PORTOR LIGHTING PT-CBL3 Series LED Corn Bulb Instruction Manual
- May 15, 2024
- PORTOR LIGHTING
Table of Contents
PORTOR LIGHTING PT-CBL3 Series LED Corn Bulb
Specifications
- Product Name: PT-CBL3 Series LED Corn Bulb
- Manufacturer: Portor Lighting
- Warning: Do not use an electric generator to test the LED lamp Avoid using the LED fixture in environments with smoke, sulfur, or corrosive substances.
- Material: Glass or semi-glass, semi-metallic
- Power Supply: Main circuit breaker
Product Usage Instructions
Installation
- Turn off the power switch from the main circuit breaker.
- Unscrew the CFL, MHL, or HPS bulb (refer to Figures 3 and 4).
- Remove the existing bulb and screw in the LED corn light (refer to Figures 1 and 2). Ensure that the AC internal driver is properly installed. Note: Remove the ballast before installing the LED corn light to prevent voltage resonance.
- If a security rope is provided, secure one end to the lamp and the other to the shell.
- Turn on the power switch.
FAQ
Q: Can I use the LED corn bulb in environments with smoke or sulfur?
- A: It is recommended to avoid using the LED fixture in environments with smoke, sulfur, or corrosive substances. If necessary, ensure the fixture is well-protected by an enclosed lampshade made of glass or semi-glass, semi-metallic material.
Q: Why must I remove the ballast before installing the LED corn light?
- A: Removing the ballast is essential to prevent voltage resonance that can lead to the breakdown of the LED corn light. Make sure to follow the installation instructions carefully.
CAN NOT USE THE ELECTRIC GENERATOR TO TEST THE LED LAMP. PLEASE AVOID USING THE LED FIXTURE IN ENVIRONMENT WHERE THERE ARE SMOKE, SULFUR, AND CORROSIVE SUBSTANCES. BUT IF USED IN SUCH AN ENVIRONMENT, MAKE SURE THE LED FIXTURE IS WELL PROTECTED BY AN ENCLOSED LAMPSHADE WHOSE DIMENSION IS NO LESS THAN BELOW SIZE, AND WHOSE MATERIAL IS EITHER GLASS OR SEMI-GLASS, SEMI-METALLIC. SURFACE OF THE LAMPSHADE SHALL NOT HAVE ANY COVERING THAT PREVENTS HEAT DISSIPATION.
WARNING
- TO REDUCE THE RISK OF DEATH, PERSONAL INJURY OR PROPERTY DAMAGE FROM FIRE, ELECTRIC SHOCK, FALLING PARTS, CUTS/ABRASIONS, AND OTHER HAZARDS READ ALL WARNINGS AND INSTRUCTIONS INCLUDED WITH AND ON THE FIXTURE BOX AND ALL FIXTURE LABELS.
- BEFORE INSTALLING, SERVICING, OR PERFORMING ROUTINE MAINTENANCE ON THIS EQUIPMENT, FOLLOW THESE GENERAL PRECAUTIONS.
- COMMERCIAL INSTALLATION, SERVICE AND MAINTENANCE OF LUMINAIRES SHOULD BE PERFORMED BY A QUALIFIED LICENSED ELECTRICIAN.
- FOR THE INSTALLATION: IF YOU ARE UNSURE ABOUT THE INSTALLATION OR MAINTENANCE OF THE LUMINAIRES, CONSULT A QUALIFIED LICENSED ELECTRICIAN AND CHECK YOUR LOCAL ELECTRICAL CODE.
- TO PREVENT WIRING DAMAGE OR ABRASION, DO NOT EXPOSE WIRING TO THE EDGES OF SHEET METAL OR OTHER SHARP OBJECTS.
- DO NOT MAKE OR ALTER ANY OPEN HOLES IN AN ENCLOSURE OF WIRING OR ELECTRICAL COMPONENTS DURING KIT INSTALLATION.
WARNING
- ADDED WEIGHT OF THE DEVICE MAY CAUSE INSTABILITY OF A FREE-STANDING
- PORTABLE LUMINAIRE
- USE ONLY WITH A PORTABLE LUMINAIRE THAT IS PROVIDED WITH A SHADE
- SUITABLE FOR USE IN ENCLOSED LUMINAIRES
- NOT FOR EMERGENCY LIGHTING.
INSTALLATION
(ALWAYS TURN OFF THE POWER SUPPLY FROM THE MAIN CIRCUIT BREAKER FIRST!)
- Turn off the power switch.
- Screw off the CFL or MHL or HPS and so on, see Figure (3) (4).
- Take out the led corn light and screw it on, see Figure ( 1) (2).
- Figure ( 1) (2): AC internal driver,
- Note: Make sure to take off the ballast before installing the LED corn light, otherwise the ballast will produce the resonance of high voltage and make the LED corn light break down.
- lf security rope provided, fix the rope on the lamp with hand, then fix the wire of the other end on the shell.
- Turn on the power switch.
Documents / Resources
|
PORTOR LIGHTING PT-CBL3 Series LED Corn
Bulb
[pdf] Instruction Manual
PT-CBL3 Series, PT-CBL3 Series LED Corn Bulb, LED Corn Bulb, Corn Bulb, Bulb
---|---