SEALEY CST989.V3 Sack Truck 3-in-1 Pneumatic Tyres Instruction Manual

SEALEY CST989.V3 Sack Truck 3-in-1 Pneumatic Tyres

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance.

IMPORTANT : PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

SAFETY

• Always load evenly with the centre of gravity of the load as near the centre and rear of the plate as possible.
• Obtain additional support for large or wide loads to prevent tipping.
• DO NOT overload the truck – see Specification.
• DO NOT leave unattended, especially when loaded, unless the wheels are chocked or the truck is otherwise secured.
• DO NOT use truck on uneven ground and DO NOT run over curbs or steps – use a ramp.
• DO NOT allow others to ride on the truck.
• DO NOT use the truck if any part is damaged, paying particular attention to the wheels.

INTRODUCTION

Tubular steel framework with heavy-duty pneumatic tyres allows transport of load over rough terrain. Suitable for use as a traditional sack truck or at 45° with support castors in position. For maximum load carrying capability use in horizontal position. Features fold out load restrainer for use when truck is in horizontal position. Adapts between configurations in seconds.

SPECIFICATION

• Model No:…………………………………………… CST898.V3
• Capacity:……………………………………………………. 250kg
• Height(s):………………………………………………… 1275mm
• Overall Width:……………………………………………. 600mm
• Platform Depth:…………. Fixed; 300mm, Folding; 620mm
• Wheel Size:……………………………………………. Ø250mm
• Wheel Width:………………………………………………. 90mm

ASSEMBLY

1. Make sure the axle is free from dust and dirt to allow free rotation of the wheel.
2. Place spacer (fig.1.2) onto axle first. Slide the wheel (fig.1.3) onto the axle (fig.1.1) followed by a washer (fig.1.4). Push a split pin (fig.1.5) through the hole in the end of the axle and bend over the ends in order to secure the whole assembly.
3. Push axle through frame, repeat for the other side.

OPERATION

1. The truck can be used in three different configurations as shown i n (figs.2.3 & 4).

2. Standard Sack Truck. To operate as a two wheel sack truck ensure that the castor wheels and secondary frames are secured flat against the main frame. The castor wheels should be turned sideways and the loop handle should be resting in the lower stowage bracket with the locking pin in place, as shown in (fig.2).

3. Sack Truck supported at 45°. To use as a 45° sack truck release the secondary frame and wheels by removing the locking pin from the lower bracket. Take hold of the loop handle with one hand and tip the truck towards you with the other hand until the loop handle can be placed into the upper bracket and secured with the locking pin, as shown in (fig.3).

4. Flat bed truck. To use as a flat bed truck release the secondary frame and castor wheels by removing the locking pin from the securing bracket. Take hold of the loop handle and tip it towards you so that it clears the square tube at the top of the main frame between the black handles. With the other hand lower the main frame until the square tube comes to rest on the slotted bracket about 12cm above the castor wheels, as shown in (fig.4).
   Fold up the load restraint at the other end of the frame until it rests against the platform.

5. Manoeuvre the loaded trolley using the loop handle only. DO NOT lift the truck by the black handles when used in flat bed configuration.

6. WARNING! When changing truck positions keep fingers well clear of all pinch points.

ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations.

Note : It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
Important : No Liability is accepted for incorrect use of this product.
Warranty : Guarantee is 12 months from purchase date, proof of which is required for any claim.

01284 757500
sales@sealey.co.uk
www.sealey.co.uk

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>