BATO BAP-2848R Alcove Bathtub with Apron Installation Guide

BATO BAP-2848R Alcove Bathtub with Apron

Specifications:

• Model: BAP-2848R
• CUPC File No.: 7136
• Certified Model: WTM-02848R
• Weight Capacity: Minimum of 1500 lbs

Product Usage Instructions

Installation:

1. Prepare the area by framing where the tub will be installed.
2. Place the tub in the desired location, ensuring it is level on all sides.
3. Mark the location of the drain and wall studs on the tile flange.
4. Remove the tub and install the drain, predrilling holes on the tile flange at the marked stud locations.
5. Move the tub back into place, ensuring it is level and plumb. Adjust feet or shim as needed.
6. Secure the wall with galvanized screws at predrilled locations, apply weight to the middle of the tub until mortar sets.

Cleaning and Maintenance:

Clean the bathtub with a damp cloth only, avoiding metal or
abrasive polishes. Install water-resistant gypsum board and finish
surface material (e.g., tile, stone), sealing all edges with
silicone caulking to prevent water damage.

FAQ:

What does the warranty cover?
The warranty covers different components for varying durations:

• 1 year for certain parts
• 2 years for other parts
• 10 years for specific components

What are the exclusions from the warranty?
Exclusions from the warranty are not specified in this manual. Please refer to the warranty documentation for detailed information.

BEFORE STARTING

Our products are carefully inspected and packaged in our warehouse for shipping. Only remove the protec-tive film at the very end of the installation to ensure maximum protection. (Except where the bathtub surface will be in permanent contact with another surface (I.E., Wall/faucet, etc)). It is very important that you carefully inspect the product before installation. If a product is defective, please contact the company before installation. The installer will be held responsible for any breakage or damages following the use of a defective product. To protect the unit during installation, place cardboard in the bottom of the bathtub. Verify that the bathroom floor is levelled and strong enough to support a minimum weight of 1500 lbs, and reinforce the existing flooring if needed. It is IMPORTANT to verify the drain location (it can be placed of the left, middle of right) before drilling a hole in the floor. It is important to provide access near the plumbing, pump and/or control boxes allowing to easily disassemble and/or repair these components. The whirlpool/Therapeutic systems must be connected before the final installation. (see the installation and user’s guide for the whirlpool/therapeutic system).

REQUIRED TOOLS

DIMENSION

INSTRUCTIONS ARE TO BE PRESERVED BY FINAL USER. READ CAREFULLY BEFORE PROCEEDING WITH INSTALLATION.

INSTALLATION INSTRUCTIONS

Important point to remember before beginning installation:

• Verify that floor is structurally sound and level, floor must be able to support the full load of the tub including water to the overflow level.
• Provide access to all plumbing connections.
• Observe all local building and plumbing codes.

1. Prepare area by framing the area where the tub will be installed.
2. Place the tub at the location where the tub will be installed, level the tub on all sides and mark the location of the drain and the wall studs on the tile flange.
3. Remove the tub and install the drain, and predrill holes on the tile flange at the marked location of the studs.
4. Apply a thin layer (1″ to 2″) of mortar mix cement to the area where your tub basin will be sitting.
5. Move the tub into place, make sure it is level and plumb adjust feet or shim as necessary.
6. Secure the wall with galvanized screws at the predrilled screw location, and apply weight to the middle of the tub until the mortar sets.
7. Connect the tub drain to your drain system.
8. Install water-resistant gypsum board and finish surface material (tile, stone) and seal all edges with silicone caulking to prevent water damage.

CLEANING

• Clean with a damp cloth only.
• Avoid using metal or abrasive polishes.

Parts list

Required tools:

Installation steps

• Step 1. Place the tub on the packaging upside down and install the metal supports.
• Step 2. Use a level to make sure the apron is vertical and level to the the ground.
• Step 3. Install the metal bars on the wood part of the base using the provided screws and repeat for the 2 remaning bars.
• Step 4. Adjust the 5 feets to level the tub.
  Remarks: The 3 Metal Supports must be fixed with screws to assure that the apron of tub is straight.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>