SW-MOTECH BC.HTA.07.740.30700 Blaze H Panniers Saddlebag Set Instruction Manual
- June 4, 2024
- SW-MOTECH
Table of Contents
SW-MOTECH BC.HTA.07.740.30700 Blaze H Panniers Saddlebag Set
INTRODUCTION
Thank you for choosing this quality product from SW-MOTECH and BAGS- CONNECTION. The installation and/or maintenance of this product requires a good technical understanding. For your own safety SW-MOTECH and BAGS- CONNECTION recommend having installation and/or service carried out by a specialist workshop. SW-MOTECH and BAGS-CONNECTION assume no liability for damages caused by improper installation and/or service. Carefully follow all the directions given in the mounting instructions. Also, pay attention to all relevant information in the vehicle manual during assembly. Nonconformance can lead to damage to the vehicle or risk to the rider! Please keep the mounting instructions as a reference. This product was developed for vehicles in their original condition. Compatibility with original accessory parts or accessory parts of other manufacturers is not guaranteed. Installed accessories can change the driving behavior and/or stability of your vehicle. Please visit our webshop for additional information, such as application charts and PDF mounting instructions. Any other documents that may be required such as ABE]. are also available for download on our webshop.
GENERAL INFORMATION
Observe any country-specific regulations by law or TOV regulations. If required, enter the installed parts into the vehicle documents with the appropriate inspection authority.
- PREPARATION: Read the mounting instructions carefully and make sure that all parts are included. Make sure that your vehicle is parked safely and cannot fall over. Turn off the engine and remove the ignition key. Let the motor/exhaust cool off if necessary. Disconnect the vehicle battery when working on the electrical system. Make sure to use only the appropriate tools. During installation have another person to help you.
- MOUNTING: All parts and connections removed from the vehicle must be reinstalled in accordance with the vehicle manufacturer’s specifications or replaced by the SW-MOTECH and BAGS-CONNECTION delivered parts and hardware. Secure all threads, unless otherwise specified, with a medium-strong strength liquid thread locker. If not otherwise defined by the vehicle manufacturer or SW-MOTECH and BAGS-CONNECTION, bolts and nuts must be tightened according to DIN/ISO specifications. After installation is complete, be sure that all parts and hardware previously removed are properly replaced.
- FUNCTION CHECK: After installation makes sure all moving parts are unobstructed and the normal function of the vehicle is not hindered in any way. Cables and hoses may not rub and/or be pinched. Before starting to ride, perform a comprehensive check of all functions. Regularly check I every 1 DO km] for the proper seating of all parts and connections removed during installation.
PRODUCT SPECIFIC INFORMATION
ATTENTION: Please pay attention to the information sheet included! in the panniers.SW-MOTECH GmbH & Co. KG & BAGS-CONNECTION GmbH & Co. KG
- Renewed 8/ 10
- 35282 Rauschenberg
- Germany
- Tel. +49(0]6425/8168- 00 · Fax+49(0]6425/8168- 10
- info@sw-bc.com
- www.sw-bc.com
Parts List
Mounting
Attach the shown parts on the mounting brackets (1) (left side mounting bracket shown.
- ATTENTION: Tighten the screws as specified in the parts list! Over-tightening the screws will damage the plastic parts! The shown buckles will come with your panniers. Attach them as shown in the detailed drawing.
- NOTE: Please pay attention to the information sheet included in the panniers.
Mount the parts as shown
- ATTENTION: Make sure the engraving of the panniers frames (9) is located on the side of the clips as shown in the detailed drawing)!
- ATTENTION: Tighten the screws as specified in the parts list! Over-tightening the screws will damage the plastic parts!
- ATTENTION: Make sure the panniers frames (9) fit properly after tightening the screws (11]!
Remove the shown screws on both sides of the vehicle and attach the mounting
brackets (1) and (5) to the vehicle, as shown in the drawing.
ATTENTION: Use a liquid thread locker
ATTENTION: Pay attention to the audible clicking sound! Before riding check the proper fit of the panniers frames.
MOUNTING INSTRUCTIONS
Thank you for choosing this premium product from SW-MOTECH. Please visit our webshop for additional information, such as application charts and PDF mounting instructions. Any other documents that may be required (e.g. ABE certifications) are also available for download at our webshop. Installation and/or maintenance of this product require good technical understanding! For your own safety, SW-MOTECH recommends having installation and/or servicing carried out by a specialist workshop! SW-MOTECH assumes no liability for damage caused by improper installation and/or maintenance work! Carefully follow all the directions given in the mounting instructions and pay attention to all relevant information in the vehicle manual during assembly. Nonconformance can lead to vehicle damage or even endanger the driver! These mounting instructions are written based on our current state of knowledge. Legal requirements for accuracy do not exist. This product was developed for vehicles in their factory setting. Compatibility with original accessory parts or other manufacturers” accessory parts are not guaranteed. Furthermore, BEFORE installing this product, make sure that all moving parts (e.g. the chain) are in the original state of maintenance. Installed accessories can change the driving behavior and/or stability of your vehicle.
GENERAL INFORMATION
Observe the country-specific regulations concerning vehicle registration/ operation as well as TOV regulations if applicable. If required, register installed parts in the vehicle documents through an appropriate inspection authority.
- PREPARATION: Read the mounting instructions carefully and make sure that all items on the parts list are included. Make sure that your vehicle is parked safely and cannot fall over. Turn off the engine and remove the ignition key. Let the motor/exhaust cool off if necessary. Disconnect the vehicle battery when working on the electrical system. Use appropriate tools. Have another person to help you.
- FUNCTION CHECK: After fixation also makes sure that no moving parts are obstructed and the function of the vehicle is not hindered in any way. Lamps as taillight and turn signals must not be limited in their function. Cables and hoses must not rub and/or be pinched. Before starting to ride, perform a comprehensive check of all functions.
- ATTENTION: Before riding and at each stop (every 200 km) check the proper fixation of the product!
- ATTENTION: Compatibility with accessory exhaust systems cannot be guaranteed!
All components of the product must not contact any hot or moving parts of the vehicle. All parts should also remain 5 cm away from hot parts of the vehicle and remain clear of the exhaust stream. For this reason, compress the suspension fully several times with your vehicle stationary.
PRODUCT SPECIFIC INFORMATION
- ATTENTION: Riding with this product may affect the motorcycles driving and braking performance! Cornering and ground clearance can be reduced by using this product!
- ATTENTION: Modifications will void any warranty.
ATTENTION: Not for off-road use
- SW-MOTECH GmbH & Co. KG
- Ernteweg 7-10 35282 Rauschenberg Germany
- Tel./ phone+ 49 (0)6425 / 8168 – 050
- Fax / fax+ 49 (0)6425 / 8168 – 10
- info@sw-motech.com
- www.sw-motech.com
PARTS LIST
Schritt
Step
| Nr.
No.
| Art. – Nr. / Bezeichnung a
Item No. / Description a
| Artikel| Part| Anzahlb
Quantit y b
| N· m ‘
---|---|---|---|---|---|---
■| | * _BC.HTA.OO.74O.3OOO_| PRO BLAZE® Satteltaschen| PRO
BLAZE® Saddlebags**| |
.13
.14
| 111| BC.ZUB.00.019.30000| Klickverschluss| Buckle| 2 /2|
131| LSF.350.250| Lackschutzfolie; 250 x 3 50 mm| Protection Foil; 250 x 3 50
mm| 212|
| | | | |
1| BC.HT A.00 .740.901.01 / 902.01| Satteltasche; links/ rechts| Saddlebag;
left/ right| 212|
| | | | |
1| BC.ZU B.00.0 64.30000| Wass e rd ichte lnnentasche| Waterproof l nn e rbag|
212|
| | | | |
■| | * _BC.HTA.OO. 74O.31OO_| PRO BLAZE® Satteltaschen hohe
Version| PRO BLAZE® Saddlebags high version**| |
.13
.14
| 111| BC.ZUB.00.01 9.30000| Klickverschluss| Buckle| 2 /2|
131| LSF.350.250| Lac ks chutz fol ie ; 250 x 350 mm| Protection Foil;
250 x 3 50 mm| 2 /2|
| | | | |
1| BC.HTA.00.740.901.02 / 902.02| Satteltasche; li nks / rechts| Saddlebag;
left/ right| 2 /2|
| | | | |
1| BC.ZU B.00.0 64.30000| Wasserdichte lnnentasche| Waterproof lnnerbag| 212|
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| Reg e lg ew in de / Coarse Thread 01 M4 I M5 I
M6 I MS I M10 I M12| | | Reg e lg ew in de /
Coa rs e Thread 01 M4 I M5 I M 6 **1
****MS I M10 I M12
Stahl FK 8.8 / Steel CL 8.8 N·m 2,8 5,5 9,6 23 46 79|
StahlFK10.9/SteelCL10.9 N·m** 4,1 8,1 14 34 67 115
Note: All measurements in millimeters. The second number indicates the
total quantity of the part in the delivery.
No. torque specifications: Use the torque defined by the vehicle
manufacturer! The standard torque in this table can be used as long as it is
within the vehicle manufacturer’s specifications.
FASTENING
- After mounting the saddlebags frames you need to protect the surface of the motorcycle against scratches with the included protection foil (2). Clean the surface from grease and dirt before applying the protection film.
- ATTENTION: Sharp edges have to be covered with several layers of the protection foil. After mounting the saddle bags, check if the affected parts of the vehicle are sufficiently protected against abrasion.
Slide the pannier sleeves of the saddlebags (3) on both sides onto the mounted support arms.
- Fasten the saddlebags |3) with the velcro flaps over the rear passenger seat) of the motorcycle, as shown in the drawing.
- ATTENTION: Make sure after loading the saddlebags (3) there is NO weight on the saddlebags frames! The weight of the saddlebags (3) must be supported by the velcro flaps, NEVER by the saddlebags frames. After loading, the saddlebag frames must be positioned in the saddlebag sleeves, as shown in the detailed drawing!
ATTENTION: Pay attention to the mounting instructions included in the saddlebag support arms! Fix the saddlebags [3] with the safety straps to the loosely mounted buckles [1] on both sides. Then tighten the screws of the buckles [1] as described in the mounting instructions of the saddlebag support arms.
Tighten the safety straps to secure the saddlebags
ATTENTION: Make sure BEFORE each ride that the velcro flaps and safety
straps of the saddlebags (3) are firmly tightened and there is NO weight on
the support arms! Wrong mounted saddlebags (3) can damage the product and
vehicle! Finally, roll up the excess salty strap length and secure it.
Use the waterproof inner bags (4) to protect your luggage from moisture. Additionally protect sensitive luggage [e.g., electronic equipment] from moisture with a plastic bag.
SAFETY, LOADING, AND CARE
- SAFETY AND LOADING: Make sure weight is evenly distributed between the saddlebags. Make sure that the loading is secured against shifting during the ride Do not store sharp or fragile objects ONLY loop assigned SW-MOTECH products to the MOLLE attachment
- ATTENTION: Remove the support arms when driving WITHOUT saddlebags from the vehicle! All components of the product must not contact any hot or moving parts of the vehicle. All parts should also remain 5 cm away from hot parts of the vehicle and remain clear of the exhaust stream.
- ATTENTION: Compatibility with accessory exhaust systems cannot be guaranteed!
- CARE: For cleaning use ONLY a soft textile brush, cloth, or sponge and warm soapy water! Rinse with clean water. Do NOT use strong cleaning agents, rough cleaning tools, or a high-pressure washer! Clean the product after riding in salty conditions, to avoid damage from salt.
- ATTENTION: Surface materials can experience color changes or fading when exposed to direct sunlight for extended periods of time and by environmental factors (e.g., SMOG, acid rain, etc.)! Gasoline and similar substances must be washed off immediately SW-MOTECH assumes no liability for color changes
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>