PIT PSW1100-W2 Fecal pump, 1100 W, with knife, pressure Instruction Manual

PIT PSW1100-W2 Fecal pump, 1100 W, with knife, pressure

Safety Instructions

General Power Tool Safety Warnings

WARNING Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.
Retain these instructions and directions for future use.
ATTENTION!

• Do not use the product without protec-tive grounding!
• Installation of a residual current device (RCD) with a rated leakage current of 30 mA is mandatory!
• The installation of the product and the electrical outlet for connecting it to the mains must be carried out by qualifi ed electricians.
•  To avoid accidents, it is strictly forbid-den to carry out any repair / mainte-nance work on the equipment without disconnecting it from the electrical net-work.
• The product is intended for pumping ONLY fresh water. DO NOT use the pump for pumping salt water, solvents, corrosive, flammable or explosive liq-uids, liquid food, faeces.
• Do not allow the pump to run dry (with-out water intake) and / or with a blocked supply channel.
• Do not block the water intake holes of the product.
• To avoid product damage, DO NOT turn ON or USE the product at temperatures below 1 ° C, and do not leave it working overnight if frost is possible.
• The pump is cooled by the surrounding water. Therefore, do not operate the product outside of water and do not use in bodies of water or tanks with water temperatures above 35 ° C.
• Do not repair or disassemble the prod-uct yourself.

Electrical safety
ATTENTION! If the safety instructions are not followed, there is a risk of electric shock.

• The product is intended for use in FULL immersion. Observe the condition of the insulation of the network cable, do not damage the insulation.
• When connecting the product to the mains power supply, use only grounded electrical outlets to avoid electric shock.
• Unsuitable electrical cables and cables can be hazardous. Outdoors, use only approved and appropriately marked exten-sion cords with sufficient wire cross-sec-tion.
• Do not use the mains power cable to transport or fi x the instrument.
• When disconnecting the appliance from the mains supply, do not pull on the plug, not on the cable.
• Be careful not to pinch the power cord or rub it against sharp edges.
• Install the device in a stand-up and overfi ll-proof position.
• The mains voltage must correspond to the voltage specified in the technical specifi cations.
• DO NOT use the pump in water bodies (ponds, pools), where people are or may be, and it is also forbidden for peo-ple to be in a water body with the pump running.
• Electrical connections must only be made by a qualifi ed electrician.

Safety of people

• For safety reasons, persons under the age of 16 or those who have not read this manual must not be allowed to work with the device.
• The pump is not intended for use by persons with reduced physical or men-tal capabilities or lack of experience and knowledge of the user, unless he is supervised and instructed in the use of the device by a person responsible for safety.
• It is forbidden to operate and service the pump while in a state of extreme fatigue, alcoholic, drug intoxication or under the influence of strong medica-tions.
• Children and pets should not be near the pump when it is running. Children should be supervised to ensure that they do not play with the device.

Safety instructions for working with the pump

• Any use of the pump in violation of the rules of its operation is considered as use for other purposes. Damage result-ing from use for other purposes is the sole responsibility of the user.
• The pump is not intended for professional or industrial use. Long-term con-tinuous use is not allowed.
• Unauthorized modifi cations to the pump design, as well as the use of parts that have not passed the tests and are not approved for use by the manufacturer, are prohibited.
• It is forbidden to pump explosive, fl am-mable, corrosive or health hazardous substances, as well as water containing mechanical impurities in the form of sand, stones, etc.
• The pump is not suitable for pumping chlorine-containing water in swimming pools.
• Not recommended for pumping drink-ing water.
• When starting the pump for the first time, ensure that it is completely fi lled with water. it is not allowed to operate the pump without water consumption.
• Air entering the suction line is not al-lowed.
• To avoid freezing, the water must be completely drained from the pump and from the suction and pressure lines.

Description of product and services

Read all safety instructions and in-structions.
Failure to follow the safety instructions  and instructions can result in electric shock, fi re and / or serious injury. Please observe the illustrations at the begin-ning of the operating instructions.

Intended use

The pump is designed for pumping clean and dirty water. It can be used for pumping water from reservoirs, organizing water intake from a depth (wells) and supplying it to a height, to protect basements and other premises from fl ooding; for drainage of reservoirs, reservoirs, pits and use in aeration and drainage sys-tems, taking into account the technical char-acteristics of the model.
The product is not intended for continuous operation (continuous pumping mode).

Product Features

The numbering of the product features refers to the diagram of the power tool on the graph-ics page.

1. Water inlet
2. Pump housing
3. Handle
4. Float switch
5. Water inlet pipe
6. Network cable

Technical Data

Contents of delivery

• Sewage Pump 1 pc .
• Float switch 1 pc .
• Instruction manual 1 pc .

Note In text and numbers, may technical errors and mistakes were made Since the product is constantly being improved, P.I.T. reserves the right to make changes to the specifications and equipment of the product specifi ed here without prior notice.

Preparation for work

• Connect a hose to the water inlet(5). Fasten it securely with a hose clamp. It is recommended to use a flexible hose (pressure hose) with a diameter corre-sponding to the water inlet as a hose.
• If necessary, attach the cable or cable to the handle(3);
• Check that all connections are secure.
• Lower the pump into the water while holding it by the rope. Secure the cable.
• Water should not leak out anywhere. The tightness of the connections directly aff ects the pump performance.

The maximum head – is the maximum height of water rise from the pump at its maximum allowable submersion.
Maximum capacity – is the maximum possi-ble amount of water pumped by the pump per unit of time.
An increase in the number of adapters, kinks and a decrease in the diameter of the nozzles reduces the head and productivity.

Exploitation

The submersible drainage pump is designed to operate under water at a depth of 5 me-ters at temperatures from +1°C to +35°C in a place with a low level of pollution.
ATTENTION! Every 15 minutes of continuous operation of the pump, it is necessary to take a break for 10-15 minutes.

• Make sure that the network parameters correspond to the parameters indicated on the pumping equipment and in this operat-ing manual.
• Make sure that the pumping equipment will be connected to the mains through a residual current device with a rated operat-ing current ≤ 30 mA.

Adjust the length of the fl oat switch wire by at-taching the wire to the hole in the pump body. This allows you to adjust the immersion depth and the automatic cut-off depth.
If the water level falls below the level of the fl oat switch, the pump will shut off . This pro-tects the pump from running dry.
The float switch can be forcibly locked in order to pump liquid to the level of the water intake holes.
Fasten the float switch vertically in the slots on the pump housing.
Make sure that the intake holes are always covered with water. Otherwise, if the water runs out and the pump runs dry, the pump parts will wear out quickly and the pump may fail.

• Place the pump on a fi rm, clean (no draft) base or, if depth permits, hang it from the carry handle using a rope or cable (sold separately). Do not suspend the pump by the power cable. The free space around the pump should be at least 50×50 cm. When the pump is fi rst immersed in water, tilt it, so you remove air from the water intake part. Otherwise, the initial start-up of the pump will be diffi cult due to the air lock.
• Connect the plug of the mains cable to the mains. Check the process of pumping wa-ter.

ATTENTION! If the water level is too low, when the pump is turned off, any dirt inside the pump will dry out quickly. This can result in the pump not starting when the water level rises. To ensure effi cient pump operation, reg- ularly clean the bottom of the shaft to remove any debris.

Auto mode
In automatic mode, a fl oat switch controls the operation of the pump.
In order for the pump to start working in auto-matic mode, lower it into water, connect the mains cable plug to the mains. The pump will run until the fl oat switch reaches the minimum depth required to shut off . It is recommended to install the pump on a solid base to maintain an upright position. After diving, make sure that the fl oat switch is not obstructed. ATTENTION! The pump must be lowered to a depth using a cable tied to the handle. Never immerse the pump in water using the mains cable.

Manual mode
For manual operation, the motor can be start-ed by lifting the float switch by hand. Lower the fl oat switch to turn off the pump. ATTENTION! During manual operation, do not leave the pump unattended; working with-out water will damage it.

End of work
After use, run clean water through the pump for 2-3 minutes in order to get rid of sediment and particles that may accumulate in the pump or outlet hose.
Disconnect the mains cable from the mains, remove the pump from the water and move it to a dry ventilated area.

Storage and maintenance
Be sure to flush the pump with clean water after each use.

Storage
With prolonged inactivity of the fecal pump, as well as in winter, storage must be carried out in a dry, heated room. First, it is necessary to drain the remaining water from it and pipes, rinse with clean water and dry.
The pump does not require preservation. It should be stored at temperatures between + 1 ° C and + 35 ° C, away from heating devices and avoiding direct sunlight.

Transportation
Products can be transported by any type of closed transport in the manufacturer’s pack-aging or without it, while preserving the product from mechanical damage, atmospheric precipitation.

Service

Have your power tool repaired only by quali-fi ed personnel and only with original replace-ment parts. This ensures the safety of the power tool. The list of authorized service centers can be found on the official website of P.I.T. by the link: https://pittools.ru/servises/

Dispose of waste

Damaged power tools, batteries, acces-sories and waste packaging materials must be recycled and reused in an environmentally friendly manner.
Do not throw power tools and accumulators / batteries into general household waste!

Product serial number interpretation

The first and second digits of the product seri-al number from left to right Year of production, the third and fourth digits indicate the month of production, the fi fth and sixth digits indicate the production day.

TERMS OF WARRANTY SERVICE

1. This Warranty Certifi cate is the only docu-ment that confi rms your right to free warranty service. Without presenting this certifi cate, no claims are accepted. In case of loss or dam-age, the warranty certifi cate is not restored.

2. The warranty period for the electric ma-chine is 12 months from the date of sale, during the warranty period the service depart-ment eliminates manufacturing defects and replaces parts that have failed due to the fault of the manufacturer free of charge. In the war-ranty repair, an equivalent operable product is not provided. Replaceable parts become property of service providers. P.I.T is not liable for any damage that may be caused by operation of the electric machine.

3. Only clean tool accompanied with the following duly executed documents: this War-ranty Certifi cate, Warranty Card, with all fi elds fi lled out, bearing the stamp of the trade orga-nization and the signature of the buyer, shall be accepted for warranty repair.

4. Warranty repair is not performed in the following cases:

   • in the absence of a Warranty Certifi cate and a Warranty Card or their incorrect execution;
   • with failure of both a rotor and a stator of the electric engine, charring or melting of primary winding of the welding machine transformer, charging or starting-charging device, with in-ternal parts melting, burn down of electronic circuit boards;
   • if a Warranty Certifi cate or a Warranty Card does not correspond to this electric machine or to the form established by the supplier;
   • upon expiration of the warranty period;
   • at attempts of opening or repair of the elec-tric machine outside the warranty workshop; making constructive changes and lubrication of the tool during the warranty period, as ev-idenced, for example, by the creases on the spline parts of the fasteners of non-rotational parts.
   • when using electric tools for production or other purposes connected with making a prof-it, as well as in case of malfunctions related to instability of the power network parameters exceeding the norms established by GOST;
   • in the events of improper operation (use the electric machine for other than intended pur-poses, attachments to the electric machine of attachments, accessories, etc. not provided by the manufacturer);
   • with mechanical damage to the case, pow-er cord and in case of damages caused by aggressive agents and high and low tempera-tures, ingress of foreign objects in the ven-tilation grids of the electric machine, as well as in case of damage resulting from improper storage (corrosion of metal parts);
   • natural wear and tear on the parts of the electric machine, as a result of long-term op-eration (determined on the basis of the signs of full or partial depletion of the specified mean life, great contamination, presence of rust outside and inside the electric machine, waste lubricant in the gearbox);
   • use of the tool the purposes for other than specifi ed in the operating instructions.
   • mechanical damages to the tool;
   • in the event of damages due to non-obser-vance of the operating conditions specifi ed in the instruction (see chapter “Safety Precau-tions” of the Manual).
   • damage to the product due to non-obser-vance of the rules of storage and transporta-tion. Preventive maintenance of electric machines (cleaning, washing, lubrication, replacement of anthers, piston and sealing rings) during the warranty period is a paid service.
     The service life of the product is 3 years. Shelf life is 2 years. It is not recommended for oper-ation after 2 years of storage from the date of manufacture, which is indicated in the serial number on the label of the instrument, without preliminary verifi cation (for the defi nition of the date of manufacture, see the User’s Manual earlier).
     The owner is notified of any possible viola-tions of the above terms of wa rranty service upon completion of diagnostics in the service center.
     The owner of the tool entrusts the diagnostic procedure to be conducted in the service cen-ter in his absence.
     Do not operate the electric machine when there are signs of excessive heat, sparking, or noise in the gearbox. To determine the cause of the malfunction, the buyer should contact the warranty service center.
     Malfunctions caused by late replacement of carbon brushes of the engine are eliminated at the expense of the buyer.

5. The warranty does not cover:

   • replacement accessories (accessories and components), for example: batteries, discs, blades, drill bits, borers, chucks, chains, sprockets, collet clamps, guide rails, tension and fastening elements, trimming device heads, base of grinding and belt sander ma-chines, hexagonal heads, etc.,
   • fast wearing parts, for example: carbon brushes, drive belts, seals, protective covers, guiding rollers, guides, rubber seals, bear-ings, toothed belts and wheels, shanks, brake belts, starter ratchets and ropes, piston rings, etc. Their replacement during the warranty period is a paid service;
   • power cords, in case of damage to the insu-lation, power cords are subject to mandatory replacement without the consent of the owner (paid service);
   • tool case.

P.I.T. WARRANTY CERTIFICATE

• Product Name_____
• Product Serial Number □□□□□□□□□□□
• Charger Serial Number □□□□□□□□□□□□□
• Sale Date __
• Trade Organization Name __

Dear customer!
Thank you for purchasing the P.I.T. tool, and we hope that you will be satisfi ed with your choice. In the process of manufacturing the P.I.T. tools pass multilevel quality control, if nevertheless your product will need maintenance, please contact the authorized P.I.T. service centers. Attention!
When buying, ask a seller to check the completeness and operability of the tool, to fi ll out the Warranty Certifi cate, the Warranty Card (the boxes shall be fi lled out by a seller) and to affi x the seal of the trade organization in the Guarantee Certifi cate and the Warranty Card.
Warranty
By this Warranty Certifi cate, P.I.T. company guarantees the absence of defects of the production nature.
In the event any of the above defects are detected during the warranty period, the specialized P.I.T. service centers shall repair the product and replace the defective spare parts free of charge.
The warranty period for P.I.T. electric machines is 12 months from the date of sale.
“The warranty maintenance terms acknowledged and accepted. The operability and complete-ness of the product are checked in my presence. No claims on quality and appearance.”
Buyer’s Signature___ Surname (legibly) __
Phone __

P.I.T. WARRANTY CARD

[email protected]

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>