Keilton WF20R 20A Plug Load Controller User Manual

June 13, 2024
Keilton

20A Plug Load Controller
WF20R V1.0 User Manual

WARNING : May result in serious injuryn or death. Turn off power at circuit breaker before installing the unit.
To be installed and/or used in accordance with appropriate electrical codes and regulations. Exercise extreme caution when using Keilton devices to control appliances. Operation of the Keilton device may be in a different room than the controlled appliance, also an unintentional activation may occur if the wrong button on the remote is pressed. Keilton devices may automatically be powered on due to timed event programming. Depending upon the appliance, these unattended or unintentional operation could possibly result in a hazardous condition.
Keilton enabled devices should never be used to supply power to, or control the On/Off status of medical and/or life support equipment.
If you are unsure or uncomfortable about performingthe installation, please consult a qualified electrician.

INSTALLATION

This receptacle may be used in new installations or to replace an existing wall receptacle.

WIRING

Keilton WF20R 20A Plug Load Controller -

  • Wire Strip Length ; 16 mm(5/8 in)
  • The device shall install in a standard outlet box.
  • For retrofit applications, remove wall plate.
  • Verify power is OFF before continuing.
  • Remove the existing receptacle from the box.
  • Disconnect the wiringfrom the existing receptacle.
  • Connect the WF2OR receptacle as shown in the wiring diagram: Black lead to hot wire, white lead to neutral wire, green lead to ground wire.
  • Check connections to be sure they are tight and no bare conductors are exposed.
  • Insert the WF20R receptacle into the outlet box carefully.
  • Make sure the WF2OR receptacle to the box usingthe supplied screws.
  • Attach the wall plate.
  • Restore power at the circuit breaker and test the system.

OPERATION

This receptacle may be used in new installations or to replace an existing wall receptacle .

Keilton WF20R 20A Plug Load Controller - program

  • Always-on Receptacle: always connected, not be controlled by button or Keilton APP, switch or program button.
  • Keilton Controlled Receptacle: can be turned on/off by Keilton APP, switch or program button.
  • Blue LED indicator: flashes on powering on or receiving wireless commands.
  •  Program Button:
  • Short press: turn on/off controlled receptacle.
  • Long press for 6 seconds: reset the controller to factory settingto be ready added by Keilton APP. You will hear gentle clicks of the relay when the controller being reset.

ADD THE CONTRO TO KEILTON APP

Keilton WF20R 20A Plug Load Controller - program 1

Go to Lights page on Keilton APP, click the `+’ button to start addingthe controller. Check the controller, click “Add” and confirm to add in the dialog box to add the controller. Please reset the controller if it does not show up in the process.

NAMING AND TURNING ON/OFF

Keilton WF20R 20A Plug Load Controller - program
2

Long press the controller icon on Lights page to bring out the dimming page. You may rename the controller, input the wattage of the load, and turn on/off the controller. You may click the icon on Lights page to turn on/off the controller. The icon shows the current status of the controller. You may also add the controller into a group, a scene, associate it with switches, schedules to manually or automatically turn on/off it.

GROUPING AND LINKING WITH OTHER KEILTON SENSORS

Keilton WF20R 20A Plug Load Controller - program 3

Click the sensor setting button on controller’s dimming page.
Enable the motion sensor function for the controller.
Set the appropriate parameters and click ‘Save’ to send it to the controller.
You may also add the controllerto a group with other Keilton sensors, enable linkage so it can be automatically controlled by motion sensors in the same group.
You need to follow the steps to:

  •  Enable the motion function on controller.
  • Add the controller to a group with other sensors.
  • Set the sensor parameters for the sensors and controller.
  • Enable the linkage forthis group.

GROUPING AND LINKING WITH OTHER KEILTON SENSORS

Keilton WF20R 20A Plug Load Controller - program 4

Create a group, check the members of this group and save it. Set the appropriate linkage level and enable the ‘Link’ on this group. Now when the sensors in this group is triggered, the controller will be linked to turn on. It will be turned off when sensors timed out. There is an ‘A’ in the icon to indicate that the controller is in “auto” mode and controlled by sensors.

How to Install Keilton APP?
Scan below QR code for downloadingthe APP.

|
---|---
https://itunes.apple.com/cn/app/keilton/id1423982372?mt=8| https://play.google.com/store/apps/details?id=com.litetrace.keilton.bluetooth.light3

How to Control Lights with a Phone?
Scan to download Keilton APP instruction

https://keilton.s3.amazonaws.com/Keilton+App+Instruction.pdf

WARRANTY INFORMATION

Our company warranties this product to be free of defects in materials and workmanship for a period of five(5) years.There are no obligations or liabilities on the part of our company for consequential damages arising out of, or in connection with, the use or performance of this product or other indirect damages with respect to loss of property, revenue or profit, or cost of removal, installation or reinstallation. Contact: sales@litetrace.com

FCC STATEMENT This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try correct the interference by one or more of the following measures:

  • Reorient the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into and outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.

The distance between user and products should be no less than 20cm

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals