RIGHT WEIGH RTK-01/-02 Remote Sensor Kit for 201 Series Gauges Instruction Manual
- June 3, 2024
- Right Weigh
Table of Contents
INSTALLATION
Installation Manual
REMOTE SENSOR KIT
For 201 Series Gauges | RTK-01/-02
RTK-01/-02 Remote Sensor Kit for 201 Series Gauges
IMPORTANT!
Please read instructions COMPLETELY and thoroughly before installation. Right
Weigh, Inc. is not responsible or liable for product failure or vehicle damage
due to improper installation. The installation requirements are outlined in
this manual and should be followed thoroughly to avoid inaccuracy or damage to
the product.
It is also important to be aware of vehicle manufacturer policies before
making modifications to the vehicle. Right Weigh, Inc. is not liable or
responsible for issues regarding warranties with other manufacturers. This is
the responsibility of the customer. If you are unsure about how these
installation practices apply to your vehicle, please contact your vehicle or
component manufacturer.
PARTS INCLUDED:
HARDWARE INCLUDED:
| 6. 2 x 5/16” Mounting Bolt | 11. 4 x 3/8-16 Nylon Insert Lock Nut |
|---|---|
| 7. 2 x 5/16” Flat Washer | 12. 1/4” NPT Street Tee Fitting |
| 8. 2 x 5/16” Nylon Insert Locknut | 13. 3/8” NPT Street Tee Fitting |
| 9. 4 x 3/8-16 Hex Cap Screw | 14. 3/8” NPT to 1/4” NPT Reducer Fitting |
| 10. 8 x 3/8” Flat Washer | 15. 1/4” NPT to 1/4” Tube Fitting |
A LOCATE MOUNTING BRACKET ONTO TRAILER
Locate the mounting bracket to the front of the trailer where it is accessible to the driver using the supplied hardware. Please use all 4 mounting locations on the bracket to fully secure the system to the trailer.
Once the mounting bracket is secure on the trailer, mount the data communication socket to the bracket using the supplied hardware.
B INSTALL AIR LINE AND CONNECT TO AIR BAG(S)
Using the supplied hardware, tee into the any air bag connected to the axle group being measured. Run 1/4” air line from the air bag to the remote sensor. Use the provided zip ties to hold the air line in place. Connect the air line to the push-to-connect fitting on the back side of the remote sensor.
Trailer with 2 HCV
Repeat this process for a trailer axle group with 2 HCV. Tee into a second air
bag on the trailer axle group that is connected to the second HCV. Using the
provided air line and zip ties, run the air line to the remote sensor and
connect to the second push-to-connect fitting. It does not matter which fitting
each go into as long as there is an air line connection to an air bag
connected to each HCV on the trailer axle group to accurately measure the
weight.
THANK YOU FOR YOUR BUSINESS
Thank you for choosing to drive more and scale less! Here at Right Weigh, we
are committed to making our products simple to install and easy to use. We
understand that installation can vary between vehicles and yours may not be
described in this manual. In any event, our technical support team is ready to
answer your questions!
CONTACT US FOR ADDITIONAL SUPPORT
United States and Canada:
Right Weigh, Inc. 503-628-0838
888-818-2058 – Toll Free (USA ONLY)
www.rwls.com
support@rwls.com
Australia and New Zealand:
Smart Truck Solutions
+61 418 622840
rightweigh.com.au
| RightWeighInc | rightweigh_inc | rwlsinc | right-weigh-inc- |
|---|
Right Weigh, Inc.
Hillsboro, Oregon USA
©2015-2021 Right Weigh, Inc. All rights reserved.
PP-003-0085 Revision A
October 2021
References
- On-Board Truck Weight Scales & Weight Gauges | RIGHT WEIGHâ„¢
- Manuals & Resources - Right Weigh
- Right Weigh | Onboard Load Scales
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>