SW-MOTECH FRS.11.112.10103 EVO Footrest Kit Instruction Manual
- June 4, 2024
- SW-MOTECH
Table of Contents
11.112.10103 EVO Footrest Kit
Instruction Manual
FRS. 11.112.80103/S
FRS.00.112.10000
EVO footrest kit
Thank you for choosing this premium product from SW-MOTECH. Please visit our webshop for additional information, such as application charts and PDF mounting instructions. Any other documents that may be required (e.g. ABE certifications), are also available for download at our webshop. Installation and/or maintenance of this product require good technical understanding! For your own safety SW-MOTECH recommends having installation and/or servicing carried out by a specialist workshop! SW-MOTECH assumes no liability for damage caused by improper installation and/or maintenance work! Carefully follow all the directions given in the mounting instructions and pay attention to all relevant information in the vehicle manual during assembly. Nonconformance can lead to vehicle damage or even endanger the driver! These mounting instructions are written based on our current state of knowledge. Legal requirements for accuracy do not exist. This product was developed for vehicles in their factory setting. Compatibility with original accessory parts or other manufacturers’ accessory parts is not guaranteed. Furthermore, BEFORE installing this product, make sure that all moving parts (e.g. the chain) are in the original state of maintenance. Installed accessories can change the driving behavior and/or stability of your vehicle.
GENERAL INFORMATION
Observe the country: specific regulations concerning vehicle registration/
operation as well as TUV regulations if applicable. If required, register
installed parts in the vehicle documents through an appropriate inspection
authority. PREPARATION: Read the mounting instructions carefully and make sure
that all items of the parts list are included. Make sure that your vehicle is
parked safely and cannot fall over. Turn off the engine and remove the
ignition key. Let the motor/exhaust cool off if necessary. Disconnect the
vehicle battery when working on the electrical system. Use appropriate tools.
Have another person to help you. MOUNTING: All parts and connections removed
from the vehicle must be reinstalled in accordance with the vehicle
manufacturer’s specifications or replaced by parts delivered by SW-MOTECH.
Secure all threads, unless otherwise specified, with a medium-strength liquid
thread locker. Torque specifications undefined by SW-MOTECH must be obtained
from the vehicle manufacturer or by a specialist workshop!
FUNCTION CHECK: After installation makes sure that all parts and
connections previously removed are properly replaced. Also, make sure that no
moving parts are obstructed and no function of the vehicle is hindered in any
way. Cables and hoses must not rub and/or be pinched. Before starting to ride,
perform a comprehensive check of all functions. After the first 50 km and then
at regular intervals, check the tightening torque of all screw connections and
the proper fit of the product.
PRODUCT-SPECIFIC INFORMATION ATTENTION:
The ground clearance can be reduced by this product! Special care should be
taken when cornering at extreme lean angles!
PARTS LISTS
Schritt
Step| Nr. No.| Art.-Nr./Bezeichnung
Item No./Description| Part| Anzaht Quantity| Nm
---|---|---|---|---|---
2| (1)| FRS.11.112.Y04L / R| Hinge Adapter; left / right| 2 /2|
| (2)| FRS.00.011.004| Hinge Spring| 2 /2|
(3)| 0 14/0 8,2 / h 6| Spacer| 2 /2|
3| (4)| FRS.00.112.002| Positioning Cone| 2 /2|
| | | | |
4| (5)| FRS.00.112.001| EVO Footrest| 2 /2|
| | | |
5| (6)| FRS.00.112.005| Mounting Plate| 2 /2|
| (7)| M8 x 35; DIN 912; 10.9| Hexagon Socket Screw| 2 /2| 30
(8)| KEK.00.M6.ISK| Plastic Cap| 2 /2|
| | | |
11| (9)| FRS.00.112.900.01| Rubber Pad| 2 /2|
| (10)| M5 x 12; DIN 933| Hexagon Screw; stainless steel| 2 /2| 3,5
(11)| d 5,3; DIN 9021| Washer; stainless steel| 2 /2|
- All measurements in millimeters.
** The second number indicates the total quantity of the part in the delivery.
*** No torque specifications: Use the torque defined by the vehicle manufacturer! The standard torque in this table can be used as long as it is within the vehicle manufacturer’s
specifications
Artiket FRS.11.112.10103 beinhaltet:
FRS.00.112.10000: (4), (5), (6), (9), (10), (11)
FRS.11.112.80103/S: (1), (2), (3), (7), (8)
Item FRS.11.112.10103
contains: FRS.00.112.10000: (4), (5), (6), (9), (10), (11)
FRS.11.112.80103/S: (1), (2), (3), (7), (8)
MOUNTING
NOTE: Schematic illustration; Appearance may vary.
NOTE: The installation is shown on the left side of the vehicle only.
Repeat the same procedure on the right side of the vehicle.
NOTE: Before removing the original footrest, make sure to note the order
and direction of the original fixing parts. Remove the original footrest.
Clean the footrest holder thoroughly. Apply some grease to the inside of the
footrest holder and the original pin (Orig.). Attach the hinge adapter (1)
with the shown original parts (Orig.) to the footrest mount.
ATTENTION: The beveled surface of the hinged adapter (1) must be faced
upwards!
Insert the positioning cone (4) onto the star-shaped cone of the hinged
adapter (1). The height of the EVO footrest (5) can be adjusted individually
by the various mounting positions (see right detail drawing).
ATTENTION: Make sure to align the positioning cones (4) synchronously on
each side! For orientation use the markings on the hinged adapter (1) and the
positioning cone (4) (see left detail drawing).
Insert the EVO footrest (5) onto the positioning cone (4). The inclination
angle of the EVO footrest 151 can be adjusted individually by the toothing of
the positioning cone 141 (not more than 18°; see right detail drawing).
ATTENTION: Make sure to align the EVO footrests (5) synchronously on each
side! For orientation use the markings on the positioning cone 14) (see left
detail drawing).
Attach the EVO footrest (5) LOOSELY to the hinged adapter (1), as
shown in the drawing. Check the synchronous alignment once again and the
ergonomics. Then attach the EVO footrest 15) to the hinged adapter 111.
ATTENTION: Use a medium-strength liquid thread locker! Tighten the screw
as specified in the parts list.
NOTE: This step is optional. Attach the rubber pad (9) to the EVO
footrest (5), as shown in the drawing.
ATTENTION: Use a medium-strength liquid thread locker! Tighten the screw
as specified in the parts list.
Schritt Nr. Art.-Nr. / Bezeichnung
Step No. Item No. / Description| Part| Anzaht ”
Quantity “| Nm’
---|---|---|---
1 (1) FRS.00.112.001| EVO Footrest| 2 /2|
(2)FRS.00.112.002| Positioning Cone| 2 /2|
(3)FRS.00.112.005| Mounting Plate| 2 /2|
| | |
(4)FRS.00.112.900.01| Rubber Pad| 2 /2|
(5)M5 x 12; DIN 933| Hexagon Screw; stainless steel| 2 /2| 3,5
(6)d 5,3; DIN 9021| Washer; stainless steel| 2 /2|
| 
---|---
ATTENTION: Pay attention to the mounting instructions included with the
EVO footrest kit!
Copyright by SW-MOTECH GmbH & Co. KG Errors and omissions excepted. Technical
and design modifications are subject to change.
SW-MOTECH GmbH & Co. KG
Ernteweg 8/10
35282 Rauschenberg
Germany
Tel / phone + 49 (0)6425 / 8168 – 050
Fax / fax + 49 (0)6425 / 8168 – 10
infofasw-motech.com
www.sw-motech.com
Documents / Resources
| SW-
MOTECH FRS.11.112.10103 EVO Footrest
Kit
[pdf] Instruction Manual
FRS.11.112.80103 S, FRS.00.112.10000, FRS.11.112.10103, EVO Footrest Kit,
FRS.11.112.10103 EVO Footrest Kit
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>