SAMSUNG RB3000J Freezer User Manual
- June 8, 2024
- Samsung
Table of Contents
SAMSUNG RB3000J Freezer User Manual
-
You can check where to buy replacement parts at http://samsung.com/support
-
Visit the part purchase site and enter the model code of your product to check the parts available for purchase. The model code is labelled on the outer side of your product.
– You can check the model code and version on the barcode label at the bottom left of the product. -
For replacement parts, make sure the part name matches that of the illustration in this manual.
– User-serviceable parts are limited to handles (some models only), gaskets, drawers, and hinges.
NOTE
Following the repair by a non-authorised service provider, self-repair or non-
professional repair of the product, Samsung is not liable for any damage to
the product, any injury or any other product safety issue caused by any
attempt to repair the product which does not carefully follow these repair and
maintenance instructions. Any damage to the product caused by an attempt to
repair the product by any person other than a Samsung certified service
provider will not be covered by the warranty.
CAUTION
- The part name listed on the site may differ from that in this manual. Please make sure you choose the right part name.
- Replacing hinges requires extreme caution because it involves detaching the door.
- Be sure to wear safety gloves while making repairs.
The actual image and provided parts of the refrigerator may differ, depending on the model and the country.
- Cover hinge
- Drawer
- Middle hinge
- Barcode label
- Hinge low
- Handles (Applicable models only)
Handle replacement
CAUTION
- When replacing the door handle, take care not to scratch the front of the door.
- Firmly press the handles at the supports. Make sure there is no gap between the supports and the door.
- Tightly fasten the screws when attaching the handle.
- Check that the handle is firmly attached before using the product.
Tools required (not provided)
To detach the handles
Remove the Cap Handle and the Screws by Flat-Head (-) screwdriver.
NOTE
Remove the Cap by Flat-Head (-) screwdriver and assemble the Handle and Cap-
Handle.
Gasket replacement
CAUTION
Make sure you firmly attach the gasket. Otherwise, cold air from the
refrigerator may leak.
To remove the gasket
Open the door and remove the gasket from the door.
To replace the gasket
Attach a new gasket to the refrigerator door.
Make sure there is no gap between the newgasket and the door.
Drawer replacement
CAUTION
Check that the drawer is inserted properly into the rail during assembly.
To remove the drawer
- Pull out the drawer as far as it goes.
- Tilt the drawer up and pull it out until it is removed.
To reattach the drawers
Reattaching the drawers follows the reverse order of their respective removal
steps.
Hinge replacement
To replace the hinges, you must remove the doors first.
CAUTION
- When removing the doors, take extreme caution because the doors are heavy.
- Before replacing the hinges, put a soft pad such as cardboard on the floor to prevent scratches on the door when you place the doors down.
- As the hinges must be handled carefully and replaced by two or more persons, we recommend you to call for professional technical service.
- If you remove the hinge without holding the door, the door may fall and cause injury.
- Ensure that the shaft is firmly tightened on the hinge.
- Check that the hinge is firmly attached to the cabinet.
- Make sure the wire connectors are connected properly.
- Be careful not to damage the wires when fastening the top cover.
WARNING
- Tilting/laying the refrigerator requires a minimum of 2 people.
- Disconnect the power cord before reversing the doors.
Tools required (not provided)
Reversing the door
1. Remove the Cover Wire Door.
2. Disassemble the Cap space Door.
3. Remove the Cover Hinge to push a hook like below Pictures.
- Insert a flat-head screwdriver and put it back as shown in Figure #1.
- As shown in Figure #2, Lever up the cover and push a hook as shown in Figure #3. (Take care not to damage the Cover Hinge Wire by pushing it too hard)
- Disassemble it by pushing the A in Figure #4 by hand as Figure #5.
4. Disconnect the wiring connector for the fridge door. (Only on models with external display).
5. Remove the screws. (Be careful not to drop the door when you disassemble it.)
Read More About This Manual & Download PDF:
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>