PORTOR LIGHTING PT-DLS-21-R Series LED 2 in 1 Downlight Instruction Manual

PORTOR LIGHTING PT-DLS-21-R Series LED 2 in 1 Downlight

Product Specifications

• Model: PT-DLS-21-R SERIES
• Variant: PT-DLS-21-R-4I-10W-5CCT

Product Usage Instructions

Installation Instructions

CAUTION: RISK OF ELECTRIC SHOCK. DISCONNECT POWER BEFORE CONNECTING THE FIXTURE. FAILURE TO DO SO MAY PERMANENTLY DAMAGE THE LEDS.

WARNING: DO NOT REMOVE OR ATTEMPT TO REMOVE LEDS.

Safety Precautions

For safety, read and understand instructions completely before starting installation. Electricity should be turned off at the fuse or the circuit breaker box before installing the fixture. All electrical connections must be in accordance with N.E.C. or your local code.

Assembly Instructions

1. Preparing for Installation: Disconnect electrical power before installing or servicing any part of this fixture.
2. This device complies with Part 15 of the FCC rules. Operation is subject to specific conditions.

Package Contents

• LED 2 in 1 Downlight x4
• Wire nuts x2
• ST3x5 Screws x2
• E26 base adapter x1
• Hardwire pigtail x1
• Torsion spring x2
• Cut-out template

Installation (Consult a Qualified Electrician Before Installing)

Can-less Installation (Use Tools to Cut Holes in the Ceiling – 4.3)

1. Turn off the power. Make sure the switch is OFF at the breaker box.
2. Select the location for the fixture and cut the hole in the ceiling using the provided template.
3. Remove the knock out from the junction box.
4. Lay out and connect the wires according to the instructions and desired CCT.
5. Securely connect the hardwire pigtail to the main power line.
6. Feed the supply wires into the knockout and connect the wires accordingly.
7. Place wires inside the junction box and close the cover.
8. Guide the slim microdisk through the ceiling hole until clips snap.

Installation (Continuation)

Retrofit Installation (Suitable for 4 Retrofit Housing)

1. Turn off the power. Make sure the switch is OFF at the breaker box.
2. Pre-select the desired CCT by switching between options.
3. Remove spring attachment from downlight.
4. Install the spring piece using screws into the slot of the downlight.
5. Install the E26 adapter into the CAN socket.
6. Connect wires and gently push the fixture into the recesses CAN.

Frequently Asked Questions

Q: Can I install this fixture without consulting an electrician?

A: It is recommended to consult a qualified electrician before installing to ensure safety and proper installation.

Q: What should I do if I encounter interference issues after installation?

A: Ensure that all connections are secure and follow instructions for selecting the desired CCT to minimize interference.

PT-DLS-21-R-4I-10W-5CCT

CAUTION: RISK OF ELECTRIC SHOCK
DISCONNECT POWER BEFORE CONNECTING THE FIXTURE. FAIL TO DO SO MAY PERMANENTLY DAMAGE THE LEDS.

WARNING
DO NOT REMOVE OR ATTEMPT TO REMOVE LEDS.

SAFETY PRECAUTIONS

FOR SAFETY, READ AND UNDERSTAND INSTRUCTIONS COMPLETELY BEFORE STARTING INSTALLATION. ELECTRICITY SHOULD BE TURNED OFF AT THE FUSE OR THE CIRCUIT BREAKER BOX BEFORE INSTALLING THE FIXTURE. ALL ELECTRICAL CONNECTIONS MUST BE IN ACCORDANCE WITH N. E. C. OR YOUR LOCAL CODE.

ASSEMBLY INSTRUCTIONS

1. PREPARING FOR INSTALLATION: DISCONNECT ELECTRICAL POWER BEFORE INSTALLING OR SERVICING ANY PART OF THIS FIXTURE.
2. THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS:
3. THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND
4. THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING THAT MAY CAUSE UNDESIRED OPERATION.

PACKAGE CONTENTS

INSTALLATION

( CONSULT A QUALIFIED ELECTRICIAN BEFORE INSTALLING )

CAN-LESS INSTALLATION (Use tools to cut holes in the ceiling – 4.3”)

1.  Turn off the power. Make sure the switch is OFF at the breaker box.

2. Select the location for the fixture. Ensure there is enough space for the fixture.
   Note : Ensure that there is no joist on the desired location.

3. Cut the hole in the ceiling using the provided template.
   Note The cut out size should be 6.30 in.

4. Remove the knock out from the junction box using a screwdriver.
5. Locate the switch and power supply wires by opening the power supply box. Pre select the desired CCT by switching between 2700K, 3000K, 3500K, 4000K, 5000K.
6. Connect the hardwire pigtail to the main power line. Black goes to black and white to white. Use the wire nuts provided to ensure there is a secured connection .

7. Feed the supply wires into the knockout.
   Ensure to use a 3/8 in. metal clap connector (not included). Connect the two orange connector and ground wires.

8. Once all wires are connected correctly, place wire inside the junction box and close the junction box cover.

9. Pull the spring clips on the slim microdisk up and gently guide through the ceiling hole until the clips snap.

RETROFIT INSTALLATION

(Suitable for 4” retrofit housing)

1. Turn off the power. Make sure the switch is OFF at the breaker box.

2. Remove spring attachment from downlight

3. Install the spring piece into the slot of the downlight using ST 3×5 screws

4. Pre select the desired CCT by switching between 2700K, 3000K, 3500K, 4000K, 5000K.

5. Install the E26 adapter into the CAN socket

6. Connect the two orange connector and gently push the fixture into the recesses CAN.

www.portorlighting.com

Specification subject to change without notice

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>