swemed JD 500 JSDA Nail Drill User Manual

June 4, 2024
swemed

JD 500
JSDA NAIL DRILL JD 500 
No.5870
No.5871
USER MANUAL DESCRIPTION

TECHNICAL SPECIFICATIONS

Control box JDS00 Handpiece
Weight: 960 g Weight: 160g
lnput voltage: AC 220V-240V Maximum rotation speed: 30000rpm
Frequency: 50Hz Power:35W
Output voltage: DC12V

 COMPOSITION KIT

1. nail drill;
2. handpiece;
3. pad for handpiece;| 5.box with cutters and caps (3x cutter, 1 x cap, 1 x mandrel).
---|---

OPERATION OF THE DEVICE

Operation af the device:

  • lnsert the handpiece flex plug(2), inta the power output socket on the main central machine (10),
  • Tum on/off using the Hand / OFF / Foot button (6)
  • Change the direction of rotation using the direction button FWD/REV(7)
  • The speed of rotation could be set max. to 35000rm by a speed control knob SPEED CONTROL MIN / MAX (8)

Functions:

  • The possibility of changing the direction of rotation;right or left
  • Easy changing level system; Turn on/off option by a footswitch ..

Using a footswitch option:

  • Connect the footswitch{4) with a footswitch connector in the device(11 );
  • Choose F option.FOOT” at the device (6);
  • Activate the device using SPEED CONTROL MIN/ MAX (8)
  • Regulate the operation of nail drill using a footswitch (4)

instructions:

  • Do not move the mode from S ta R in the handle, this action will cause the motor to seize, it will generate heat that may cause the handle to melt.
  • Before changing the direction of rotation, be sure that a cutter stops timing;
  • Do not keep too long the nail drill in cessation

THE ASSEMBLY OF THE CUTTER

  • In order to assemble or disassemble the cutter, hold a moving ring in the upper part of the handle. Next, tum clockwise, to full resistance (two limes) ATTENTION It may require force!
  • In order to block the cutter in the hand-holder, hold a moving ring in upper part of the holder. Next, tum full counter-clockwise (two times).
    ATTENTION it may require force!

swemed JD 500 JSDA Nail Drill - Handle

instruction:

  • Wash the handpiece and cutter before the assembly;
  • During changing the holder/ cutter disconnect the device from the power source;
  • During the installation of the cutter, it should be settled in a warhead of the handle(till it stops);
  • After changing and saving the cutter in the warhead of handle, check if it works;
  • Do not unscrew the handle if the device works;
  • Never use curved,asymmetric and damaged cutters!
  • After a long term of non-use of the device, it is necessary te check if it works.

 TECHNICAL DATA OF DIFFERENT CUTTERS

swemed JD 500 JSDA Nail Drill - CUTTERS

**PRECAUTIONS

**

Read the manual in order to prevent accidents.

  • In order to ensure a long life span of the nail drill work with using the footswitch.
  • Use the device in temperatures 0-4-0oC
  • Using the device in a dusted, heated, and wet environment may damage it;
  • Do not use the device with wet hands;
  • Do not use the device if the cord is damaged;
  • Do not connect too many devices to the same power source/ socket;
  • Do not assembly and modify the device on your own;
  • De not allow the device and the handle of the device wih contact with water and other liquids;
  • Work with a device carefully, for the customer’s safety;
  • Do not use and keep the device in high temperature and on exposure of the sun;
  • Before using the device, check the device in an appropriate distance from the customer (check slack, vibration, evaluate sound and temperature);
  • During the operation, put the handle in an appropriate rack or holder;
  • Connect the device with the proven source of power with an appropriate voltage(220-240V).
  • Recommended operation of the device is an intermittent mode in order to failure-free operation.
  • During the work with nail drill always use goggles and a protective mask
  • lf the disconnected power cord is damaged, it should be changed only in the manufacturer’s company or by an employee of the service or by a qualified person in order to prevent the risk.

TROUBLESHOOTING

Problem Checkpoint Solution
The engine does not work One of the cords is disconnected Check the

connection of cords
The damage of one of the cords| Replace the cord
Problem with the engine| Check the engine/or send the footprint to
the service
The engine suddenly does
not work| Congestion or the handle open during work| Read about the safety system, check the
handle
The motor does not work by
using a footswitch| The damage of the footswitch| Switch the changing button inter
The damage of the plug| Change/send the footswitch to service
Disconnection of the cord| Check the connection
The device is disconnected| Check the button

Please report failures to the distributor

Documents / Resources

| swemed JD 500 JSDA Nail Drill [pdf] User Manual
JD 500, JSDA Nail Drill, JD 500 JSDA Nail Drill, Nail Drill, Drill
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals