BS BATTERY 2022-07 Lithium Battery Instruction Manual

BS BATTERY 2022-07 Lithium Battery

 MOTORCYCLES BATTERY MF & CHARGING INSTRUCTIONS

WARNING

Please read the instructions carefully before using the battery.
The brand could not be held responsible for the consequences of improper installation and/or misuse of the battery inside your vehicle. If you have any problem or doubt, for your security we recommend you to contact a professional.

• Instructions must be followed for a safe use of Factory Activated and Sealed Maintenance Free batteries.
• Wear eye protection.
• Keep children away from acid and batteries.
• Explosion hazard:
  • A highly-explosive oxyhydrogen gas mixture occurs when charging batteries.
• Fire, sparks, naked lights and smoking are prohibited:
  • Avoid causing sparks when dealing with cables and electrical equipment and beware of electrostatic discharges.
  • Avoid short-circuits.
• Corrosive hazard:
  • Battery acid is highly corrosive:
  • Wear protective gloves and eye protection.
  • Do not tilt battery, acid can escape from the degassing openings or vents.
• First aid:
  • EYES > Immediately hold eyes open and rinse immediately with plain water for at least 15 minutes. Consult a doctor without delay.
  • SKIN > Quickly, but gently, wipe acid from skin. Remove any contaminated clothing or footwear and thoroughly wash the affected area with soap and water for at least 15 minutes. Consult a doctor without delay.
  • SWALLOWED > Do not induce vomiting. Rinse out mouth with water, and if conscious, induce copious drinking of water or milk. Consult a doctor without delay.
• Warning note:
  • Do not expose batteries in direct daylight without protection.
  • Discharged batteries can freeze, therefore it must be stored in an area free from frost.
• Disposal:
  • Take old batteries to a proper collection point.
  • The instructions listed under part 1 must be followed during transportation.
  • Never dispose old batteries in a domestic waste bin.

HOW TO ADD THE ELECTROLYTE

PRECAUTIONS
Always remove the battery from the vehicle.
Make sure the electrolyte is as specified for your battery.
PREPARING THE ELECTROLYTE
Let the battery stand on a level surface. Remove the sealing sheet.

PREPARING THE ELECTROLYTE
Take the electrolyte container out of the vinyl bag. Detach the strip cap plug from the container, which will be used as the battery plugs later.
Note: Do not peel or pierce the sealed areas.

PROCEDURE FOR FILLING BATTERY WITH ACID
Place the electrolyte container upside down with the 6 sealed areas in line with the 6 filler ports of the battery. Push the container down strongly enough to break the seals. Air bubbles should come up from ports.
Note: Do not tilt the container as the electrolyte flow may be interrupted.

CHECKING THE ELECTROLYTE FLOW
Make sure air bubbles are coming up as stated in slep 3 above. Leave the container in this state for 20 minutes or longer.
Note: If there is no air bubbles coming up from the filler ports, tap the bottom of the container two or three times. Never remove the container from the battery. Never cut the joints with nippers or the like.

PULLING OUT THE CONTAINER
Be certain that all the electrolyte has flowed out. Tap the bottom in the same way as step 4 if there is any electrolyte left in the container. Now pull the container gently out of the battery.

SEALING THE BATTERY
Fit the strip cap plug tightly into the filler ports. Make sure the strip is at the same level as the top of the battery. The fill-up is now complete. Never remove the caps, no add any water or electrolyte.

IMPORTANT INFORMATION

• This battery is a fully charged and sealed before first use, integrating a venting valve. It contains non-floating electrolyte and any gas produced during use is fully absorbed within the battery, ensuring that this battery is totally Maintenance Free.
• As this battery was activated before installation, it is essential that the battery stands upright during minimum 60 minutes before installation on the vehicle. This allows the electrolyte to permeate into internal materials.
• Under no circumstances should the Sealing Plug be removed.
• The Venting Valve Opening must not be obstructed.

FITTING

•  In order to optimize the life and power of your battery, an initial charge is highly recommended. (refer to ’’Charging’’ section)
• Always fit in accordance with vehicle manufacturer’s directions.
• Positive and Negative terminals must be connected to their correct terminals.

CHARGING

• Never exceed a charging current greater than 50% of the battery capacity. Charging too quickly or overcharging can cause damages.
• If the battery becomes hot to the touch, stop the charging and allow it to cool down before recharging.
• Always remove the battery from the vehicle prior to charging.
• Charge the battery with a Motorcycle battery charger that suits for this size/type of battery with an output current of 1/10th of the battery’s rated capacity.
• Let the battery settle for 1 or 2 hours after charging and before checking the voltage. If the voltage is less than 12.8 volts, an additional charge is necessary.

MAINTENANCE

• As this battery is fully sealed and activated at the factory, there is no maintenance by way of topping up fluid levels. This is the reason why one must never attempt to open this battery.
• If this battery has not been used for a quite long time, check the voltage and recharge as required and described in the ’’Charging’’ section.
• As some fitted equipment draws current even when the vehicle is not being used, the battery may require a charge even after a relatively short period of inactivity.
• Keep the connecting poles clean and securely fastened.

COMPATIBLE BATTERY CHARGERS

SMART BATTERY CHARGER & MAINTAINER WITH RECONDITIONNING FUNCTION For Lead Acid Battery size: up to 120Ah (180Ah in maintenance)

12V – 1/4 /6A

• Automatic battery charger & maintainer
• Safe: connection spark free, reverse polarity, short circuit and internal overheat protection
• Easy to use: connect & forget
• Battery thermal runaway protection
• Ideal for charging during winter season

SMART BATTERY CHARGER & MAINTAINER For Lead Acid & Lithium

Battery size: up to 60Ah (80Ah in maintenance)

12V – 3A

• Automatic battery charger & maintainer
• Auto detect Lead Acid or Lithium technology
• Adaptable charging algorithm for Lead Acid & Lithium (LiFePO4)
• Safe: connection spark free, reverse polarity, short circuit and internal overheat protection
• Easy to use: connect & forget
• Multiaxis hook

SMART BATTERY CHARGER & MAINTAINER WITH RECONDITIONNING FUNCTION For Lead Acid
Battery size: up to 30Ah (60Ah in maintenance)

12V – 1.5 A

• Smart battery charger & maintainer with reconditioning function
• Multiaxis hook
• Ideal for charging during winter season
• Safe: connection spark free. Reverse polarity, short circuit and internal overheat protection
• Easy to use: connect & forget

SMART BATTERY CHARGER & MAINTAINER For Lead Acid & Lithium
Battery size: up to 20Ah (40Ah in maintenance)

6V/12V – 1A

• Automatic battery charger & maintainer
• Auto detect Lead Acid or Lithium technology
• Adaptable charging algorithm for Lead Acid & Lithium (LiFePO4)
• Safe: connection spark free, reverse polarity, short circuit and internal overheat protection
• Easy to use: connect & forget
• 6V & 12V manual switch selection

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>