Helmholz 700-842-5ES01 FLEXtra SLIM Ethernet-Switch Unmanaged Owner’s Manual
- June 1, 2024
- Helmholz
Table of Contents
Helmholz 700-842-5ES01 FLEXtra SLIM Ethernet-Switch Unmanaged
Specifications
- Order No.: 700-842-5ES01
- Name: FLEXtra SLIM Ethernet-Switch 5-Port, unmanaged, 100 Mbps
- Scope of Delivery: Ethernet 5-port switch with power supply plug, short manual
- Dimensions (DxWxH): 35.1 mm x 25 mm x 109 mm (without connector)
- Weight: Approx. 115g
- LAN Interface (X1): 5 RJ45 ports
- Connection: 10/100 Mbps
- Transmission Rate: 10/100Base-T/TX, Full/Half-Duplex, Auto-negotiation, Auto MDI/MDI-X; IEEE Auto crossover; LLDP & PTCP Delay-Traffic blocking (for PROFINET networks)
- Status Indicator: 1 LED, green; 10 LEDs, orange/green
- Power Supply: 24 V DC (18-30 V DC)
- Current Draw: Max. 55 mA at 24 V DC
- Power Loss: Max. 1.4 W
Product Usage Instructions
Installation
- Mount the FLEXtra SLIM Ethernet-Switch on a DIN rail in a suitable location.
- Connect up to 5 Ethernet participants using RJ45 cables to the available ports.
- Ensure correct power supply connection with a voltage between 18-30 V DC.
LED Indicators
The LED indicators provide visual feedback on the status of the switch:
- PWR Led: On = Power supply present, Off = Novoltage or the device is defective
- RJ45 LEDs: Orange (Link/Activity) and Green(Speed) indicate connection status and speed.
Network Configuration
The switch supports PROFINET networks and complies with PROFINET
Conformance Class A. Ensure proper configuration for your network
requirements.
Maintenance
Regularly check for firmware updates and refer to the latest documentation available on the manufacturer’s website for troubleshooting and support.
Application area
The Helmholz „FLEXtra SLIM Ethernet-Switch 5-Port, unmanaged, 100 Mbps“ is
suitable for installation on a DIN rail and connects up to 5 Ethernet
participants with 10 or 100 Mbps. The FLEXtra SLIM Ethernet-Switch is suitable
for PROFINET networks. The LLPD (neighborhood detection) and PTCP (time
synchronization) functions are handled correctly with the switch by the
PROFINET standard. The FLEXtra SLIM Ethernet Switch thus complies with
PROFINET Conformance Class A.
Connections
The FLEXtra SLIM Ethernet-Switch has 5 RJ45 connectors (X1 P1 – X1 P5). The
switch must be supplied with 24 V DC at the wide range input “Ext. V DC 18…30
V” via the supplied connector plug.
The connection (FE, ) is for the functional earth. Connect this properly to
the reference potential.
Features
- Store-and-Forward architecture
- 10Base-T/100Base-TX
- Full-/Half-Duplex
- Autonegotiation
- Auto MDI/MDI-X (IEEE 802.3u Auto crossover support)
- LLDP & PTCP Delay-Traffic blocking (for PROFINET networks)
- PROFINET Conformance Class A
- QoS-Priority Queues: 2 per port
- 1K MAC address lookup table
- 448K bits packet buffer memory
- Max. forwarding packet length 1552 bytes
LEDs
PWR Led
- On = Power supply present
- Off = No voltage or the device is defective
RJ45 LEDs
- Orange (Link/Activity): On = Connected/Blinks = Data transmission
- Green (Speed): On = 100 Mbps/Off = 10 Mbps
Attention: If the device is used in a manner not specified by the manufacturer, the protection provided by the device may be affected. Pay special attention to the correct contact during cable installation. If you have problems, always read the latest documentation first, which can be found on the Internet at www.helmholz.com. Connected circuits shall meet the requirements of Limited energy circuits acc. UL61010-1.
Technical data
| Order no. | 700-842-5ES01 |
|---|---|
| Name | FLEXtra SLIM Ethernet-Switch 5-Port, unmanaged, 100 Mbps |
| Scope of delivery | Ethernet 5-port switch with power supply plug, short manual |
| Dimensions (DxWxH) | 35,1 mm x 25 mm x 109 mm (without connector) |
| Weight | approx. 115g |
| LAN interface (X1) | |
| Number | 5 |
| Connection | RJ45 |
| Transmission rate | 10/100 Mbps |
Type
| 10/100Base-T/TX, Full/Half-Duplex, Autonegotiation, Auto MDI/MDI-X; IEEE Auto crossover;
LLDP & PTCP Delay-Traffic blocking (for PROFINET networks)
Status indicator|
Power display| 1 LED, green
Ethernet status| 10 LEDs, orange/green
Power supply|
Voltage supply| 24 V DC (18…30 V DC)
Current draw| max. 55 mA at 24 V DC
Power loss| max. 1,4 W
Ambient conditions|
Ambient temperature| -25 °C … +60 °C
Transport and storage temp.| -40 °C … +85 °C
Relative air humidity| 95% r H without condensation
Pollution degree| 2
Protection rating| IP20
Approvals| CE
Note: The contents of this document have been checked by us for matching with the hardware and software described. However, we assume no liability for any existing differences, as these cannot be fully ruled out. The information in this document is, however, updated on a regular basis. When using your purchased products, please make sure to use the latest version of the document, which can be viewed and downloaded on the Internet at www.helmholz.de.
MORE INFORMATION
Helmholz GmbH & Co. KG | Hannberger Weg 2
- 91091 Großenseebach
- Phone +49 9135 7380-0
- Fax + 49 9135 7380-490
- info@helmholz.de
- www.helmholz.de
FAQ
- Q: What should I do if I encounter connection issues with the switch?
- A: Check the cable connections, power supply, and network configuration. Ensure all devices are compatible with the switch.
- Q: Can I use the FLEXtra SLIM Ethernet-Switch in environments with varying temperatures?
- A: The switch is designed to operate within specified ambient temperature ranges. Avoid extreme temperature conditions for optimal performance.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>