Keilton PPA104S LED Controller User Manual
- June 1, 2024
- Keilton
Table of Contents
Keilton PPA104S LED Controller
Specifications:
- Product Name: 20A Zone Controller
- Model: PPAX04SYYYY
- Max Load: 20A
- Operating Voltage: 120-277VAC, 50/60Hz
- Dimming Port: 0-10V (24-16AWG)
- Compatibility: Keilton lighting control system
Product Usage Instructions
Installation:
- Call a licensed electrician for installation.
- Drill a 1/2″ knockout in the sheet metal for PPA104S installation, ensuring it is securely fixed.
- Screw in the sensor into the receptacle and ensure a tight connection.
- Make sure the rubber gasket touches the outside surface of the fixture.
- Refer to the wiring diagram provided for installation.
- Restore power back to the source.
- Commission the sensor via the Keilton App.
Control and App Installation:
To control lights with your phone, follow these steps:
- Download the Keilton App by scanning the QR code provided.
- Follow the instructions on how to control lights using the Keilton App.
FAQ:
How to Install Keilton APP?
Scan below QR code to download the APP.
FCC Statement:
This device complies with Part 15 of the FCC rules. Operation is subject to
certain conditions to avoid interference.
- Reorient the receiving antenna if needed.
- Increase the separation between the equipment and receiver.
- Connect the equipment to a different circuit than the receiver.
- If any issues, consult with a dealer or experienced technician.
The distance between user and products should be no less than 20cm. The EUT is for indoor use only.
20A Zone Controller
PPAX04SYYYYUserManual
WARNING: May result in serious injury or death. Turn off power at circuit breaker before installing the unit.
FEATURES
- Please call a licensed electrician for installation.
- Drill 1/2″ KO in the sheet metal for PPA104S installation, make sure the PPA104S well fixed in the luminaire. the PPA104S well fixed in the luminaire.
- Screw in the sensor into the receptacle and make sure the connection is tight.
- Ensure the rubber gasket touches the outside surface of the fixture.
- Please refer below diagram for Wiring.
- Return powerback to source.
- Commissioned the sensor via Keilton App.
WIRING
- Note: PPA104S MAX Load 20A, Sink Current Max.48.5mA of the dimming port.
- TIPS: This Bluetooth device is compatible with Keilton lighting control system only.
How to Install Keilton APP?
Scan below QR code for downloading the APP.
How to Control Lights with a Phone?
Scan to download Keilton APP instruction
WARRANTY INFORMATION
Our company warranties this product to be free of defects in materials and
workmanship for a period of five(5) years. There are no obligations or
liabilities on the par of our company for consequential damages arising out
of, or in connection with, the use or performance of this product or other
indirect damages with respect to loss of property, revenue or profit, or cost
of removal, installation or reinstallation.
Contact: sales@litetrace.com
FCC Statement
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class 3 digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try correct the interference by one or more of the following measures:
- Reorient the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into and outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for
compliance could void your authority to operate the equipment.
The distance between user and products should be no less than 20cm
The EUT is In door use only
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>