SEALEY PEH3001.V2 Industrial PTC Fan Heater Instruction Manual
- June 1, 2024
- SEALEY
Table of Contents
3000W INDUSTRIAL
PTC FAN HEATER, 230V
MODEL NO: PEH3001.V2
PEH3001.V2 Industrial PTC Fan Heater
Thank you for purchasing a Sealey product. Manufactured to a high standard,
this product will, if used according to these instructions, and properly
maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE
OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND
WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE
INSTRUCTIONS SAFE FOR FUTURE USE.
SAFETY
1.1. ELECTRICAL SAFETY
WARNING! It is the user’s responsibility to check the following:
Check all electrical equipment and appliances to ensure that they are safe
before using. Inspect power supply leads, plugs and all electrical connections
for wear and damage. Sealey recommend that an RCD (Residual Current Device) is
used with all electrical products.
Electrical safety information. It is important that the following information
is read and understood:
Ensure that the insulation on all cables and on the appliance is safe before
connecting it to the power supply.
Regularly inspect power supply cables and plugs for wear or damage and check
all connections to ensure that they are secure.
Important: Ensure that the voltage rating on the appliance suits the
power supply to be used and that the plug is fitted with the correct fuse.
DO NOT pull or carry the appliance by the power cable.
DO NOT pull the plug from the socket by the cable.
DO NOT use worn or damaged cables, plugs or connectors. Ensure that any faulty
item is repaired or is replaced immediately by a qualified electrician.
If the cable or plug is damaged during use, switch off the electricity supply
and remove from use.
Ensure that repairs are carried out by a qualified electrician.
If an extension reel is used it should be as short as possible and fully
unwound before connection. A reel with an RCD fitted is preferred since any
appliance plugged into it will be protected. The cable core section is
important and should be at least 1.5mm², but to be absolutely sure that the
capacity of the reel is suitable for this product and for others which may be
used in the other output sockets, we recommend the use of 2.5mm² section
cable.
1.2. GENERAL SAFETY
WARNING! The appliance shall be disconnected from its power source
during service and when replacing parts and, if the removal of the plug is
foreseen, it shall be clearly indicated that the removal of the plug has to be
such that an operator can check from any of the points to which they has
access that the plug remains removed.
WARNING: DO NOT use this heater in small rooms when they are occupied by
persons not capable of leaving the room on their own, unless constant
supervision is provided.
Servicing or maintenance must only be carried out by an authorised service
agent.
Check that the heater is in sound condition and good working order. Take
immediate action to repair or replace damaged parts.
Use recommended parts only. Unapproved parts may be dangerous and will
invalidate the warranty.
DO NOT attempt to repair a damaged heater, contact an authorised service
agent.
WARNING! In order to avoid overheating, DO NOT cover the heater.
1.3. POSITIONING OF HEATER
WARNING: To reduce the risk of fire, keep textiles, curtains, or any
flammable material a min. distance of 1m from the air outlet.
WARNING! DO NOT use the heater near flammable material, liquids, solids,
gases or compressed gas cylinders etc.
Use this heater on a horizontal and stable surface, or fix it to a wall as
applicable.
DO NOT use this heater in the immediate surroundings of a bath, a shower or a
swimming pool.
DO NOT place the heater up against any surface such as a wall, door or
furniture etc.
The heater must not be located immediately below a socket outlet.
DO NOT place the heater on a raised surface or anywhere where it could topple
over.
DO NOT get the heater wet or use in areas of high condensation.
DO NOT allow the power lead to touch hot surfaces.
DO NOT connect the heater to a timer device or other equipment than can
automatically switch the heater on or off.
DO NOT operate the heater when you are tired or under the influence of
alcohol, drugs or intoxicating medication.
DO NOT stand on the heater.
DO NOT use the heater with wet hands or when there is water on the power cord.
DO NOT use the heater for anything other than its intended purpose. It is
designed to provide heat in enclosed areas such as workshops and other
industrial areas. It is not suitable for drying clothes or laundry.
Position the heater at least a minimum of 1m at the front, rear and sides from
any walls or objects.
If an extension cable is required it must be of the same cross section as the
heater cable. It must be as short as possible and fully unwound.
Ensure that the heater is correctly turned off when not in use and store in a
safe, dry, childproof location.
1.4. OPERATIONAL PRECAUTIONS
The heater must only be used by people who have read these instructions and
have been trained in its use.
DO NOT obstruct the air inlet and outlet sections of the heater.
WARNING! In order to avoid overheating, DO NOT cover the heater.
DO NOT use the heater without the grille fitted.
DO NOT use if the heater has been dropped.
DO NOT use if there are visible signs of damage to the heater.
DO NOT touch the heater casing or grille when first switched off, as these
will be very hot and will take time to cool.
NOTE: Children of less than 3 years should be kept away unless supervised
continuously.
Children aged from 3 years and less than 8 years shall only switch on/off the
appliance provided that it has been placed or installed in its intended normal
operating position and they have been given supervision or instruction
concerning use of the appliance in a safe way and understand the hazards
involved. Children aged from 3 years and less than 8 years shall not plug in,
regulate and clean the appliance or perform user maintenance.
CAUTION: Some parts of this product can become very hot and cause burns.
Particular attention has to be given where children and vulnerable people are
present.
NOTE: The heater must not be located immediately below a socket output.
INTRODUCTION
Industrial fan heaters with PTC heat conducting ceramic elements to achieve an instant, totally dry heat with no condensation, no gas, no fumes and no smell. Ambient room thermostat maintains temperature at a preset level. Ideal for industrial applications with two heat settings or fan only. PEH3001 Supplied without plug.
SPECIFICATIONS
Model: ……………………………………………….PEH3001.V2
Heated Area: …………………………………………………. 60m³
Output: ……………………………………………….10,000Btu/hr
Plug Type:……………………………………………… Bare Wire
Power Supply Cable Length: …………………………… 1.3m
Power: ………………………………………………. 1500/3000W
Supply:………………………………………………… 230V – 16A
IMPORTANT! This unit is designed to raise the ambient temperature of an entire room, the temperature of the air coming out of the front of the heater will be warmer than the general temperature of the room, but there may not be a significant increase due to the large volume of air passing over the element. For the same reason, the element is hot during operation, but does not glow visibly. The room temperature depends on room size, insulation and the ambient temperature, which will increase as the room gets warmer.
OPERATION (FIG.1)
4.1. Position heater in an upright position on a firm surface and at a safe
distance from any obstructions, flammable substances etc. Keep to a minimum of
1m clearance at the rear and sides, and 2m clearance at the front.
4.2. Connect the heater to a suitable mains supply.
4.3. Set the thermostat dial to the maximum setting (fully clockwise).
4.4. The heater will switch on when the power setting selector is set to one
of the two power settings.
NOTE: It will take up to three minutes for the heater to reach optimum
temperature.
4.5. Once the room reaches the required temperature, heating element will stop
working and the fan will stop. Once the temperature decreases, the heating
element and fan will restart working automatically and thus keep the room
temperature constant.
4.6. For fan only operation, turn the power/fan selector to the fan only
setting and set the thermostat to its minimum setting.
4.7. When not in use, disconnect the heater from the mains supply. Store it in
a safe, dry, childproof location.
MAINTENANCE
WARNING! Before attempting any maintenance, ensure that the unit is
unplugged from the mains power supply and that it has cooled down.
5.1. Clean the heater with a soft dry cloth only. DO NOT use abrasives or
solvents.
5.2. Periodically check the heater grille to ensure that it is not blocked.
5.3. If the supply cord is damaged, it must be replaced by the manufacturer,
its service agent or similarly qualified persons in order to avoid a hazard.
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools,
accessories and packaging should be sorted, taken to a recycling centre and
disposed of in a manner which is compatible with the environment. When the
product becomes completely unserviceable and requires disposal, drain any
fluids (if applicable) into approved containers and dispose of the product and
fluids according to local regulations.
WEEE REGULATIONS
Dispose of this product at the end of its working life in compliance with the
EU Directive on Waste Electrical and Electronic Equipment (WEEE). When the
product is no longer required, it must be disposed of in an environmentally
protective way. Contact your local solid waste authority for recycling
information.
Note: It is our policy to continually improve products and as such we
reserve the right to alter data, specifications and component parts without
prior notice. Please note that other versions of this product are available.
If you require documentation for alternative versions, please email or call
our technical team on technical@sealey.co.uk
or 01284 757505.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is
required for any claim.
Information requirements for electric local space heaters
Model identifier(s): PEH3001 v2
Item| Symbol| Value| Unit| Item| Unit
Heat output| Type of heat input, for electric
storage local space heaters only (select one)
Nominal heat output| | 3.000| kW| Manual heat charge control, with integrated
thermostat| Yes No
Minimum heat output (indicative)*
- Enter figure or NA
| | 1.500| kW| Manual heat charge control with room and/or outdoor temperature
feedback| Yes No
Maximum continuous heat output| | 3.000| kW| Electronic heat charge control
with room and/or outdoor temperature feedback| Yes No
| Fan assisted heat output| Yes No
Auxiliary electricity consumption| Type of heat
output/room temperature control (select one)
At nominal heat output| | NA| kW| Single stage heat output and no room
temperature control| Yes No
At minimum heat output| | NA| kW| Two or more manual stages, no room
temperature control| Yes No
In standby mode| | NA| kW| With mechanic thermostat room temperature control|
Yes No
| With electronic room temperature control| Yes No
Electronic room temperature control plus day timer| Yes No
Electronic room temperature control plus week timer| Yes No
Other control options (multiple selections possible)
Room temperature control, with presence
detection
| Yes No
Room temperature control, with open window detection| Yes No
With distance control option| Yes No
With adaptive start control| Yes No
With working time limitation| Yes No
With black bulb sensor| Yes No
Contact details: Sealey Group, Kempson Way, Suffolk Business Park, Bury St
Edmunds, Suffolk, IP32 7AR. www.sealey.co.uk
v1
ERP Table 2
Sealey Group, Kempson Way,
Suffolk Business Park,
Bury St Edmunds,
Suffolk. IP32 7AR
01284 757500
sales@sealey.co.uk
www.sealey.co.uk
© Jack Sealey Limited
Original Language Version
PEH3001.V2 Issue 2 (1,F) 07/11/23
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>