rock space RSD0613 AC2100 Tri Band Whole Home Mesh WiFi System Installation Guide
- June 5, 2024
- rock space
Table of Contents
Quick Installation Guide
AC2100 Tri-band Whole Home Mesh Wi-Fi System
Model No. RSD0613 (3-pack
In the box
Mesh node x 3
Power adapter x 3| Ethernet cable x 1
Quick Installation Guide x 1
---|---
Get to know your device
Download the RS WiFi app
Download the RS WiFi app to your mobile device from App Store /Google Play, or by scanning the QR code below
Connect the primary node
- The first Mesh box you set up functions as the primary node, while the rest are referred to as the secondary nodes
- Plug one of the nodes (note: this is your primary node) into an outlet using the included power adapter. The LED indicator turns solid green.
- Connect one end of the included Ethernet cable to the LAN port of your modem and the other end to the WAN/LAN port of the primary node. The indicator light will be solid green, indicating the system is ready for setup.
Set up the primary node
-
Open the Wi-Fi menu on your smart device. Select the primary node’s SSID (network name) to connect.
Note: The default SSID and password are labeled at the bottom of the node.|
---|--- -
Go to your mobile and open the RS WiFi app. The setup wizard appears.
Tap Setup. -
The app detects your connection type automatically. If your connection type is dynamic IP, tap Next. If it is PPPoE, enter your PPPoE username and password and tap Next. If it is static IP, enter your IP address and other information your ISP provides, and tap Next.
-
Create your Wi-Fi Name and Password. Tap OK.
Note: Your mobile phone will disconnect from the original mesh Wi-Fi network. Please reconnect to the new wireless network. -
You have set up the primary node successfully.
Connect the secondary nodes
-
Choose a proper place.
− Place it out in the open and don’t put it on the door.
− Keep your nodes away from electronic interference, such as microwaves,
TVs, refrigerators, etc. -
Connect the nodes.
Method 1: Power on the other two nodes, they will automatically be added to the mesh network. The LED indicator will turn solid green. If method 1 fails, try method 2. Method 2: On the RS WiFi app, tap Settings > Add rock space mesh, and scan the QR code on the back of the node to add.
After setup, you can use the LED indicator to determine an ideal location to place your node.
| Solid green| Good connection
---|---|---
| Solid yellow| Fair connection
| Solid red| Disconnected
If the LED Indicator of a node is not solid green, relocate it to get a better
connection.
To access the internet with:
− Wired devices: Connect wired devices to the LAN ports of any node.
− Wireless devices: Connect wireless devices to the Wi-Fi network using the
Wi-Fi name and password you set.
If you want to manage your network, go to the RS WiFi app to control it
anytime and anywhere.
FAQ
Q1: How can I connect my devices, such as a home security camera or
printer, to the 2.4 GHz signal?
Run the RS WiFi app, tap Settings > Smart Assistant > Enable. The mesh system
will switch to the 2.4 GHz band in the following 30 minutes. After half an
hour, the connection would be automatically terminated and switched back to
the 5 GHz band, while your 2.4 GHz devices will still be connected to the 2.4
GHz band.
Note: Make sure your smartphone is connected to the mesh’s network and
check if the app has been updated to the latest version.
Q2: How can I change my network name (SSID) and password?
Run the RS WiFi app, tap Settings > Wireless Settings, change your SSID and
password, and tap Save.
Then, reconnect your devices to the Internet using the new SSID and password.
Q3: How can I remove a node from my mesh Wi-Fi network?
Tap the node on the RS WiFi app, tap “…” in the upper-right corner, and choose
Delete.
Note that removing a node restores it to factory settings.
Q4: Can I add another new set of nodes to expand my network coverage?
Yes. Run the RS WiFi app, tap Settings > Add rock space mesh, and scan the QR
code on the back of the node to add.
Q5: How to restore my device to factory settings?
With the nodes powered on, hold the Rest button of your primary node using a
paper clip for about 6 seconds, and release it when the LED indicator blinks
fast. And all nodes are restored to factory settings.
Q6: How to enable WPS on my rock space device?
Run the RS WiFi app, and tap Settings > WPS. The LED indicator blinks green
slowly. Try to finish your connection within 2 minutes.
Q7: How to set AP mode?
Step 1 : Run the RS WiFi app. Go to Settings > Internet Settings >
Connection Type. Select Bridge and tap Save. Wait a few minutes, the app will
reconnect to the network.
Step 2 : Power on the other two nodes, the LED blinks green. Your network
is established when LED turns to solid green.
If you need further help, please contact us at
techsupport@rockspace.cc for more support.
LED indicator description
After a node is powered on, the LED indicator lights solid green for about 40 seconds to complete startup. Then, the LED indicator lights one of the following colors:
Node Type | Status | Description |
---|
Primary node
| Fast blinking green| Connecting to the Internet
Solid green| Connected to the Internet
Solid red| Disconnected
Secondary node
| Slow blinking green| Connecting to or searching for another node
Fast blinking green| Connecting to the Internet
Solid green| Good connection
Solid yellow| Fair connection
Solid red| Disconnected
For EU/EFTA, this product can be used in the following countries:
BE| BG| CZ| DK| DE| EE| IE
EL| ES| FR| HR| IT| CY| LV
LT| LU| HU| MT| NL| AT| PL
PT| RO| SI| SK| FI| SE| UK
CE Mark Warning
This is a Class B product. In a domestic environment, this product may cause
radio interference, in which case the user may be required to take adequate
measures.
Operations in the 5.15-5.25Gliz band are restricted to indoor use only. This
equipment should be installed and operated with a minimum distance of 20cm
between the radiator & your body.
NOTE:
- The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment.
- To avoid unnecessary radiation interference, it is recommended to use a shielded RJ45 cable.
WARNING: The mains plug is used as a disconnect device, the disconnect
device shall remain readily operable.
Declaration of Conformity for Mesh3 Hereby, SHENZHEN RENQING EXCELLENT
INVESTMENT CO., LTD.declares that the radio equipment type
Mesh3/RSD0613(RSD0613is composed of one to three Mesh3) is in compliance with
Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the
following internet address: http://www.tendacn.com/en/service/download-
cata-101.html
Operate Frequency:
2.4 GHz: EU/2400-2483.5MHz (CH1-CH13)0-5250
5 GHz: EU/515MHz (CH36-CH48)
EIRP Power (Max.):
2.4 GHz: 19.67dBm
5 GHz: 22.21dBm
Software Version: V1.0.0.32
FCC Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device is restricted to being used indoors. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Radiation Exposure Statement
This device complies with FCC radiation exposure limits set forth for an
uncontrolled environment and it also complies with Part 15 of the FCC RF
Rules.
This equipment should be installed and operated with a minimum distance of
20cm between the radiator & your body.
Caution:
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
NOTE:
- The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment.
- To avoid unnecessary radiation interference, it is recommended to use a shielded RJ45 cable.
Caution:
Adapter Model: BN071-Al2012E/BNO36-Al2012B/BN071-Al2012U
Manufacturer: SHENZHEN RENQING EXCELLENT INVESTMENT CO., LTD.
Input:100-240 V AC, 50/60 Hz, 0.6 A
Output:12 V DC,1.5A : DC Voltage
Operating Environment
Temperature: 0°C-40°C Humidity: (10 – 90)% RH, non-condensing
RECYCLING
This product bears the selective sorting symbol for waste electrical and
electronic equipment (WEEE).
This means that this product must be handled pursuant to European directive
2012/19/EU in order to be recycled or dismantled to minimize its impact on the
environment. The user has the choice to give his product to a competent
recycling organization or to the retailer when he buys new electrical or
electronic equipment.
Technical Support
Shenzhen Renqing Excellent Technology Co., Ltd. Address. 104, No.15, Longfu
Industrial Zone, Huarong Road, Tongsheng Community, Dalang Street, Longhua
District, Shenzhen, China Email:
techsupport@rockspace.cc Website:
www.rockspace.cc Technical Phone Support:
+1(833)816-6558 Service Time: EST: 9:00-17:00 / PDT: 06:00-14:00,from Monday
to Friday 24hour Online After-sales Service:
https://rockspace.afterservice.vip
*NOTE: Please go to the rock space official website to download specific
using instructions. www.rockspacewifi.com
Copyright
© 2019 Shenzhen Renqing Excellent Technology Co., Ltd. All rights reserved.
rock space is a registered trademark legally held by Shenzhen Renqing
Excellent Investment Co., Ltd. Other brand and product names mentioned herein
are trademarks or registered trademarks of their respective holders.
Specifications are subject to change without notice.
24hour Online
After-sales Service
Scan QR Code To Visit
https://rockspaceworld.com
Email: techsupport@rockspace.cc
Tel: +1 833-816-6558
Service Time:
EST 10:00 – 21:00 from Monday to Friday
References
- rockspace Official: re.rockspace.local Extender Setup
- rock space Official | Cutting Machine | Plotter | Film Cutting Machine | Screen Protector Cutter | On-demand Cut | Custom
- rockspace Official: re.rockspace.local Extender Setup
- rockspace Official: re.rockspace.local Extender Setup
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>