SW-MOTECH BC.HTA.01.914.30000/B URBAN ABS Side Case System for Honda CBR650R Instruction Manual
- June 4, 2024
- SW-MOTECH
Table of Contents
SW-MOTECH BC.HTA.01.914.30000/B URBAN ABS Side Case System for Honda
CBR650R
MOUNTING INSTRUCTIONS
GENERAL INFORMATION
Observe the country-specific regulations concerning vehicle registration/ operation as well as TUV regulations if applicable. If required, register installed parts in the vehicle documents through an appropriate inspection authority.
PREPARATION: Read the mounting instructions carefully and make sure that all items of the parts list are included. Make sure that your vehicle is parked safely and cannot fall over. Turn off the engine and remove the ignition key. Let the motor/exhaust cool off if necessary. Disconnect the vehicle battery when working on the electrical system. Use appropriate tools. Have another person to help you.
MOUNTING: All parts and connections removed from the vehicle must be
reinstalled in accordance with the vehicle manufacturers· specifications or
replaced by parts delivered by SW-MOTECH. Secure all threads, unless otherwise
specified, with medium-strength liquid thread locker.
Torque specifications undefined by SW-MOTE CH must be obtained from the
vehicle manufacturer or by a specialist workshop!
FUNCTION CHECK: After installation make sure that all parts and connections previously removed are properly replaced. Also make sure that no moving parts are obstructed and no function of the vehicle is hindered in any way. Cables and hoses must not rub and/or be pinched. Before starting to ride, perform a comprehensive check of all functions. After the first 50 km and then at regular intervals, check the tightening torque of all screw connections and the proper fit of the product.
PARTS LIST
All measurements in millimeters. • ** The second number indicates the total
quantity of the part in the delivery. *** No torque specifications: Use the
torque defined by vehicle manufacturel’! The standard torque in this table can
be used as long as it is within the vehicle manufacturer’s specifications
.
MOUNTING
NOTE: The mounting steps [1] to [3] show the mounting of the left side
carrier.
Mount the right side carrier in the same way as on the left side of the
vehicle.
Attach the parts [2) to [5) to the side carrier [1). as shown in the drawing.
ATTENTION: Use liquid thread locker!
Tighten the screws as specified.
Remove the shown original screws from the vehicle.
Attach the side carrier [1) to the vehicle, as shown in the drawing.
ATTENTION: Use liquid thread locker!
Tighten the screws with the manufacturer’s specified torque.
MOUNTING INSTRUCTIONS
GENERAL INFORMATION
Observe the country-specific regulations concerning vehicle registration/operation as well as TUY regulations if applicable. If required, register installed parts in the vehicle documents through an appropriate inspection authority.
PREPARATION: Read the mounting instructions carefully and make sure that all items of the parts list are included. Make sure that your vehicle is parked safely and cannot fall over. Turn off the engine and remove the ignition key. Let the motor/exhaust cool off if necessary. Disconnect the vehicle battery when working on the electrical system. Use appropriate tools. Have another person to help you.
FUNCTION CHECK: This is a universal product. For this reason make sure BEFORE the first use, that the product can be fixed properly and used without problems with your vehicle type. After fixation also make sure that no moving parts are obstructed and the function of the vehicle is not hindered in any way. Lamps as taillight and turn signals must not be limited in their function. Cables and hoses must not rub and/or be pinched. Before starting to ride, perform a comprehensive check of all functions.
PRODUCT SPECIFIC INFORMATION
ATTENTION: Riding with this product may affect the motorcycles driving
and braking performance!
ATTENTION: Depending on the location of fixation, cornering and ground
clearance can be reduced by using this product!
ATTENTION: Before riding and at each stop (every 200 km) check proper
fixation of the product!
ATTENTION: The maximum vehicle load specified by the manufacturer must not be exceeded!
PARTS LIST
All measurements in millimeters. • ** The second number indicates the total quantity of the part in the delivery. *** No torque specifications: Use the torque defined by vehicle manufacturel’! The standard torque in this table can be used as long as it is within the vehicle manufacturer’s specifications.
Care
To clean the side case, use warm, soapy water and a soft, clean cloth. Rinse
with clean water. Do NOT use strong cleaning agents, rough cleaning tools or
high pressure washer!
Clean the side case after riding in salty conditions, to avoid damage from
salt.
Hard-to-open zippers can be loosened with a small amount of talcum powder.
ATTENTION: Surface materials can experience color changes or fading when exposed to direct sunlight for extended periods of time and by environmental factors (e.g., SMOG, acid rain, etc.)! SW-MOTECH assumes no liability for this.
MOUNTING
Place the three locking openings of the side case onto the guide bolts of the mounted SLC side carrier. Then press the side case slightly downward, until it properly rests on the SLC side carrier.
ATTENTION: Make sure that all three guide bolts engage at the same time!
Pay attention to the clearly audible snap sound of the locking mechanism and
that the red marking under the slider is not visible!
To release press the slider downward.
ATTENTION: All components of the side case must not contact any hot or
moving parts of the vehicle! All parts should also remain 5 cm away from hot
parts of the vehicle and remain clear of the exhaust stream! After mounting,
make sure there are no clearance issues while the suspension is both
compressed and extended. 
Open the mounted side case (1) to protect it against theft.
Now press the locking button and turn it according to the arrow mark until the
locking button engages.
Then lock the closed zipper with the included lock (2)
We recommend leaving the locking button in the closed position during the
ride. 
Use the included waterproof innerbag (3) to protect your luggage
from moisture. 
For an easier loading of the side case (11. open the buckles and
hook and loop fasteners of the opening reductions, as shown in the drawing.
ATTENTION: Make sure weight is evenly distributed between the
left and right side if you want to use both side cases! Make sure that the
loanding is secured against shifting during the ride!
ATTENTION: Never store pointy or sharp-edged objects, which could cause
injury to persons or damage to the vehicle/side case!
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>