D-Link DKVM-IP16 16-Port KVM Over IP Switch with VGA and USB Ports Installation Guide
- June 12, 2024
- D-Link
Table of Contents
D-Link DKVM-IP16 16-Port KVM Over IP Switch with VGA and USB Ports
Installation Guide
Package Contents
16-PORT KVM OVER IP SWITCH
DKVM-IP16
KVM CABLE WITH VGA AND USB (x4)
CONNECT THE DKVM-IP16 TO YOUR COMPUTERS
POWER ADAPTER
RACKMOUNT BRACKET (x2)
CD
QUICK INSTALLATION GUIDE
If any of these items are missing from your packaging, please contact your reseller.
Installing the DKVM-IP16
The DKVM-IP16 supports hot-plugging. You don’t need to turn your computers off before installing the device
A. Attach your USB keyboard connector to the console USB port of the
DKVM-IP16.
B. Attach your USB mouse connector to the console USB port of the DKVM-
IP16.
C. Attach your monitor’s HDB 15 VGA connector to the console port of the
DKVM-IP16.
D. Attach the KVM cable (VGA connector) to the VGA port located on the
DKVM-IP16. The following steps below apply to each computer that you are using
with your DKVM-IP16.
E. Attach the KVM cable (USB connector) to the USB port located on the
back of your computer case.
F. Attach the KVM cable (VGA connector) to the VGA port located on the
back of your computer case.
Installation of the DKVM-IP16 is now complete.
Switching with the DKVM-IP16
The DKVM-IP16 features the buttons located on the front panel to switch
quickly and easily between
your computers
Note: Don’t switch PC without finishing PC boot-up.
Hot Keys
You can also use keyboard to switch between your computers. Press the Home / Caps Lock / Scroll Lock / Num Lock key twice within 2 seconds to enter Hot Key switching mode A beep confirms that the Hot Key mode is activated. By default, the Home key is used to enter the Hot Key mode. Alternatively, you can use the Caps Lock, Scroll Lock or Num Lock keys.
Press Home + Home.Enter Hot Key mode by default
…then press Caps Lock Enter Caps Lock Hot Key mode
then press Scroll Lock Enter Scroll Lock Hot Key mode
then press Num Lock
then press / /.Switch to PC1 / PC2 / ..
then press or Switch to next PC
then press or Switch to previous PC
then press Toggle the audible beep confirmations on and off
Then press Start autoscan mode, which will switch to the next PC automatically after scan interval expires (5 seconds by default). Press any key to stop autoscan mode
Note: Hot Keys can be achieved under OSD mode. Press Home + Home + Enter to enter OSD menu.
Note: If you are using OSD, you can click directly when you are on the main menu. Because under the OSD menu, you can press ↓ and ↑ keys to move the corresponding port. Then press Enter key, the DKVM-IP16 will switch to this input.
Configuring the DKVM-IP16
The DKVM-IP16 default settings
Username: admin
Password: 12345
DHCP: Disabled
IP address: 192.168.1.101
Subnet mask: 255.255.255.0
You can use a Web browser to configure the DKVM-IP16. The computer, which will be used for configuring the KVM switch, should have an IP address in the same range as the DKVM-IP16. In order to enter the Web-based GUI, please open a Web browser and enter the IP address of the KVM switch in the address bar. Then press Enter. When the dialog box appears, enter the username and the password. Press Login.
Note: Press and hold the Reset button on the console panel for 10 seconds to restore the default settings. Wait until resetting the settings is completed (5 seconds), then disconnect and connect the power adapter to the electrical network again. After the device is booted (1 minute), it will be accessible via its default IP address.
Note: You can remotely control the DKVM-IP16 using the 5.0 (V1.5) JRE
(Java Runtime Environment)
program platform. You can download it from the following website:
http://www.java.com/.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>