protection.
- First aid:
- EYES > Immediately hold eyes open and rinse immediately with plain water for at least 15 minutes. Consult a doctor without delay.
- SKIN > Quickly, but gently, wipe acid from skin. Remove any contaminated clothing or footwear and thoroughly wash the affected area with soap and water for at least 15 minutes. Consult a doctor without delay.
- SWALLOWED > Do not induce vomiting. Rinse out mouth with water, and if conscious, induce copious drinking of water or milk. Consult a doctor without delay.
- Warning note:
- Do not expose batteries in direct daylight without protection.
- Discharged batteries can freeze, therefore it must be stored in an area free from frost.
- Disposal:
- Take old batteries to a proper collection point.
- The instructions listed under part 1 must be followed during transportation.
- Never dispose old batteries in a domestic waste bin.
INFORMATION
- (A) This battery is a fully charged and sealed Factory Activated product, integrating a venting valve. It contains non-floating electrolyte and any gas produced during use is fully absorbed within the battery, ensuring that this battery is totally Free.
- (B) As this battery was fully activated at the factory, the voltage must be maintained at all times, which requires a maintenance charge to be performed every 12 weeks (or if the voltage is less than 12.4 volts) until the battery is put into service. Failure to do so will reduce the life of this battery and may render it unserviceable.
- (C) As this battery is ready to use, care must be taken to avoid a short circuit between the positive and negative terminals.
- (D) Under no circumstances must the Factory Fitted Sealing Plugs be removed.
- (E) The Venting Valve Opening must not be blocked.
FITTING
- (A) To optimize the life and power of your battery, an initial charge is highly recommended.
- (B) Always fit by the vehicle manufacturer’s directions.
- (C) Positive and Negative terminals must be connected to their correct terminals.
CHARGING
- (A) Never exceed a charging current greater than 50% of the battery capacity. Charging too quickly or overcharging can cause damage.
- (B) If the battery becomes hot to the touch, stop the charging and allow it to cool down before recharging.
- (C) Always remove the battery from the vehicle before charging.
- (D) Charge the battery with a Motorcycle battery charger suitable for this size/type of battery with an output power of 1/10th of the battery’s rated capacity.
- (E) Let the battery settle for 1 or 2 hours after charging before checking the voltage. If the voltage is less than 12.8 volts, an additional charge is necessary.
MAINTENANCE
- (A) As this battery is fully sealed and activated at the factory, there is no maintenance by way of topping up fluid levels. This is the reason why one must never attempt to open this battery.
- (B) If this battery has not been used for a quite long time, check the voltage and recharge as required and described in the ’’Charging’’ section.
- (C) As some fitted equipment draws current even when the vehicle is not being used, the battery may require a charge even after a relatively short period of inactivity.
- (D) Keep the connecting poles clean and securely fastened.
FIND THE RIGHT BS BATTERY FOR YOUR VEHICLE
WITH BS BATTERY FINDER
COMPATIBLE BATTERY CHARGERS
SMART BATTERY CHARGER & MAINTAINER 6V/12V – 1A For Lead Acid & Lithium Battery size: up to 20Ah (40Ah in maintenance)
- Auto-detect Lead Acid or Lithium technology
- 6V & 12V mode selection
- Zero overcharges: adaptable charging algorithm Lead Acid & Lithium (LiFePO4)
- Safe: connection spark-free, reverse polarity, short circuit and internal overheat protection
- Easy to use: connect, select battery voltage & forget
SMART BATTERY CHARGER & MAINTAINER 12V – 1.5A WITH RECONDITIONING FUNCTION For Lead Acid Battery size: up to 30Ah (60Ah in maintenance)
- Reconditioning function for deeply discharged batteries
- Ideal for charging during the winter season
- Safe: connection spark-free, reverse polarity, short circuit and internal overheat protection
- Easy to use: connect & forget
- Multiaxis hook
SMART BATTERY CHARGER & MAINTAINER 12V – 3A For Lead Acid & Lithium Battery size: up to 60Ah (80Ah in maintenance)
- Auto-detect Lead Acid or Lithium technology
- Zero overcharges: adaptable charging algorithm Lead Acid & Lithium (LiFePO4)
- Safe: connection spark-free, reverse polarity, short circuit and internal overheat protection
- Easy to use: connect & forget
- Multiaxis hook
SMART BATTERY CHARGER & MAINTAINER 12V – 1/4/6A WITH RECONDITIONNING FUNCTIONFor Lead Acid Battery size: up to 120Ah (180Ah in maintenance)
- Reconditioning function for deeply discharged batteries
- Selectable battery type (Calcium, Gel, AGM) and charge rate (1A/4A/6A)
- Automatic battery condition diagnosis
- Safe: connection spark-free, reverse polarity, short circuit and internal overheat protection
- Easy to use: connect, select battery type charge rate & forget
The Power You need
Documents / Resources
| BS
Battery BS 10 Smart Battery Charger and Maintainer
Lithium
[pdf] Instruction Manual
BS 10 Smart Battery Charger and Maintainer Lithium, BS 10, Smart Battery
Charger and Maintainer Lithium, Battery Charger and Maintainer Lithium,
Charger and Maintainer Lithium, Maintainer Lithium, Lithium
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>