PORTOR LIGHTING PT-DLSB2-R SERIES Slim 6 Inch LED Recessed Downlight Instruction Manual

Table of Contents

PORTOR-LIGHTING-PT-DLSB2-R-SERIES-Slim-6-Inch-LED-Recessed-Downlight-
PRODUCT

Specifications

Model: PT-DLSB2-R SERIES
Variants: PT-DLSB2-R-6I-12W-5CCT / PT-DLSB2-R-4I-9W-5CCT
Installation: Indoor Only
Power Supply: Consult a qualified electrician
Hole Cut Size:
- 4 round and square: 4.3″ (110 mm)
- 6 round and square: 6.3″ (160 mm)

Disconnect electrical power before starting installation.
Locate a suitable position for the fixture and open it according to the cut-hole dimensions.
Run electrical wire from the switch through the mounting hole using NMD90 Romex or BX cable.
Open the hardwire box swing cover and remove the appropriate knockout(s).
Insert the electrical supply cable through the knockout and secure it with a cable connector.
Connect ground, white, and black wires according to instructions.
Place all wiring back into the box and close the cover.
Insert the hardwire box through the mounting hole.
Connect the fixture to the hardwire box using male/female connectors.
Select the desired Color Temperature.
Insert the fixture base into the mounting hole and secure it in place.
Turn on the power to confirm the fixture is working properly.

Q: Can this fixture be used for outdoor installations?
A: No, this fixture is designed for indoor use only.
Q: What type of electrical wire should be used for connecting the fixtures?
A: Use NMD90 Romex or BX cable suitable for the application to connect the fixtures.

IMPORTANT

SAFETY

FOR YOUR SAFETY, THIS FIXTURE MUST BE WIRED UNDER LOCAL ELECTRICAL CODES AND ORDINANCES. ALL WORK SHOULD BE DONE BY A QUALIFIED ELECTRICIAN.

WARNING

MAKE CERTAIN POWER IS OFF FROM THE ELECTRICAL PANEL BEFORE STARTING INSTALLATION OR ATTEMPTING ANY MAINTENANCE. INDOOR INSTALLATION ONLY.

PREPARING FOR INSTALLATION: DISCONNECT ELECTRICAL POWER BEFORE INSTALLING OR SERVICING ANY PART OF THIS FIXTURE.
LOCATE A SUITABLE POSITION TO PLATE THE FIXTURE AND OPEN IT UNDER THE CUT-HOLE DIMENSIONS (REFER TO HOLE CUT TABLE FOR APPROPRIATE SIZE).
RUN ELECTRICAL WIRE FROM THE SWITCH (POWER SUPPLY) THROUGH THE MOUNTING HOLE-USE NMD90 ROMEX OR BX CABLE.

PORTOR-LIGHTING-PT-DLSB2-R-SERIES-Slim-6-Inch-LED-Recessed-Downlight-
FIG-1

PORTOR-LIGHTING-PT-DLSB2-R-SERIES-Slim-6-Inch-LED-Recessed-Downlight-
FIG-2

DRIVER WIRING

Open the hardwire box swing cover and remove the appropriate knockout (s).
Insert the electrical supply cable through the knockout and secure it with a cable connector (sold separately).
Using wire nuts, connect the green ground wire of the cable to the green wire on box. Connect white wire of the cable to the white wire of the box. Connect the black wire of the cable to the black wire of the box. (Figure 1)
Place all wiring and connections back into the box and close the cover.
Insert the hardwire box through the mounting hole. (Figure 2) NEW CONSTRUCTION APPLICATIONS: Hardwire box shall be firmly secured to studs, joists, or similar fixed structural units.
REMODEL APPLICATIONS: Do not require the hardwire box to be firmly secured after the mounting plates, studs, joists, or structural units have been concealed.

FIXTURE INSTALLATION

Connect the fixture to the hardwire box by inserting and twisting the male/female connectors. Select the desired Color Temperature. (Figure 3)
Push spring-loaded clips on the fixture upwards and insert the fixture base into the mounting hole. Release the clips and the fixture will be pulled flush to the ceiling. (Figure 4)
Once assembly is complete, turn on the power to confirm the fixture is working properly.

HOLE CUT SIZE