RAB CRLEDFA Series Recessed Commercial Downlight FA Instructions

RAB CRLEDFA Series Recessed Commercial Downlight FA

IMPORTANT

READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAINTHESE INSTRUCTIONS FOR FUTURE REFERENCE.

RAB fixtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper grounding is required for safety. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.

WARNINGS:

• Risk of electrical shock. Disconnect power at fuse or circuit breaker before installing or servicing.
• To prevent early lamp failure, lamp should only be installed in operating environments ranging between-30°C and +40°C (-22°F and+104°F).
• No user serviceable parts inside. To avoid electrical shock do not disassemble product.
• Risk of fire or electric shock, LED Retrofit Kit installation requires knowledge of luminaires electrical systems. If not qualified, do not attempt installation. Contact a qualified electrician.
• Risk of fire or electric shock, Install this kit only in luminaires that have the construction features and min dimensions shown in below and where the input rating of the retrofit kit does not exceed the input rating of the luminaire.
• Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation
• To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.
• Installers should not disconnect existing wires from lamp holder terminals to make new connections at lamp holder terminals, Instead installers should cut existing lamp holder leads away from the lamp holder and make new electrical connections to lamp holder lead wires by employing applicable connectors.
• The retrofit kit is accepted as a component of a luminaire where the suitability of the combination shall be determined by authorities having jurisdiction. Product must be installed by a qualified electrician in accordance with the applicable and appropriate electrical codes. The installation guide does not supersede local national regulations for electrical installations.
• This device is not intended for use with emergency exits.
• Caution – risk of fire. Consult a qualified electrician to ensure correct branch circuit conductor
• Min.90°C supply conductors.
• Installers should examine all parts that are not intended to be replaced by the retrofit kit for damage and replace any damaged parts prior to installation of the retrofit kit.

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

WHAT’S IN THE BOX

• Downlight (1)

• MC connector (1)

• Wire Nuts (5)

• Lumi Sticker (1)

• Template (1)
  

TOOLS NEEDED

This LED Recessed Kit requires very few tools for installation. A screwdriver and a pair of wire cutters will help to install the down light to a Box or housing.

OPTIONAL ACCESSORIES

Goof Ring

• DL4-6GOOF/R/P/CRLEDFA
  For use with 6″ ceiling hole applications

• DL6-8GOOF/R/P/CRLEDFA
  For use with 8″ ceiling hole applications

• DL8-10GOOF/R/P/CRLEDFA
  For use with 10″ ceiling hole applications

• DL8-12GOOF/R/P/CRLEDFA
  For use with 12″ ceiling hole applications

• DL10-12GOOF/R/P/CRLEDFA
  For use with 12″ ceiling hole applications

Plate

• DLPLATE/C3468R/NB
  Mounting plate with nailer bar

Frame

• DLFRAME/C6R
  

• DLFRAME/C8R
  

INSTALLATION WITH EXISTING FRAME

1. Shut power OFF to the fixture.

2. Remove CFL, Incandescent or HID lamp. (Fig.1)
   

3. Remove reflector from rough-in(mounting frame). (Fig.2)
   

4. Remove socket assembly from reflector. (Fig.3)
   

5. Remove J-Box metal plate with existing lamp ballast. Do not dispose. Disconnect all wires from the ballast. (Fig.4)
   

6. Remove the existing lamp metal conduit (MC) cable from the J-Box. (Fig.5)
   

7. Select desired lumen and CCT level using switch on driver box. (Fig.6)
   

8. Fasten the LED retrofit kit MC cable to the J-Box. (Fig.7)
   

9. Wire nut the ground (green) wire in the junction box. Wire nut the black input wire with the black wire from the MC cable and wire nut the white input wire with the white wire from the MC cable. Wire nut the purple input wire with the purple wire from the MC cable and wire nut the pink input wire with the pink wire from the MC cable. If the purple and pink wires are not in use, cap these with wire nuts. (Fig.8)
   

10. Install the junction box cover plate (with lamp ballast still attached to it). (Fig.9)
    

11. Install the retrofit kit in the rough-in by lifting upward both retention tabs. Push the kit until it sits flush against the ceiling. ( Fig.10)
    

12. Turn power ON and start saving $$.

INSTALLATION WITHOUT EXISTING FRAME

1. Use template inside box to cut hole in ceiling. (Fig.11)
   

2. Select desired lumen and CCT level using switch on driver box. (Fig.12)
   

3. Shut power OFF to the fixture. Fasten the LED kit MC cable to a junction box with MC connector. Wire nut the ground (green) wire in the junction box. Wire nut the black input wire with the black wire from the MC cable and wire nut the white input wire with the white wire from the MC cable. Wire nut the purple input wire with the purple wire from the MC cable and wire nut the pink input wire with the pink wire from the MC cable. If the purple and pink wires are not In use, cap these with wire nuts.(Fig.13)
   

4. Install junction box cover plate. (Fig.14)
   
   Note: These instructions do not cover all details or variations in equipment nor do they provide for every possible situation during installation, operation or maintenance.

5. Install the LED kit by lifting both retention tabs upward. (Fig.15 )
   

6. Push the kit until it sits flush against the ceiling. (Fig.16)
   

INSTALLATION WITH EMBB

Take the Emergency Battery Backup System and snap in the MC cable from the EMBB into the J-Box. Fasten the LED retrofit kit MC cable to the J-Box. In the J-box, use wire nuts to do the wire connections as illustrated in the diagram below. Make sure EMBB is grounded. Please visit rablighting.com for EMBB information.

MIN.LUMINAIRE DIMENSION

DIMENSIONAL DAWINGSR

Easy Answers

rablighting.com
Visit our website for product info

Tech Help Line
Call our experts: 888 722-1000
e-mail
Answered promptly – sales@rablighting.com
Free Lighting Layouts
Answered online or by request

RAB WARRANTY: RAB’s warranty is subject to all terms and conditions found at rablighting.com/warranty.

References

• Welcome to RAB
• Legal - RAB Lighting

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>