BS BATTERY PB-02 Power Box Instruction Manual

June 9, 2024
BS BATTERY

BS-BATTERY-PB-02-Power-Box-LOGO

BS BATTERY PB-02 Power Box

POWER BOX- BOX CONTENT

  • 1x Power Box
    BS-BATTERY-PB-02-Power-Box-01

  • 1x Booster case

  • 1x Jump start cable

  • 1x Multi USB cable (type C, Micro USB, lightning)

  • 1x Home charger

  • 1x Car adaptor

User manual for POWERBOX PB-02

THIS MANUAL CONTAINS IMPORTANT SAFETY AND OPERATING INSTRUCTIONS

The POWERBOX PB-02 can start engine equipped with Lead Acid batteries only. It is not recommended for lithium batteries.

PRODUCT LAYOUT

BS-BATTERY-PB-02-Power-Box-08

WARNING
This manual includes guidelines on the operation of your device and the precautions to follow for your own safety. Ensure it is read carefully before first use and keep it handy for future reference. This device should only be used for start-up and / or power supply within the limits indicated on the device and in the manual. The safety instructions must be followed. In case of improper or unsafe use, the manufacturer cannot be held responsible.

This device may be used by children from age 8 and by persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge, provided that they are under supervision or have been told how to use the device safely and are aware of the potential risks. Children must not use the device as a plaything. Cleaning and servicing tasks may not be carried out by children unless they are supervised.

  • Do not use for charging non-rechargeable batteries
  • Do not operate the device with a damaged power supply cord or a damaged mains plug.
  • Do not use any charger other than the one supplied with the machine to charge the batteries.
  • Do not use the device if the charging cable appears to be damaged or assembled incorrectly in order to avoid any risk of short circuiting the battery (Power Box charger).
  • Never charge a frozen or damaged battery.
  • Do not cover the device. Do not place the device near a fire or subject it to heat or to longterm temperatures exceeding 50°C.
  • Risk of explosion or acid projection if the clamps are shortcircuited or if the 12V booster is connected to a 24V vehicle or vice versa.
  • The automatic mode of operation and usage restrictions are explained below in these operating instructions.

RISK OF EXPLOSION AND FIRE!
A battery being charged can emit explosive gas.

  • Avoid flames and sparks. Do not smoke.
  • Protect the electrical contacts of the battery against short-circuiting.

ACID PROJECTION HAZARD!

  • Wear safety goggles and protective gloves.
  • If your eyes or skin come into contact with battery acid, rinse the affected part of the body with plenty of water and seek immediate medical assistance.

CONNECTION / DISCONNECTION

  • Disconnect the power supply before connecting/disconnecting the device to/from the battery.
  • The terminal of the battery that is not connected to the car frame must be connected first. The other connection must be made on the car frame, far from the battery and the fuel line.
  • After the start-up operation, disconnect the booster. First remove the chassis connection and then the battery connection, in the order shown.

ENTRETIEN

  • The power supply cable cannot be replaced. If the cable is damaged, the device should not be used. Service should be performed by a qualified person.
  • Warning! Always remove the power plug from the wall socket before carrying out any work on the device. Under no circumstances should solvents or other aggressive cleaning agents be used.
  • Clean the device’s surfaces with a soft, dry cloth.

REGULATIONS

  • The device complies with European Directive.
  • EAC conformity mark (Eurasian Economic Commission).
  • Equipment in compliance with British requirements.
DISPOSAL
  • This product should be disposed of at an appropriate recycling facility. Do not dispose of in domestic waste.
  • The battery must be removed from the device before the latter is discarded.
  • The battery must be dropped off at a suitable recycling facility.
  • The device must absolutely be disconnected from the power supply network before removing the battery.

MAIN FEATURES

  • Compact & powerful lithium booster rated at 600A (1200A peak current)
  • Up to 20 jump starts in one charge
  • Designed for gas and diesel engines
  • Very safe: Smart cable with spark-proof connection and reverse polarity protection
  • Power supply for small electronic devices via their USB ports. Most of smartphones, earphone, portable gaming devices, MP3/MP4 players can be charged with the included accessories
  • LED flashlight function with 3 modes
  • LED display with battery state of charge indication and output port used

Extreme outside temperatures or mechanical problems on the vehicle (poor starter, no fuel or engine problems) can limit the booster’s capacity.

OPERATION

  1. Press the ON / OFF button. The display shows the remaining power and the activated output ports.
  2. The display shows a percentage charge from 0% to 100% when the Power Box is fully charged.

Recharge the Power Box before first use and after each use.

CHARGING PROCESS
  1. Plug the USB cable to a charger with a USB output
  2. Plug the USB-C end of the cable to the input port of the Power Box start the charge.

Or

  1. Plug car adaptor to the car cigarette lighter socket.
  2. Plug the other end of the adapter to the input port of the Power Box to start the charge

STARTING THE VEHICLE

Emergency start function for gas or diesel vehicles equipped with a 12V battery.

To start a vehicle, please process as follows:

1| BS-BATTERY-PB-02-Power-Box-14| Connect the jumper cable to the Power Box connector .
---|---|---
2| |

  1. Connect the red clamp to the (+) of the battery.
  2. Connect the black clamp to the (-) of the battery.

3| | If the lights «Start» and «Error» flash alternately in green and red, the product is ready.
If only the «Error» light is on, the internal battery of the Power Box is too low. Charge the product.
4| | If the «Start» light becomes green and the «Error» light turns off, everything is ok. Make a start within 30 seconds.
⚠ Do not exceed 3 starts with a time interval of 30s between each.
5| | After starting, disconnect the smart start cable from its connector and remove the 2
clamps from the vehicle’s battery terminals within 30 seconds.
⚠ Leave the vehicle running.
6| BS-BATTERY-PB-02-Power-Box-19| If all 3 starts fail, check the «Error» light.
A red «Error» light on is synonymous with an engine or connection problem.
7| BS-BATTERY-PB-02-Power-Box-20| After the start- up, if the internal battery is less than 80%, recharge the Power Box.
⚠ Wait at least 30 minutes after starting the vehicle to charge the Power Box POWER.

CHARGING MOBILE PHONES

  1. Plug your cable to the Power Box USB port 1 or USB port 2 .
  2. Select the appropriate adaptor for your mobile phone or table and plug it in. The Power Box launches the charge automatically.

BS-BATTERY-PB-02-Power-Box-21

POWER SUPPLY

  1. Connect a 12V power supply cable (not supplied) to the 12V 5A output port .
  2. Link the power supply cable to the power socket of your 12V electrical device.

FLASHLIGHT FUNCTION

Press the ON/OFF button for 3 seconds to turn on the LEDs.
Briefly press the button to switch lighting modes (3 available modes: normal, stroboscope and SOS).

TECHNICAL SPECIFICATIONS

Battery capacity 12000mAh (44.4Wh)
Input 5V/2A
Output
  • USB1: 5V/2A
  • USB2 (Quick Charge): 5V/3A, 9V/2A, 12V/1,5A
  • 15V/5A

Start current| 600A
Peak current| 1200A
Operation temp| -20°C – 60°C
Size| 170x80x38 mm
Weight| 539g

PROTECTIONS
This device is protected against overload, overheating, overintensity, deep discharge, short circuit and polarity reversal.

TROUBLESHOOTING, CAUSES, SOLUTIONS

| TROUBLESHOOTING| CAUSES| SOLUTIONS
---|---|---|---
1| No answer while pressing the ON/ OFF button| The Power Box is discharged.| Charge the product.
2| «Error» light fixed on the smart start cable.| Internal battery voltage < 11.0V.| Charge the product
3| «Error» indicator flashes + discontinuous beeper| Short circuit.| Check that the clamps are properly connected and disconnect/reconnect the smart start cable.
«Error» indicator flashes + continuous sound signal| Reverse polarity.| Check that the clamps are properly connected and disconnect/reconnect the smart start cable.
«Error» indicator flashes + quick beep| Overheating.| Disconnect the clamps from the battery and the Power Box and wait 5 minutes then reconnect.
Fixed «Start» light

+ «Error» light fixed.

| The clamps have been connected to the battery for more than 30 seconds.| Remove the 2 clamps from the vehicle battery terminals to protect the unit.

MAINTENANCE

The warranty covers faulty workmanship for 1 year from the date of purchase (parts and labor).

The warranty does not cover:

  • Transit damage.
  • Normal wear of parts (eg.: cables, clamps, etc..).
  • Damages due to misuse (power supply error, dropping of equipment, disassembling).
  • Environment related failures (pollution, rust, dust).

In case of failure, return the unit to your distributor together with:

  • The proof of purchase (receipt etc …)
  • A description of the fault reported

www.bs-battery.com

SMART BANK BATTERY CHARGER & MAINTAINER WITH RECONDITIONING FUNCTION
For Lead Acid & Lithium

  • Auto detect lead acid or Lithium technology
  • Charges and maintains 3 batteries with different voltage and technologies at once
  • Adaptable charging algorithm for lead acid & Lithium (LiFePO4)
  • Force mode: to activate low voltage “dead” lead acid battery or wake up “dead” LiFePO4 battery
  • Easy to use: connect & forget

6V/12V – 3x 2A

SMART BATTERY CHARGER & MAINTAINER

WITH RECONDITIONNING FUNCTION
For Lead Acid
Battery size: up to 30Ah (60Ah in maintenance)

  • Smart battery charger & maintainer with reconditioning function
  • Multiaxis hook
  • Ideal for charging during winter season
  • Safe: connection spark free. Reverse polarity, short circuit and internal overheat protection
  • Easy to use: connect & forget

12V – 1.5A

SMART BATTERY CHARGER & MAINTAINER
For Lead Acid & Lithium

  • Smart battery charger & maintainer
  • Auto detect Lead Acid or Lithium technology
  • Adaptable charging algorithm for Lead Acid & Lithium (LiFePO4)
  • Safe: connection spark free, reverse polarity, short circuit and internal overheat protection
  • Easy to use: connect & forget
  • 6V & 12V manual switch selection

6V/12V – 1A

Documents / Resources

| BS BATTERY PB-02 Power Box [pdf] Instruction Manual
PB-02, PB-02 Power Box, Power Box
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

BS BATTERY User Manuals

Related Manuals