Arktic 226568 233900 233917 233924 233931 235829 235836 BACK BAR REFRIGERATOR User Manual
- June 7, 2024
- Arktic
Table of Contents
User manual
Item: 226568,233900,233917,233924,233931,235829
235836 BACK BAR REFRIGERATOR
You should read this user manual carefully before using the appliance.
Keep these instructions with the appliance.
For indoor use only.
Dear Customer,
Thank you for purchasing this Arktic appliance. Before using the appliance for
the first time, please read this manual carefully, paying particular attention
to the safety egulations outlined below.
Safety regulations
- This appliance is intended for commercial use only.
- The appliance must only be used for the purpose for which it was intended and designed. The manufacturer is not liable for any damage caused by incorrect operation and improper use.
- Keep the appliance and electrical plug away from water and any other liquids. In the event that the appliance should fall into the water, immediately remove the plug from the socket and do not use it until the appliance has been checked by a certified technician. Failure to follow these instructions could cause a risk to lives.
- Never attempt to open the casing of the appliance yourself.
- Do not insert any objects in the casing of the appliance.
- Do not touch the plug with wet or damp hands.
- The danger of electric shock! Do not attempt to repair the appliance yourself. In case of malfunctions, repairs are to be conducted by qualified personnel only.
- Never use a damaged appliance! Disconnect the appliance from the electrical outlet and contact the retailer if it is damaged.
- Warning! Do not immerse the electrical parts of the appliance in water or other liquids. Never hold the appliance under running water.
- Regularly check the power plug and cord for any damage. If the power plug or power cord is damaged, it must be replaced by a service agent or similarly qualified persons in order to avoid danger or injury.
- Make sure the cord does not come in contact with sharp or hot objects and keep it away from an open fire. To pull the plug out of the socket, always pull on the plug and not on the cord.
- Ensure that the cord (or extension cord) is positioned so that it will not cause a trip hazard.
- Always keep an eye on the appliance when in use.
- Warning! As long as the plug is in the socket the appliance is connected to the power source.
- Turn off the appliance before pulling the plug out of the socket.
- Never carry the appliance by the cord.
- Do not use any extra devices that are not supplied along with the appliance.
- Only connect the appliance to an electrical outlet with the voltage and frequency mentioned on the appliance label.
- Connect the power plug to an easily accessible electrical outlet so that in case of emergency the appliance can be unplugged immediately. To completely switch off the appliance pull the power plug out of the electrical outlet.
- Always turn the appliance off before disconnecting the plug.
- Never use accessories other than those recommended by the manufacturer. Failure to do so could pose a safety risk to the user and could damage the appliance. Only use original parts and accessories.
- This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge.
- This appliance must not be used by children under any circumstances.
- Keep the appliance and its cord out of reach of children.
- Always disconnect the appliance from the mains if it is left unattended or is not in use, and before assembly, disassembly or cleaning.
- Never leave the appliance unattended during use.
Special Safety Regulations
-
This appliance is not intended to cool down the beverages or to store them for a long period of time. They should be cooled down first (< 6 °C) before placing in the appliance.
-
All technical activities like installation, maintenance, or repair work must be performed by qualified service personnel only.
-
WARNING: Do not use mechanical devices or other means to accelerate the defrosting process, other than those recommended by the manufacturer.
-
WARNING: Do not damage the refrigerant circuit.
-
Caution! Risk of fire! The refrigerant used is R600a in this appliance. It is a flammable refrigerant that is environmentally friendly. Although it is flammable, it does not damage the ozone layer and does not increase the greenhouse effect. The use of this coolant has, however, led to a slight increase in the noise level of the appliance. In addition to the noise of the compressor, you might be able to hear the coolant flowing around the system. This is unavoidable and does not have any adverse effect on the performance f the appliance. Care must be taken during the transportation and setting up of the appliance that no parts of the cooling system are damaged. Leaking coolant can damage the eyes.
-
The foam blowing agent used is C5H10 in this appliance. It is highly flammable.
-
WARNING: Keep all ventilation openings in the appliance enclosure clear of obstruction.
Provide sufficient ventilation in the surrounding structure when building in. Never block
the airflow suction and air outlet in order to keep air circulation. -
WARNING: Do not use electrical appliances inside the food storage compartments of the
appliance, unless they are of the type recommended by the manufacturer. -
Place the appliance on a clean, stable, dry, level surface only.
-
Keep the appliance away from any hot surfaces and open flames. Protect the appliance
against heat, dust, direct sunlight, moisture, dripping, and splashing water. -
During use, keep 10cm around the appliance free for ventilation.
-
Do not use hard utensils on the glass surface. Do not use water jets or steam cleaners
during cleaning, do not immerse the whole appliance in water as the parts will get wet
and electric shock might result. -
Do not place articles on top of the appliance. Do not place objects with open sources of fire (e.g. candles) on top or beside the appliance. Do not place objects filled with water (e.g. vases) on or near the appliance.
-
Never cover the appliance during use. This may cause a fire hazard.
-
Do not wash the appliance with water. Washing can cause leakages and increase the risk of electric shock.
-
Do not make any additional openings on the appliance. Do not install any gadgets in the appliance.
-
Do not overload the racks inside to avoid damage. Max. loading of each rack is about 8kg.
-
Do not attempt to climb up to the top of the appliance.
-
CAUTION! Handle the glass surfaces with care; protect them from impacts to avoid damage to property and personal injury.
Installing the appliance
- The appliance should not be tipped over an angle of 45°. After installing the appliance, wait for 2 hours before connecting it to the electrical power supply to switch on. The same applies if the appliance is moved at a later date.
- The appliance must always be installed in a dry environment.
- When installing, leave at least 10 cm clearance to the rear and to the left and right for adequate ventilation. Leaving less room for ventilation may affect efficiency.
- We strongly recommend installing the appliance in a place with good natural ventilation to increase ventilation properties.
Electrical components and other dangers
- No other appliances should be plugged into the same socket as with this appliance.
- Do not place any dangerous products, such as fuel, alcohol, paint, flammable or explosives, etc. inside or near the appliance as it may result in a fire hazard.
- Do not store any medications in the appliance.
- Wait about 5 minutes before switching on the appliance again after the appliance has been switched off or unplugged from the electrical power supply.
- Do not wash the appliance with water. Washing can cause leakage and increase the risk of electric shock. No parts/accessories can be under the dishwasher.
Intended use
- This appliance is intended for professional use.
- This appliance is designed only to keep beer, including beverages, under a cool state and to display them for retail sale in restaurants, canteens, other commercial enterprises such s bakeries, butcheries, supermarkets, etc. Any other use may lead to damage to the appliance or personal injury.
- Operating the appliance for any other purpose shall be deemed a misuse of the device. The user shall be solely liable for improper use of the device.
Grounding installation
This appliance is classified as a protection class I appliance and must be
connected to protective ground. Grounding reduces the risk of electric shock
by providing an escape ire or the electric current. This appliance is equipped
with a cord having a grounding wire with a grounding plug. The plug must be
plugged into an outlet that is properly installed and grounded.
Main parts of the appliance
-
Digital control panel
a. Set button for setting temperature
b. Light ON/ OFF/ Increase setting of temperature
c. Decrease setting of temperature
d. Confirm setting/manual defrost
e. Temperature digits -
Air vents
-
Shelf
-
Glassdoor handle
-
Light
-
Door key lock
Remark: The content of this manual applies to all listed items unless specified otherwise. The outlook and appearance may vary from the shown illustrations.
Indicator light status description
Symbol indicator | Status | Description |
---|
set
| ON| Under setting mode
OFF| Operating under the setting condition
out
| ON| The compressor works and cooling active
OFF| Compressor not works and cooling inactive
FLASH| Preparing cooling process
C| ON| Under refrigeration process
def| ON| Under defrost process
Set the temperature
-
Plug into a suitable electrical outlet.
-
When the set indicator light is OFF, press and hold 1a. button for 3 to 4 seconds until is shown on the display. Then, release the 1a. button & press
-
Next, press 1b. button to increase the set temperature by 1°C or press 1c. button to decrease by 1°C.
-
After that, press 1d. button to confirm the setting and exit.
Note: -
If no button is pressed within 30 seconds, the newly set temperature will be stored automatically.
Switch the light ON/OFF -
Press 1b. button to switch ON the light.
-
Press 1b. button again to switch OFF the light.
Loading the appliance -
Always let the appliance reach the set temperature before placing or beverages inside the appliance. Check the cooling temperature display and additionally put a hand into the compartment to feel the actual temperature.
-
Always cool down the beverages to their intended temperature (< 6 °C) before storing in the appliance.
Defrost -
The appliance will start to defrost process automatically every 6 hours.
Shelf height adjustment -
The height of each shelf can be adjusted.
-
The temperature setting ranges from 2°C to 10°C.
-
Distribute the food evenly with sufficient surrounding spacings go ensure proper air circulation.
-
Do not exceed the maximum shelf load stated in the technical specification.
-
Ensure the doors are always properly shut and reduced the times of opening doors to a minimum.
-
When the def indicator is ON, the appliance is under defrost process.
-
Adjust the height of each shelf according to the height of the items.
Installation instructions
- Remove the appliance from the carton box, then remove the external and internal packaging and wrapping.
- Check to make sure the appliance is undamaged. In case of incomplete delivery and damages, DO NOT use the appliance. Please contact supplier (See ==> Warranty).
- Let the appliance stand upright for about 2 hours. This is to reduce the malfunction of the cooling system from improper handling during transportation.
- Clean interior surface with warm water and a soft cloth. (See ==> Cleaning and Maintenance).
- Place the appliance on a horizontal, stable, and heat-resistant surface that is safe against water splashes.
- The optimum working ambient temperature is between 16°C and 30°C. Otherwise, the functionality will be limited.
- Ensure that there is sufficient ventilation. Keep a minimum distance of 10 cm around the appliance. Do not block the ventilation holes.
- For energy savings, always make sure the door is closed.
Operation
Placement
- Place the appliance on a stable and level surface/ floor.
- Ensure the appliance is properly leveled using a water spirit level (not supplied). Use furniture leveling wedges, if you detect the appliance is not leveled or wobbling. Switching the appliance ON/OFF
- The appliance is switched ON once it is connected to the suitable electrical power supply. Simply unplug to switch OFF the appliance.
- A sound will be heard when connected to the power supply.
- Let the appliance rest in its intended position for about 2 hours before operating to prevent damages to the cooling circuit through shaken refrigerant.
- Wait at least 5 minutes before plugin again after unplugging the appliance or power sudden break.
- Unplug the appliance when not in use.
Cleaning and Maintenance
Attention: Always unplug the appliance from the electrical power outlet
before cleaning & maintenance.
Cleaning
- The exterior and interior surfaces can be cleaned with a damp cloth and a little detergent.
- Racks can be removed and washed in water.
- Do not use a water jet or steam cleaner for cleaning and do not push the appliance under the water.
- No parts can be cleaned in the dishwasher.
- Clean the appliance regularly.
Parts | How to clean | Remark |
---|
All accessories such as
racks, rack holders, etc.
| • Soak in warm, soapy water for about 10 to 20 minutes.
• Rinse under running water thoroughly.|
Dry all parts well at last.
External glass surfaces| • Wipe clean with a soft cloth and a little neutral
detergent. Make sure no water or moisture enters the inside of the appliance.
Interior glass surfaces| • Remove any food deposits.
• Wipe clean with a soft cloth and a little mild detergent. Make sure no water
or moisture enters the inside of the appliance.
Glassdoor
|
Putting the appliance out of reach for a long period of time
- Attention: Always unplug the appliance from the electrical power outlet.
- Remove all the food and beverage inside the appliance.
- Clean the appliance as described in Cleaning. (See ==> Cleaning).
- Store the appliance in a cool, clean place and keep it out of reach of the children.
- Clean the appliance as described in Cleaning. (See ==> Cleaning).
- Store the appliance in a cool, clean place and keep it out of reach of the children.
Troubleshooting
If the appliance does not function properly, please check the below table for the solution. If you are still unable to solve the problem, please contact the supplier/service provider.
Problems | Possible cause | Possible solution |
---|
The appliance does not start cooling after connect to the electrical power
supply.| Thermal cut-out activated| Contact the supplier/service provider for
repair.
The compressor is defective.
The power plug is connected correctly with the power supply outlet.| Check the
connection and make sure all the connections are correctly connected.
Cooling is not enough.| The appliance is under strong sunlight radiation or
close to a heat source.| Move the appliance to a new location to avoid direct
sunlight.
The doors are not properly closed or the sealing gasket is defective.| Close
the doors properly.
Too much food is placed inside the appliance.| Placeless food inside the
appliance.
Surrounding ventilation is insufficient.| Check that if sufficient ventilation
is provided by allowing at least 10cm away from other objects or walls.
Too much noise| The appliance is not placed horizon-tally.| Check to make sure
the appliance is placed horizontally.
The appliance touches the surrounding wall or other objects.| Check to make
sure that at least 10cm away from other objects or walls.
There are some loose parts inside the appliance.| Contact the supplier/service
provider for repair.
Technical specification
Item no. | 226568 | 233900 | 233917 | I 233924 | 233931 | 235829 | 235836 |
---|---|---|---|---|---|---|---|
Operating voltage and frequency |
220-240W 50Hz
Rated input power| 135W| 150W| 220W| 240W| 300W| 215W| 300W
Rated current| 1,1 A| 1,0 A| 1,5 A| 1,7 A| 2,3 A| 1.3A| 1.7A
Setting temperature range|
2°C to 10°C
Protection class|
Class I
Noise level|
< 70 dB (A)
The refrigerant used and injection quantity| R600a / 35g| R600a / 35g| R600a /
45g| R600a 160g| R600a / 85g| R600a / 50g| 9600a 190
The flammable foam blowing agent|
C5Hio
Power of the light| 3W| 4W| I 24W| | 9W
Climate class|
N-ST
Inside cabinet capacity| 138L| 118L| 228L| 293L| 458L| 228L| 338L
Number of Shelves| 3| 2| 4| 5| 10| 4| 6
Outer dimension| 600x530x
(H)900mm| 500x500x
(H)900mm| 900x500x
(H1900mm| 600x515x
IH11820mm| 900x515x
(H11820mm| 900x500x
1H1900mm| 1335x500x
(I-11900mm
Remark: Technical specification is subjected to change without prior notification.
Circuit diagram (226568)
Circuit diagram (233900)
Circuit diagram (233917)
Circuit diagram (233924)
Circuit diagram (233931)
Circuit diagram
(235829)
Circuit diagram (235836)
Warranty
Any defect affecting the functionality of the appliance which becomes apparent
within one year after purchase will be repaired by free repair or replacement
provided the appliance has been used and maintained in accordance with the
instructions and has not been abused or misused in any way. Your statutory
rights are not affected. If the appliance is claimed under warranty, a state
where and when it was purchased and include proof of purchase (e.g. receipt).
In line with our policy of continuous product development, we reserve the
right to change the product, packaging, and documentation specifications
without notice.
Discarding & Environment
When decommissioning the appliance, the product must not be disposed of with
other household waste. Instead, it is your responsibility to dispose of your
waste equipment by handing it over to a designated collection point. Failure
to follow this rule may be penalized in accordance with applicable regulations
on waste disposal. The separate collection and recycling of your waste
equipment at the time of disposal will help conserve natural resources and
ensure that it is recycled in a manner that protects human health and the
environment. For more information about where you can drop off your waste for
recycling, please contact your local waste collection company. The
manufacturers and importers do not take responsibility for recycling,
treatment, and ecological disposal, either directly or through a public
system.
Hendi B.V.
Steenoven 21
3911 TX Rhenen, The Netherlands
Tel: +31 (0)317 681 040
Email:info@hendi.eu
Hendi Food Service Equipment GmbH
Gewerbegebiet Ehring 15
5112 Lamprechtshausen, Austria
Tel: +43 (0) 6274 200 10 0
Email: office.austria@hendi.eu
– Changes, printing and typesetting errors reserved.
© 2020 Hendi BV Rhenen – The Netherlands
Ver: 23-04-2020