Lightstar LMSA-500 AIRLITE Series Bi-Color LED Balloon 500w User Manual

June 4, 2024
Lightstar

Lightstar logo AIRLITE Series
User Manual
Version: 23. Dezember 2021, 11:37 AM 

Lightstar LMSA-500 AIRLITE Series Bi-Color LED Balloon
500w

Product Overview

Lightstar LED Airlite is a Bi-Color LED Balloon light. It features:

  • high efficiency
  • low power consumption
  • low operating temperature
  • Color temperatures from 2800 – 6500K
  • DMX and Wireless DMX Product Features
  • 360° light illumination
  • self-inflatable system – replenishes air automatically
  • high quality bi-color light, CRI = 95
  • brightness adjustable from 0 – 100%
  • color temperature adjustable between 2800K and 6500K
  • luminous flux output stays relatively stable when the temperature is adjusted
  • supports DMX512 protocol
  • LCD software control is easy to operate
  • adjustable frequency from 1Hz to 50Hz
  • no UV output
  • lamp and power supply are easy to maintain

Technical Information

SKU: Description:
Power: Material:
Cooling:
Color Temperature:
Dimming:
CRI:
TLCI:
AC Input (indirect):
Control:
Frequency:
IP Class:
Diameter (inflated):
Dimensions:
Weight:| LMSA-2000
Bi-Color LED Spotlight
1000W
different materials
Active Cooling
2800-6500K
0-100%
95

96
100-240V AC
DMX In- & Output (5-Pin XLR socket)
1-50Hz
IP20
1800mm
300 x 1500mm
8‘000g
---|---

Operational Instructions

Connect the power supply to the input socket of the lamp head. The fan will inflate at 100% speed automatically. After 10 seconds, the light brightness will turn on 10%. 1 minute later, the light brightness becomes 100%. 2 minutes later, the light is fully inflated and it enters the fan mode to sustain the air level. The fan turns to 20% speed to sustain air level and reduce operating noise.
Enter fan mode from the menu, or click button E to enter the silent fan mode.
This will reduce noise a lot – due to the reduced fan speed of 15%. The fan control function is not available under fan mode. If you need more inflation, turn off the silence mode.
Once the lamp is restarted, it will power on. According to the above-mentioned procedure, it will inflate at full speed for 2 minutes. To prevent overload of air, you can click button E to stop the inflation.
The home screen shows the brightness value which can be adjusted by turning the adjustment knob on the right side of the display. Select button A to adjust color temperature. Select button A or M to switch back to the home screen.

Lightstar LMSA-500 AIRLITE Series Bi-Color LED Balloon 500w -
fig1Lightstar LMSA-500 AIRLITE Series Bi-Color LED Balloon
500w - fig3

On the light mode screen, select the corresponding adjustment parameters by selecting operating buttons, and then adjust the parameter data by adjusting the knob. The same procedure goes through the menu, as well as in the FAN mode.

DMX Control

There are two kinds of DMX signal control: Wireless DMX and DMX. By default, DMX is selected. There are 5-Pin XLR In- & Outputs on the console for DMX via cable. For wireless DMX, there is an antenna mounted on the side of the ballast.
DMX512 Data Pinout is as followed:

Pin 1 Data Link Common GND
Pin 2 Signal GND
Pin 3 Signal +
Pin 4 is not used
Pin 5 is not used

On the menu screen, select DMX to adjust DMX settings. By turning the adjustment knob, you can select the start address from 1 – 512.

Further adjustments are made as mentioned before.

Wireless DMX Control

Click the push button to show current ID settings. Click the push button to increase the number.

  • Red
  • green
  • Yellow
  • Blue
  •  Purple
  • Bluish Green
  •  White

Working Status:

LED is always on no DMX or no signal
Red LED flashing sending
Green LED flashing receiving

RF frequency features 126 bands, which are selected automatically to avoid interference.

Communication

  1. Power on the transmitter and receiver
  2. Press the key, and set the same ID for transmitter and receiver. If there is more than one group of wireless LANs, make sure the ID of each network is different.
  3. After the sender receives DMX data, the sender will select a non-interfering frequency band. The receiver will change communication bands until the same ID data is found (green LED flashes). If DMX data communication has been established, LED will blink faster.

Notice and Maintenance

  1. LED‘s operating temperature range must be guaranteed between – 20°C to +40°C. Overheating or undercooling can both reduce the fixture’s life span.
  2. The product must be placed on a solid, flat, and dry surface. The surface temperature should be less than 50°C. Avoid exposure to direct sunlight and operation in an environment with high humidity or explosive gas.
  3. Do not beat, knock or shake the light violently or it may influence the normal use of the light.
  4. Do not cover lamps with paper, cloth, or similar materials that could ignite due to high temperatures.
  5. Put the lamp in a cool and dry place when you do not use it for a long time.
  6. Avoid any flammable liquid, water, or metal material entering the machi- ne. Cut off the power supply as soon as this happens.
  7. Do not use machines in dirty and dusty environments and clean them regularly.
  8. The technicians must get professional training to install, operate or repair leds.
  9. If any equipment from Lightstar doesn‘t work properly, please get in contact with a Lightstar special repair department or a professional technician. Do not disassemble or reassemble the parts by yourself.

Service Warranty Ordinance

Customers enjoy a one-year free warranty service as of the date of purchasing our product.

  1. If the expiry date of the warranty is reached, our product can still be repaired according to price.

  2. In any of the following circumstances, the product is not repaired free of charge, whether the warranty period expires or not.
    – Damage caused by misuse or abuse, disassembly, and non-original parts replacement.
    – Damage caused by natural disasters, unconventional voltage, and environmental factors

  3. Lightstar will remain in the power of interpretation.

  4. Software version modification without further notice.

Lightstar LMSA-500 AIRLITE Series Bi-Color LED Balloon 500w
-Lightstar logo

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals