wiltec 34132 Airbrush Gun Type 132 User Manual
- June 3, 2024
- wiltec
Table of Contents
User’s manual Airbrush Gun Type 132
34132
34132 Airbrush Gun Type 132
Illustration similarities may vary depending on model
** Please read and follow the operating instructions and safety
information prior to initial operation. Technical changes reserved!
Illustrations, functional steps, and technical data may deviate
insignificantly due to continuous further developments.
The information contained in this document may alter at any time without prior
notice. No part of this document may be copied or otherwise duplicated without
prior written consent. All rights reserved. WilTec Wildanger Technik GmbH
cannot be held liable for any possible mistakes in this operating manual, nor
in the diagrams and illustrations shown. Although WilTec Wildanger Technik
GmbH has made every possible effort to ensure that this operating manual is
complete, accurate, and up-to-date, errors cannot be ruled out entirely. If
you have found an error or wish to suggest an improvement, we look forward to
hearing from you.
Send us an e-mail to: service@wiltec.info
or use our contact form: https://www.wiltec.de/contacts/
The most recent version of this manual in several languages can be found in
our online shop:
https://www.wiltec.de/docsearch
Our postal address is:
WilTec Wildanger Technik GmbH Königsbenden 12 52249 Eschweiler Germany
To return your goods for an exchange, repair, or other purposes, please use
the following address. Attention! To allow for a trouble-free complaint or
return, it is important to contact our customer service team before returning
your goods.
Retourenabteilung**
WilTec Wildanger Technik GmbH Königsbenden 28
52249 Eschweiler Germany
E-mail: service@wiltec.info
Tel: +49 2403 555920
Fax: +49 2403 5559215
Introduction
Thank you for choosing to purchase this quality product. To minimize the risk of injury, we ask you to always take some basic safety precautions when using this product. Please read this operating manual carefully and make sure that you understand it. Keep these operating instructions in a safe place.
Safety instructions
- Familiarise yourself with the user’s manual before using the device. Read it thoroughly and follow all safety and other instructions to avoid damage and injuries.
- Only use the device for its specified purpose. Any incorrect use might lead to injuries and/or damages.
- This device is not suitable for persons (including children) with limited physical, sensory, or mental abilities, lack of experience or knowledge unless they have been instructed and are supervised by an experienced person responsible for their safety and familiar with the device.
- Children must not use the device and should be supervised when they are near it to ensure that they do not play with it.
- Under no circumstances should you direct the device toward your body or other persons’ bodies or animals.
- The maximum capacity must never be exceeded.
- Before any use, check all connections and hoses for proper condition.
- Should the device or hose be damaged, the device must not be used. Risk of injuries!
- Only operate the device in well-ventilated areas.
- Wear appropriate protective equipment (safety glasses, protective gloves, respiratory mask) when operating the device.
- Do not use the device near possible sources of ignition (e.g., cigarettes, open flames, etc.). Paints, thinners, and dissolvents being highly flammable, must be handled with the uttermost care. Obey the warnings and safety instructions given by the manufacturer of the paint, thinner, or dissolvent.
- Clean the device after every use.
- Only have the device repaired by a qualified person.
Before using the product
- Make sure to have received all components of the device and all accessory parts and check them for damages immediately after unpacking them.
- To achieve a regular and clean spray pattern, the surfaces to work on must be clean, dry, free from dust, and free from rust.
Use
-
Connect the gun to a compressed-air connection. Make sure that the air pressure suits the material to be worked on.
-
Thin the paint in accordance with the manufacturer’s instructions and fill the paint into the paint cup. Then close the paint cup properly.
-
Take the gun. Make sure that the compressed-air hoses are not kinked or otherwise blocked.
-
By pressing the trigger, the air will begin to flow. Slowly pull the trigger back to achieve atomizing of the paint.
-
The spray pattern depends on the distance between the spray nozzle and surface.
· Slow movements are recommended for small amounts of paint, and fast movements for large amounts of paint.
· Do not spray arc-shaped patterns and do not pause spraying, as otherwise the paint will not be spread regularly.
· To apply fine lines, remove the needle cover and bring the gun close to the surface.
· Make sure that the distance between the gun and the surface stays constant. -
Switch off the compressed-air supply and let the pressure off as soon as you do not use the gun any longer.
-
Empty the paint cup after work. Drain the paint rests into an appropriate container and dispose of it properly.
Cleaning and maintenance
- Empty the paint cup and clean it out with water or dissolvent it.
- Fill water or dissolvent into the pain cup, then keep the needle holder shut by hand and spray. Thus, the air will flow backward into the nozzle, removing all paint rests.
- It is advisable to spray again without keeping the needle holder shut to allow fresh dissolvent to come into the paint conduct; then re-wash the dissolvent by keeping the needle cover shut by hand. Repeat this several times if necessary.
- Clean all components thoroughly to avoid any deposits.
Technical specifications
| Nozzle diameter (㎜) | 0.3 |
|---|---|
| Paint cup capacity (mℓ) | 7 (with lid) |
| Size (㎜) | 230 × 146 × 33 |
| Max. working pressure (㍴) | 3.5 |
| Weight (㎏) | 0.4 |
Main components
| No | Name |
|---|---|
| 1 | Needle cap |
| 2 | Nozzle |
| 3 | Needle |
| 4 | Paint cup |
| 5 | Double action trigger (air and paint) |
| 6 | Pressure lever |
| 7 | Needle locking screw |
| 8 | Valve gasket |
| 9 | Return spring |
| 10 | Air supply |
| 11 | Chuck |
| 12 | Needle return spring |
| 13 | Spring limiter |
Important Note:
Reproduction and any commercial use (of parts) of this operating manual,
requires a written permission of WilTec Wildanger Technik GmbH.
https://www.XPOtool.com
The Tool Experts
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>