Breville LAP300 Smart Air Purifier Instruction Manual

: June 2, 2024
: Breville

**the Smart AirTM Purifier

**

Instruction Book – LAP300

BREVILLE RECOMMENDS SAFETY FIRST

At Breville we are very safety conscious. We design and manufacture consumer products with the safety of you, our valued customer, foremost in mind. In addition, we ask that you exercise a degree of care and adhere to the following precautions.

SPECIFICATIONS

Filter Life: Approx. 6 months
Microbe ShieldTM Life: Approx. 10,000 hours
Product Dimension: 231 x 391mm
For Room Size: 30 to 40m²
Noise Level: 30~60dB
Power Consumption: 30W
Weight : 4kg

IMPORTANT SAFEGUARDS

READ ALL INSTRUCTIONS BEFORE USE AND SAVE FOR FUTURE REFERENCE:

Remove and safely discard any packaging material and promotional labels before using the air purifier and filter for the first time.
To eliminate a choking hazard for young children, remove and safely discard the protective cover fitted to the power plug of this air purifier.
When unpacking the air purifier, check to see you have received all the items listed in the parts list, before discarding the packaging.
This air purifier is intended for household use only and not for commercial or industrial use.
Do not use outdoors.
Always ensure the air purifier is properly assembled before use. Follow the instructions provided in this book.
Do not place the air purifier near the edge of a bench or table during operation. Ensure the surface is level, clean and free of water.
Keep the power cord out of heavy traffic areas. To avoid fire hazard, never put the cord under rugs, near heat registers, radiator, stoves or heaters.
To protect against electrical hazards, do not immerse in water or other liquids. Do not use the air purifier in the immediate surroundings of a bath, a shower or a swimming pool.
Children should be supervised to ensure they do not play with the air purifier.
Always turn off and unplug the air purifier before moving, opening the grill, changing filters, cleaning or whenever the air purifier is not in use.
Do not unplug the air purifier by pulling on the power cord. Always unplug using the power plug.
Never insert fingers, pencils or any other objects through the guards whenever the power plug is connected, in particular, while the air purifier is switched on.
Do not run the power cord under carpeting or cover the power cord with rugs, runners or the like. Arrange the power cord away from traffic areas and where it will not be tripped over.
Do not route power cord under furniture or appliances.
Do not operate the air purifier with a damaged power cord or plug, or if the air purifier has been dropped or damaged in any manner. Take the air purifier to your nearest Breville service centre for examination, electrical or mechanical adjustment or repair.
Do not use the air purifier with an external timer, programmer or any other device that switches the air purifier on automatically since a fire risk may exist if the air purifier is covered or positioned incorrectly.
Do not place anything on top of the air purifier when assembled, when in use and when stored.
Never block the air openings, grills/outlets or place on a soft surface such as a bed or sofa, as this could cause the unit to tip over, blocking the air inlet or outlet opening.
Do not attempt to repair or adjust any electrical or mechanical functions on this unit. Doing so will void your warranty. Other than the filter, the inside of the unit contains no user serviceable parts. All servicing should be performed by qualified personnel only.
This air purifier contains a UV-C emitter.
Unintended use of the appliance or damage to the housing may result in the escape of dangerous UV-C light radiation. UV-C light radiation may, even in little doses, cause harm to the eyes and skin.
Keep the air purifier and dust filters clean. Follow the cleaning instructions provided in this book.

IMPORTANT SAFEGUARDS FOR ALL ELECTRICAL APPLIANCES:

Fully unwind the power cord before use.
Connect only to a 230V or 240V power outlet.
Do not let the power cord hang over the edge of a bench or table, touch hot surfaces or become knotted.
To protect against electric shock, do not immerse the power cord, power plug or appliance in water or any other liquid or allow moisture to come in contact with the part, unless it is recommended in the cleaning instructions.
The appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a personresponsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
It is recommended to regularly inspect the appliance. To avoid a hazard, do not use the appliance ifpower cord, power plug or appliance becomes damaged in any way. Return the entire appliance to the nearest authorized Breville Service Centre for examination and/or repair.
Any maintenance other than cleaning should be performed at an authorised Breville Service Centre.
This appliance is for household use only. Do not use this appliance for anything other than its intended use. Do not use in moving vehicles or boats. Do not use outdoors.
Misuse may cause injury.
The installation of a residual current device (safety switch) is recommended to provide additional safety protection when using electrical appliances. It is advisable that a safety switch with a rated residual operating current not exceeding 30mA be installed in the electrical circuit supplying the appliance. See your electrician for professional advice.
During electrical storms, the appliance should be disconnected from the power source at the wall socket to prevent any electrical surges that may arise during the storm and which may inadvertently cause damage to the appliance and its electronic componentry.
Always turn the appliance tothe off position, switch off at the power outlet and unplug at the power outlet when the appliance is not in use.
Before cleaning, always turn the appliance to the off position, switch off at the power outlet, unplug at the power outlet and remove the power cord, if detachable, from the appliance and allow all parts to cool.
Do not place this appliance on or near a heat source, such as hot plate, oven or heaters.
Position the appliance at a minimum distance of 20cm away from walls, curtains and other heat or steam sensitive materials and provide adequate space above and on all sides for air circulation.

Components

A. Air Outlet
B. Control Panel
C. Main Housing Body
D. Air Quality Sensor
E. Air Inlet
F. Microbe ShieldTM Light and Light Guard
G. 3-Layer Filter
H. Base Plate
I. Locking Knob
NOT PICTURED
Power Cord

Control Panel

A. Power On/Off and Filter Reset Button
B. Microbe ShieldTM/Night Mode
C. Timer (up to 8 hours)
D. Fan Speed (includes 4 speed modes; Low, Medium, High and Turbo)
E. Air Quality Sensor Light

The Breville Smart AirTM Purifier has a visible air quality sensor light around the control panel. The light illuminates to indicate the quality of the surrounding air according to the table following:

Grade Air Quality Colour of Light

Very Good Blue
Good Yellow
Fair Orange
Poor Red

Features

YOUR BREVILLE AIR PURIFIER

Your Breville Smart AirTM Purifier improves your indoor air quality using 4 distinct levels of protection.

. A Pre-Filter Captures larger airborne particles such as human hair, pet dander and dust particles.
A True HEPA Filter Traps up to 99.97% of allergens and airborne contaminants down to 0.3 microns in size. These include lung-damaging dust mould spores, plant spores, and pollen.
An Activated Carbon Membrane Along with assisting in the capture of dust, smoke, pollen and other airborne allergens, the activated carbon membrane helps to neutralise odours in the home and to eliminate fumes emitted by household products as well as other volatile organic compounds (VOC’s) that might be found in the air.
Microbe ShieldTM Technology Microbe ShieldTM technology uses a shortwave UV-C light specially designed to target germs and bacteria from the incoming air as it passes through the air purifier before releasing the air back into the surrounding area. The Microbe ShieldTM function can be turned on and off according to preference.

Assembly

BEFORE FIRST USE

Remove and safely discard any packaging material or promotional labels attached to your air purifier and filter.
Remove the filter from the air purifier (see REPLACING THE FILTER on page 11) and take it out of the plastic bag. Then re-insert the filter into the air purifier.
Select a flat and level location for the air purifier.
For proper air flow, locate the unit at least 20cm from any wall or furniture.
Ensure the air inlet and outlets are not blocked before use.
Plug the power plug into a 230V OR 240V power outlet and turn on the power outlet.

IMPORTANT: When moving the air purifier, always lift the unit using two hands and set down gently on a flat and level surface.

Functions

OPERATING YOUR AIR PURIFIER

Press the POWER button to turn on and the On/Filter reset light will illuminate.
The air quality sensor light will illuminate, usually starting with a blue light until it has time to sense the air quality and then it may change to an alternate colour.
To adjust how the air purifier operates, follow the directions below.

NOTE: The filter reset light will blink continuously indicating that the filter needs to be replaced. To reset the indicator after the filter has been replaced, press and hold the POWER button for 5 seconds and the filter reset light will turn off.

SensAirTM LIVE PURITY CONTROL

Your Breville Smart AirTM Purifier has a built-in air quality sensor to detect changes to air quality in the surrounding area.
The SensAirTM light around the control panel will change colours according to the quality of the surrounding air.

Microbe ShieldTM/NIGHT MODE

The Microbe ShieldTM and Night Modes utilise the same button on the control panel. Pressing the Microbe ShieldTM/NIGHT button will cycle through these two settings.

Microbe ShieldTM

Press the Microbe ShieldTM/NIGHT mode button until the Microbe ShieldTM indicator light illuminates to turn it on.
Press again until the light extinguishes to turn off this function.

Night Mode

To turn on Night Mode, press the Microbe ShieldTM/NIGHT button until the night indicator light starts to blink.
After 10 blinks, all indicator lights on the control panel will turn off as the unit enters night mode and the fan speed will automatically change to Low.
Press any button on the control panel to re-engage the control panel and turn off night mode. The indicator light will extinguish.

FAN SPEED/TURBO MODE

Press the FAN SPEED button repeatedly until the desired speed is illuminated on the control panel.
There are 4 fan speeds: Low, Medium, High and Turbo.
The purifier has reached Turbo mode when all three lights are illuminated on the controlpanel at the same time.

TIMER

The air purifier can be set to operate for timed intervals of 2 hours, 4 hours and 8 hours, stopping automatically when the selected operating time has elapsed. If no timer is set, the air purifier will continuously operate until it is manually switched off.
Press the TIMER button repeatedly until the desired interval hours are illuminated on the control panel.
For continuous operation, press the TIMER button repeatedly until there are no lights illuminated under the timer intervals.

AUTO MODE

When in Auto mode, the air purifier will automatically adjust the speed to help filter the air based on the sensor reading.
To set to Auto, press the POWER button continuously until the Auto indicator light illuminates.
Press the POWER button or the Fan Speed button, to turn Auto off and beneath Auto indicator light will extinguish.

FILTER RESET

The On/Filter reset light will blink continuously indicating that the filter needs to be replaced.
Replace the filter according to the directions found under Replacing the Filter in this book.
Once the filter is replaced, press and hold the POWER button for 5 seconds to reset the Filter Reset light.
The built-in timer for the filter reset is 4,320 operating hours.

Care, Cleaning & Storage

The air purifier and filter should be cleaned at least once every month. Ensure the air purifier is switched off and disconnected from the power outlet and allow all parts to cool before cleaning or storing.

Use a clean, dry cloth to clean all external surfaces of the air purifier.
Store the air purifier in an upright position. Do not store anything on top of the air purifier.

BREVILLE RECOMMENDS

Always ensure the air purifier is turned off, switched off at the power outlet and unplugged and allow the unit to cool before performing any cleaning or filter replacement.

DO NOT stick any foreign objects or your fingers inside the air inlet/outlet of this unit.
DO NOT use gasoline, benzine, thinner, harsh cleaners, etc. on and/or in the unit while cleaning as they will damage the unit.
NEVER use alcohol or other solvents on this unit.

CLEANING THE SENSOR

It is important to keep the air quality sensor clean for best performance.
The air quality sensor is situated behind a grill at the rear of the unit.
Gently vacuum the air quality sensor grillusing a small hand brush tool. Cleaning should occur regularly, at least once a month.
If more dust can be seen on the sensor behindthe grill then remove the cover by using the raised tab on the edge of the cover. Push inwards and outwards simultaneously to open the cover, noting that it will be tight.
Gently vacuum the metal shield of the air quality sensor using the hand brush tool.
Replace the cover when clean, ensuring it clicks into place.

FILTER CLEANING AND REPLACING

The Pre-filter should be cleaned at least once every month using a vacuum cleaner. Gently vacuum using a hand-tool attachment such asa brush or upholstery tool. Clean more often if required.
Do not attempt to clean the carbon filter with a vacuum as this can cause damage.
Do not use any solutions, hard bristle brushes or sharp objects to clean as this can cause damage.
Replace the filter as indicated using the instructions following.

REPLACING THE FILTER

Your Smart AirTM Purifier filter should be replaced in the time frames indicated below

The filter life is approximately 6 months if used 24 hours daily, or 12 months if used 12 hours daily.
The filter life may vary to this timing depending on environmental conditions.
Remove all packaging from the replacement filter and place the filter into the unit as described below.

Carefully, turn your air purifier upside down and remove the locking knob from the base of the unit.
Remove the base plate.
Remove the used filter, being careful that any residue or debris that may fall from the filter will not cause damage.
Insert the replacement filter into the unit, ensuring that it is correctly fitted and centred.
Replace the base plate and refasten the locking knob.
Return the air purifier to an upright position.
Turn on the air purifier then press and hold the POWER button for 5 seconds to reset the Filter Reset light.

REPLACEMENT FILTERS

Replacement filters can be purchased from the Breville website^ or at participating retail outlets. See the table below for the replacement product code to suit this Breville AirPurifier.

REPLACEMENT FILTERS

Please contact Breville Customer Service Centre for further support.
Only use the original Breville filter specially intended for this appliance. Do not use any other filters.

Troubleshooting

MINI TROUBLESHOOTING GUIDE

Before carrying out any of the following service checks, unplug the unit from the mains.

Troubleshooting

Breville Customer Service Centre

Australian Customers
Phone: 1300 139 798
Web: www.breville.com
New Zealand Customers
Phone: 0800 273 845
Web: www.breville.com

Breville LAP300 Smart Air Purifier Instruction Manual – Optimized PDF
Breville LAP300 Smart Air Purifier Instruction Manual – Original PDF