PATLITE ME-A LED Signal Light Instruction Manual

PATLITE ME-A LED Signal Light Instruction Manual

Notice to Customer Thank you very much for purchasing our Patlite products.

• This product requires installation, wiring, and other related work, Be sure to ask an expert technician to perform these procedures,
• This installation manual is intended for the technician who performs the installation and wiring of the product.
• A separate user’s manual is provided for customers who operate the product after installation. Be sure to read the user’s manual before operating the product

WARNING
Indicates an imminently dangerous condition: failure to follow the instructions may lead to death or serious injury.

• Request the installation and wiring to be accompanied by a professional contractor. If installation is done improperly, it may result in fire, electric shock,

CAUTION
Indicates a potentially dangerous condition: failure to follow the instructions may lead to slight injury or property damage.

• Use a soft cloth dampened with water to clean the product. (Do not use thinner, benzine, gasoline or oil.)

**** Warning

• Do not use this product with melera damaged or moved or without the head in oder 30 wold an electic shock,
• When this purposes, it shoutenplaat you wheth
• Donuts the product to support your waghtening ramathep to the isorofyachiner

Caution

• Concerning replacement parts, such as LED unit, bulb or fuse, be sure to use those specified in this manual.
• For safety, make sure to connect an extemal fuse to the power source as shown in the wiring example.
• Do not substitute parts from other products as this may cause a breakdown.

Caution

• Concerning replacement parts, such as LED unit, bulb or fuse, be sure to use those specified in this manual.
• For safety, make sure to connect an external fuse to the power source as shown in the wiring example.
• Do not substitute parts from other products as this may cause a breakdown.

Model Number Configuration

ME-A Type ME-A
MP /Type MP

Part Names and Outer Appearance

**ME-A/Type ME-A
(Part Names)

(Dimensions)

MES-A/Type MES-A
ME-A/Type ME-A
ME-A/Type ME-A
**

**Ground Housing

**

**MP/Type MP
(Part Names)

**

**(Dimensions

MPS/Type MPS

MP/Type MP
Optional Parts L bracket (Model SZL-001
**

Installation

The following requirements are necessary for proper installation.

• * Install where no excessive vibration is present.

  • Install on a strong surface,
  • Install in an upright position, (Do not install the Signal Tower sideways or inverted.)
• This product can only be used indoors. (Do not use outdoors.)
• When installing this product, do not use excessive torque, or the product may be damaged.
• During installation, do not remove the waterproof sheet, it will increase possible water  penetration and may cause a malfunction. (Type MP only)

How to Install

ME-A/Type ME-A
The possible thickness of the installation plate is 10 mm or less.

1. Turn nut three threads (5 mm) or more.

2. Hold nut in one hand and tighten nut 2 with the other hand as far as the plate surface.

3. Hold nut 1 using an 24 spanner, and tighten nut 2 using an 27 spanner.

MP Type MP

*The possible thickness of the installation plate is 5 mm or less.

Mounting Dimension

1. Install the waterprood sheet 2 in the body, and through the mounting hole.

2. Please use the washer and the Hex, nut for installation. (Fasten it with the torque of 3.5±0.5N-m.)

Caution

• Make sure the power is OFF before wiring. A short circuit may damage internal circuits or cause an electric shock.
• Enough attention shall be paid for wiring because if there is any mistakes in wiring a circuit may break down.
• Install the external contact fuse on the power supply side as shown in the wiring example in order to prevent burn in case of a wiring error.
• Do not pull out the lead wire or push it into the body.

How to perform wiring

• Maike wiring connection according to wiring example,
• When wiring 5 layers or less, please make wiring connection by increasing or decreasing external contacts in each layer according to wiring example,
• When using LED units of the same color, calculate the contact curent capacity to be equal to the number of the LED units multiplied by the contact capacity for 1 light. (This is because current passee through one  signal Iine for the multiple LED units of the same color.)
• When wiring is completed, insudate the end of each unused lead wire with insulation tape.
• Any questione regarding applications for multiple units, or other special operations, contact your nearest PATLITE Sales Represeritative before wiring. To be recognized as a UL, standard.
• Fuse for protection of axtarmal contact should be installed within 305mm from the connected point of the power source wine,
• Use a Class 2 Circuit for the power supply source and be sure to use the fuse and fuseholders authorized by UL,
• Use the fuse conforming to the rated current of the machine which the product was installed on. (Example: Class J type fuse)

Wiring Example

*All 5 wires (Red, Orange, Green, Blue, White) are connected regardless of the number of LED units.
External Contact (Transistor) Capacity

Is: Current Capacity, Vs: Withstand Voltage, IL: Leakage Current

**External Fuse

**

Fuse Rating
250V 1A
Use the fuse conforming to the rated current of the machine which the product was installed in. (Example: Class J type fuse)

(NPN(PNP)Transistor drive example) ※Model ME-A : NPN type only

PNPTransistor (Type MP only)

Changing LED Unit positions

  Caution

• Maka sure the power is off before wiring to avoid a short-circuit, electric shock, or bum.
• Do not remove the LED unit forcibly as it may damage the unit.
• When the center screw is loosened or removed, the LED units become unstable and may separate, Therefore, handle carefully to avoid damage.
• Handle the LED units carefully to avoid warping or damage when changing their positions on the tower.
• Screwing the head cover too tight may damage it. The recommended torque is about 0.6N-m.

Changing LED Unit positions

• Turn the power off before changing LED unit positions.

• Unscrew the head cover and remove the LED unit.

• The upper and lower LED units are secured to align the marks on the lens surface. (Type ME-A>PC<, Type MP:>SAN<.)

• When you join the bottom LED unit with the body, make sure the center of the LED unit is aligned with the chassis in the center of the body.
  (Make sure the marks on the lens surface is facing the same direction as the name plate. (Type ME-A>PC<, Type MP:>SAN<.))

• When changing the number of modules, install a center screw to match the number of tiers.

With marks (Type ME-A:>PC<, Type MP:>SAN<.) aligned between the upper and lower units, press the two parts straight together.

Specifications

IME-A Type ME-A

Tiers| Model| UL Registration Model| Rated Voltage| Power Consumption| Mass| Wire type/Diameter
---|---|---|---|---|---|---
1 Tier| ME-102A| ME-_02A| DC 24V24V DC| :0.60W
0.32W
Red Amber:0.60WGreen Blue White: 0.32W| 0.22kg| UL1007/AWG22
MES-102A| MES-02A| 0.12kg
2Tier| ME-202A| ME- 02A| 0.23kg
MES-202A| MES-_02A
3 Tier| ME-302A| ME- 02A| 0.13kg
MES-302A| MES-02A| 0.24kg
4 Tier| ME-402A| ME- 02A
MES-402A| MES-_02A| 0.14kg
5 Tier| ME-502A| ME- 02A| 0.25kg
0.15kg
MES-502A| MES- 02A| 0.26kg
0.16kq

MP Type MP

Tie rs| Model| UL Registration Model| Rated Voltage| Power Consumption| Mass| Wire type/Diameter
---|---|---|---|---|---|---
1 Tier| MP-102| MP-_02| AC/DC 24V
24V AC/DC (50/60Hz)| ::0.70W :0.71W 0.41W Red :0.70W
Amber :0.71W
Green Blue White: 0.41W| 0.21kg| UL1007/AWG22
MPS-102| MPS-_02| 0.11kg
2Tier| MP-202| MP-02| 0.23kg
MPS-202| MPS-_02
3 Tier| ME-302A| MP-02| 0.13kg
MP-302| MPS-02| 0.25kg
4 Tier| MPS-302| MP-02
MP-402| MPS- 02| 0.15kg
5 Tier| MP-502| MP-02| 0.27kg
0.17kg
MPS-502| MPS- 02| 0.29kg
0.19kg

User Manual

Notice to Customer Thank you very much for purchasing our Patlite products.

• This product requires installation, wiring, and other related work. Be sure to ask an expert technician to perform these procedures.
• Read this manual thoroughly before using this product to ensure correct use.
• If there are any questions concerning this product, refer to the contact information at the end of this document and contact your nearest PATLITE Sales Representative.
• This product has been tested and found to comply with the limits for a Class A device.
• These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
• This product must not be used in residential areas.

  WARNING Indicates an imminently dangerous condition: failure to

follow the instructions may lead to death or serious injury.

• Request the installation and wiring to be accompanied by a professional contractor. If installation is done improperly, it may result in fire, electric shock, falling, or malfunction,
• Be sure to disconnect the power to the product when performing maintenance or repairs. If the power is not disconnected, a may result in electric shock.

CAUTION Indicades a potentially dangerous condition: failure to

follow the instructions may lead to skure injury or property damage

• Use a soft cloth dampened with water to clean the product. (Do not use thinner, benzine, gasoline or oil.)

Warming

• Do nat use this product to support your weight while clkeriting anta a machos Moure the product so that it is clear of any marving parts-such as a machine
• The images in this manual may vary in comparison to the actual product and are only for the purpose of illustration.
• Specifications may change without notice due to continual product improvement.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>