SW-MOTECH HTA.07.945.10000 SLC Side Carrier Left Instruction Manual
- June 4, 2024
- SW-MOTECH
Table of Contents
SW-MOTECH HTA.07.945.10000 SLC Side Carrier Left
MOUNTING INSTRUCTIONS
SLC side carrier
Thank you for choosing this premium product from SW-MOTECH. Please visit our webshop for additional information, such as application charts and PDF mounting instructions. Any other documents that may be required (e.g. ABE certifications), are also available for download at our webshop. Installation and/or maintenance of this product require good technical understanding! For your own safety, SW-MOTECH recommends having installation and/or servicing carried out by a specialist workshop! SW-MOTECH assumes no liability for damage caused by improper installation and/or maintenance work! Carefully follow all the directions given in the mounting instructions and pay attention to all relevant information in the vehicle manual during assembly. Nonconformance can lead to vehicle damage or even endanger the driver! These mounting instructions are written based on our current state of knowledge. Legal requirements for accuracy do not exist. This product was developed for vehicles in their factory setting. Compatibility with original accessory parts or other manufacturers” accessory parts is not guaranteed. Furthermore, BEFORE installing this product, make sure that all moving parts (e.g. the chain) are in the original state of maintenance. Installed accessories can change the driving behavior and/or stability of your vehicle.
GENERAL INFORMATION
Observe the country-specific regulations concerning vehicle registration/ operation as well as TUV regulations if applicable. If required, register installed parts in the vehicle documents through an appropriate inspection authority.
-
PREPARATION:
Read the mounting instructions carefully and make sure that all items of the parts list are included. Make sure that your vehicle is parked safely and cannot fall over. Turn off the engine and remove the ignition key. Let the motor/exhaust cool off if necessary. Disconnect the vehicle battery when working on the electrical system. Use appropriate tools. Have another person to help you. -
MOUNTING:
All parts and connections removed from the vehicle must be reinstalled in accordance with the vehicle manufacturer · specifications or replaced by parts delivered by SW-MOTECH. Secure all threads, unless otherwise specified, with a medium-strength liquid thread locker. Torque specifications undefined by SW- MOTE CH must be obtained from the vehicle manufacturer or by a specialist workshop! -
FUNCTION CHECK:
After installation make sure that all parts and connections previously removed are properly replaced. Also make sure that no moving parts are obstructed and no function of the vehicle is hindered in any way. Cables and hoses must not rub and/or be pinched. Before starting to ride, perform a comprehensive check of all functions. After the first 50 km and then at regular intervals, check the tightening torque of all screw connections and the proper fit of the product.
PARTS LIST
Note:
All measurements in millimeters. b The second number indicates the total
quantity of the part in the delivery. c No torque specifications: Use the
torque defined by the vehicle manufacturer! The standard torque in this table
can be used as long as it is within the vehicle manufacturer’s specifications.
MOUNTING
NOTE: The following mounting steps show the mounting of the left side carrier.
-
Mount the right side carrier in the same way.
-
Attach the parts (2) to (5) to the side carrier (1), as shown in the schematic drawing.
ATTENTION: Use liquid thread locker! -
Tighten the screws as specified.
-
-
Remove the original luggage rack from the vehicle.
-
Attach the side carrier (1) to the vehicle, as shown in the drawing.
- ATTENTION: Use liquid thread locker!
- Tighten the screws with the manufacturer’s specified torque.
- When mounting the side carrier with the SW-MOTECH luggage rack, the spacers (10) are not required. Mount instead the marked parts of the luggage rack.
- Attach the side carrier (1) to the vehicle, as shown in the drawing.
- ATTENTION: Use liquid thread locker!
- Once all parts are aligned without excess tension, tighten the screws as specified.
MOUNTING INSTRUCTIONS Legend Gear Side Bag LC1 / LC2
Thank you for choosing this premium product from SW-MOTECH.
Please visit our webshop for additional information, such as application
charts and PDF mounting instructions. Any other documents that may be required
(e.g. ABE certifications), are also available for download at our webshop. »
www.sw-motech.com Carefully follow all the
directions given in the mounting instructions. Also pay attention to all
relevant information in the vehicle manual during assembly. Nonconformance can
lead to vehicle damage or even endanger the driver! Please keep the mounting
instructions as a reference. SW-MOTECH assumes no liability for damages caused
by improper fixation and handling. This product was developed for vehicles in
their original condition. Compatibility with original accessory parts or other
manufacturers’ accessory parts is not guaranteed. Installed accessories can
change the driving behavior and/or stability of your vehicle.
GENERAL INFORMATION
Please observe any country-specific regulations concerning vehicle registration.
- PREPARATION: Read the mounting instructions carefully and make sure that all parts are included. Make sure that your vehicle is parked safely and cannot fall over. Turn off the engine and remove the ignition key. Let the motor/exhaust cool off if necessary. Make sure to use only the appropriate tools. During installation have another person help you.
- FUNCTION CHECK: This is a universal product. For this reason make sure BEFORE the first use, that the product can be fixed properly and used without problems with your vehicle type.
- ATTENTION: All components of the product must not contact any hot or moving parts of the vehicle. All parts should also remain 5 cm away from hot parts of the vehicle and remain clear of the exhaust stream. After mounting, make sure there are no clearance issues while the suspension is both compressed and extended.
- ATTENTION: Before riding and at each stop (every 200 km) check proper fixation of the product!
- After fixation also makes sure that no moving parts are obstructed and the function of the vehicle is not hindered in any way. Lamps as taillight and turn signals must not be limited in their function. Cables and hoses must not rub and/or be pinched. Before starting to ride, perform a comprehensive check of all functions.
LOADING INFORMATION
- ATTENTION: Riding with this product may affect the motorcycles driving and braking performance! Make sure weight is evenly distributed!
- ATTENTION: Depending on the location of fixation, cornering and ground clearance can be reduced by using this product!
- Never store pointy or sharp-edged objects in the product, which could cause injury to persons or damage to the vehicle/product.
- Use a waterproof inner bag/rain cover to protect your luggage from moisture. Additionally protect sensitive luggage (e.g., electronic equipment) from moisture with a plastic bag.
- ATTENTION: Maximum load: 5 kg / 11 lbs! The maximum vehicle load specified by the manufacturer must not be exceeded!
- ATTENTION: Maximum speed with this product, 130 km/h!
PARTS LIST & CARE
CARE
- Clean the product periodically or after each trip, as dust and dirt have a wear effect and permanent stains can be prevented. Clean the product after riding in salty conditions, to avoid damage from salt.
- First, remove dust and encrustations with a soft dry brush. Remove stubborn deposits with a soft cloth and warm soapy water. Do NOT use strong cleaning agents, rough cleaning tools or a high-pressure washer! Then rinse with clear water.
- Before re-use dry the product for at least 24 hours in the air (not in direct sunlight).
- We recommend impregnating the cotton textile surface of the product in regular intervals or after intensive cleaning with a commercial wax impregnation (e.g. from Fjallravenl.
- ATTENTION: Because the textile surface material is a natural fiber, it will experience color changes or fading when exposed to direct sunlight for extended periods of time and by environmental factors (e.g., SMOG, acid rain, etc.)! SW-MOTECH assumes no liability for this!
- ATTENTION: Dirt on the product and vehicle has an abrasive effect and can damage surfaces, such as the paint. Make sure that all areas of the vehicle, which have contact with the product or parts of the product as straps, are protected with an adhesive protection film from scratches and abrasions. SW-MOTECH assumes no liability for paint damage and abrasions.
FIXATION
-
Fasten the Velcro closure of the side bag (1 a/1 b). Revert the reinforced opening of the side bag (1 a/1 bl twice completely.
-
Fix the shown loops with the side-mounted hook buckles.
-
Tighten the straps of the hook buckle. Secure the opening of the side bag (1 a/1 b) with the shown strap.
-
Place the three openings of the quick release fastening system onto the locating bolts of the mounted SLC side carrier.
-
Press the side bag (1 a/1 bl slightly downward, until it properly rests on SLC side carrier.
ATTENTION: Make sure that all three locating bolts engage at the same time!
Pay attention to the clearly audible snap sound of the locking mechanism!
-
To release the side bag (1 a/1 bl simply press the shown slider of the locking mechanism downward.
Fixation and vehicle are examples.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>