SW-MOTECH STP.06.590.11300/B Frame Protection Pads for Yamaha Motorcycles Instruction Manual

ANBAUANLEITUNG
mounting instructions
STP.06.590.11300/B Frame Protection Pads for Yamaha Motorcycles
Instruction Manual

STP.06.590.81300/B
STP.00.590.10001/B

MOUNTING INSTRUCTIONS

Revision: 00 – Datum / Date: 06 – 2021
Mounting kit for frame slider
Thank you for choosing this premium product from SW-MOTECH. Please visit our webshop for additional information, such as application charts and PDF mounting instructions. Any other documents that may be required (e.g. ABE certifications), are also available for download at our webshop.
Installation and/or maintenance of this product require good technical understanding! For your own safety, SW-MOTECH recommends having installation and/or servicing carried out by a specialist workshop! SW-MOTECH assumes no liability for damage caused by improper installation and/or maintenance work!
Carefully follow all the directions given in the mounting instructions and pay attention to all relevant information in the vehicle manual during assembly. Nonconformance can lead to vehicle damage or even endanger the driver! These mounting instructions are written based on our current state of knowledge. Legal requirements for accuracy do not exist.
This product was developed for vehicles in their factory setting. Compatibility with original accessory parts or other manufacturers’ accessory parts is not guaranteed. Furthermore, BEFORE installing this product, make sure that all moving parts (e.g. the chain) are in the original state of maintenance. Installed accessories can change the driving behavior and/or stability of your vehicle.

GENERAL INFORMATION
Observe the country: specific regulations concerning vehicle registration/ operation as well as TUV regulations if applicable. If required, register installed parts in the vehicle documents through an appropriate inspection authority.
PREPARATION: Read the mounting instructions carefully and make sure that all items on the parts list are included. Make sure that your vehicle is parked safely and cannot fall over. Turn off the engine and remove the ignition key. Let the motor/exhaust cool off if necessary. Disconnect the vehicle battery when working on the electrical system. Use appropriate tools. Have another person to help you.
MOUNTING: All parts and connections removed from the vehicle must be reinstalled in accordance with the vehicle manufacturer’s specifications or replaced by parts delivered by SW-MOTECH. Secure all threads, unless otherwise specified. with a medium-strength liquid thread locker.
Torque specifications undefined by SW-MOTECH must be obtained from the vehicle manufacturer or by a specialist workshop!
FUNCTION CHECK: After installation makes sure that all parts and connections previously removed are properly replaced. Also, make sure that no moving parts are obstructed and no function of the vehicle is hindered in any way. Cables and hoses must not rub and/or be pinched. Before starting to ride, perform a comprehensive check of all functions. After the first 50 km and then at regular intervals, check the tightening torque of all screw connections and the proper fit of the product.

SW-MOTECH GmbH & Co. KG
Renewed 7-10
35282 Rauschenberg
Germany| Tel. /phone + 49 (0)6425 / 8168 – 050
Fax / fax + 49 (0)6425 / 8168 – 10
www.sw-motech.com
---|---

  PART LIST

step| No| Item No./Description| Part| Quantity| N’m
---|---|---|---|---|---
1| 1| STP.00.590.003| Mounting Plate| 2 /2|
| 2| M12 x 120; DIN 912| Hexagon Socket Screw; fine thread| 2 /2| OEM
| 3| STP.01.590.003| Stepped Spacer; black| 2 /2|
| 4| 25/0 12,5 /h20| Spacer| 2 /2|
2| 5| STP.00.590.002| Adapter Plate| 2 /2|
| 6| M6 x 40; DIN 912| Hexagon Socket Screw| 2/4| 6

8.8

10.9

Note:. All measurements in millimeters. a The second number indicates the total quantity of the part in the delivery.
c No torque specifications: Use the torque defined by vehicle manufacturer! The standard torque in this table can be used as long as it is within the vehicle manufacturer’s specifications.

MOUNTING

ATTENTION: Do not start mounting the right frame slider until you have completed the installation of the left frame slider!
Remove the original engine bolt from the left mounting point. Attach the mounting plate (1) to the vehicle, as shown in the drawing.
ATTENTION: Use a liquid thread locker!
Before tightening the screw (2), adjust the mounting plate (1) according to the alignment of the vehicle. Tighten the screw (2) with the manufacturer’s specified torque. Repeat the installation on the right side of the vehicle.

Attach the shown parts to the mounting plates 111 on both sides.
NOTE: Also refer to the mounting instructions of the frame slider set
ATTENTION: Use a liquid thread locker! Tighten the screws (6) as specified.

MOUNTING INSTRUCTIONS

Revision: 00 – Datum / Date: 10 – 2019
Crash Pad Set

Thank you for choosing this premium product from SW-MOTECH. Please visit our webshop for additional information, such as application charts and PDF mounting instructions. Any other documents that may be required (e.g. ABE certifications), are also available for download at our webshop.

Installation and/or maintenance of this product require good technical understanding! For your own safety SW-MOTECH recommends having installation and/or servicing carried out by a specialist workshop! SW-MOTECH assumes no liability for damage caused by improper installation and/or maintenance work!

Carefully follow all the directions given in the mounting instructions and pay attention to all relevant information in the vehicle manual during assembly. Nonconformance can lead to vehicle damage or even endanger the driver! These mounting instructions are written based on our current state of knowledge. Legal requirements for accuracy do not exist.

This product was developed for vehicles in their factory setting. Compatibility with original accessory parts or other manufacturers’ accessory parts is not guaranteed. Furthermore, BEFORE installing this product, make sure that all moving parts (e.g. the chain) are in the original state of maintenance. Installed accessories can change the driving behaviour and/or stability of your vehicle.

GENERAL INFORMATION

Observe the country-specific regulations concerning vehicle registration/ operation as well as TUV regulations if applicable. If required, register installed parts in the vehicle documents through an appropriate inspection authority.

PREPARATION: Read the mounting instructions carefully and make sure that all items of the parts list are included. Make sure that your vehicle is parked safely and cannot fall over. Turn off the engine and remove the ignition key. Let the motor/exhaust cool off if necessary. Disconnect the vehicle battery when working on the electrical system. Use appropriate tools. Have another person to help you.

MOUNTING: All parts and connections removed from the vehicle must be reinstalled in accordance with the vehicle manufacturer’s specifications or replaced by parts delivered by SW-MOTECH. Secure all threads, unless otherwise specified, with a medium-strength liquid thread locker. Torque specifications undefined by SW-MOTECH must be obtained from the vehicle manufacturer or by a specialist workshop!

FUNCTION CHECK: After installation make sure that all parts and connections previously removed are properly replaced. Also make sure that no moving parts are obstructed and no function of the vehicle is hindered in any way. Cables and hoses must not rub and/or be pinched. Before starting to ride, perform a comprehensive check of all functions. After the first 50 km and then at regular intervals, check the tightening torque of all screw connections and the proper fit of the product.

SW-MOTECH GmbH & Co. KG
Renewed 8-10
35282 Rauschenberg
Germany| Tel. /phone + 49 (0)6425 / 8168 – 050
Fax / fax + 49 (0)6425 / 8168 – 10
www.sw-moParttech.com
---|---

PART LIST

8.8

10.9

Note: All measurements in millimeters. The second number indicates the total quantity of the part in the delivery.
c No torque specifications: Use the torque defined by the vehicle manufacturer! The standard torque in this table can be used as long as it is within the vehicle manufacturer’s specifications.

Step [1]: Attach the crash pads (1) on both sides to the adapter plates of your SW-MOTECH slider set for a frame, as described in the mounting instructions of the slider set for the frame.
Step [2]: Place the logo inserts (2) on both sides into the crash pads
Step [3]: attach them with the screws (3).
Tighten the screws (31 CAREFULLY by hand (max. 1,2 N’m1!

SW-MOTECH GmbH & Co. KG
Renewed 7-10
35282 Rauschenberg
Germany| Tel. /phone + 49 (0)6425 / 8168 – 050
Fax / fax + 49 (0)6425 / 8168 – 10
www.sw-motech.com
---|---

Copyright by SW-MOTECH GmbH & Co. KG
Errors and omissions excepted. Technical and design modifications are subject to change.

Documents / Resources

| SW- MOTECH STP.06.590.11300/B Frame Protection Pads for Yamaha Motorcycles [pdf] Instruction Manual
STP.06.590.81300 B, STP.00.590.10001 B, STP.06.590.11300 B, Frame Protection Pads for Yamaha Motorcycles, STP.06.590.11300 B Frame Protection Pads for Yamaha Motorcycles
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>