BriTeQ BT-THEATRE 261FC Powerful “6 in 1” FULL COLOR LED Theater Fresnel User Manual

BriTeQ BT-THEATRE 261FC Powerful “6 in 1” FULL COLOR LED Theater Fresnel

DISPOSAL OF THE DEVICE
Dispose of the unit and used batteries in an environment-friendly manner according to your country regulations.

OPERATION MANUAL
Thank you for buying this Briteq® product. To take full advantage of all possibilities and for your own safety, please read these operating instructions very carefully before you start using this unit.

FEATURES

• A powerful “6-IN-1” FULL COLOR LED theater Fresnel with manual 15° ~ 50° zoom.
• No more need for separate white and color projectors, BT-THEATRE 261FC does it all:
• Perfect WHITE with high CRI > 93Ra and several CCT presets
• Rich COLOR selection with color presets following the LEE® numbering!
• Thanks to the Color Calibration System, there are no more the color differences between different batches!
• Different CCT presets for white: 1800K, 3000K, 4000K, …, 8000K
• Very realistic redshift emulation during projector dimming.
• The 94 most used color presets (LEE® numbering) can be selected!
• The 200watt 6-color RGBALC-LED (Red, Green, Blue, Amber, Lime, Cyan) assures a very wide color gamut.
• Very silent operation: heat-pipe technology with low noise cooling fan and different presets (live, studio, …)
• DMX-controlled: 10 different channel modes (1 to 21 channels) for maximum flexibility.
• Prepared for wireless DMX: just plug-in an optional WTR-DMX DONGLE ! (Briteq® code: 4645)
• RDM-functionality for easy remote setup: DMX addressing, channel mode, …
• Flicker free TV-recordings thanks to the adjustable high LED-refresh rate!
• Four dimmer settings with different behavior & speed.
• Standalone mode: manual control for dimming, color/CCT presets, green/magenta shift & zoom.
• OLED-display to navigate easily through the setup menu!
• In case of DMX failure, you can choose between manual, blackout and freeze mode.
• Lock function to avoid unwanted altering of the settings.
• Eight-leaf barndoor included.
• Rugged extruded aluminum housing.
• 3 & 5pin DMX in/outputs + PowerCON® compatible in/outputs for easy daisy chaining.

BEFORE USE

• Before you start using this unit, please check if there’s no transportation damage. Should there be any, do not use the device and consult your dealer first.
• Important: This device left our factory in perfect condition and well packaged. It is absolutely necessary for the user to strictly follow the safety instructions and warnings in this user manual. Any damage caused by mishandling is not subject to warranty. The dealer will not accept responsibility for any resulting defects or problems caused by disregarding this user manual.
• Keep this booklet in a safe place for future consultation. If you sell the fixture, be sure to add this user manual.

Check the contents:
Check that the carton contains the following items:

• English operating instructions, other languages can be downloaded from our website.
• BT-THEATRE 261FC
• Color frame
• Eight-leaf barndoor
• PowerCON® compatible mains cable

SAFETY INSTRUCTIONS

CAUTION: To reduce the risk of electric shock, do not remove the top cover. No user-serviceable parts inside. Refer servicing to qualified service personnel only.
The lightning flash with arrowhead symbol within the equilateral triangle is intended to alert the use or the presence of un-insulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock.

The exclamation point within the equilateral triangle is intended to alert the user to the presence of important operation and maintenance (servicing) instructions in the literature accompanying this appliance.
This symbol means: indoor use only
This symbol means: Read instructions
This symbol determines the minimum distance from lighted objects. The minimum distance between light-output and the illuminated surface must be more than 1 meters

CAUTION: Do not stare at operating lamp. May be harmful to the eyes.

• To protect the environment, please try to recycle the packing material as much as possible.
• To prevent fire or shock hazard, do not expose this appliance to rain or moisture.
• To avoid condensation to be formed inside, allow the unit to adapt to the surrounding temperatures when bringing it into a warm room after transport. Condense sometimes prevents the unit from working at full performance or may even cause damages.
• This unit is for indoor use only.
• Don’t place metal objects or spill liquid inside the unit. Electric shock or malfunction may result. If a foreign object enters the unit, immediately disconnect the mains power.
• Locate the fixture in a well-ventilated spot, away from any flammable materials and/or liquids. The fixture must be fixed at least 50cm from surrounding walls.
• Don’t cover any ventilation openings as this may result in overheating.
• Prevent use in dusty environments and clean the unit regularly.
• Keep the unit away from children.
• Inexperienced persons should not operate this device.
• Maximum safe ambient temperature is 40°C. Don’t use this unit at higher ambient temperatures.
• Make sure the area below the installation place is free from unwanted persons during rigging, de-rigging and servicing.
• Allow the device about 10 minutes to cool down before to start servicing.
• Always unplug the unit when it is not used for a longer time or before to start servicing.
• The electrical installation should be carried out by qualified personal only, according to the regulations for electrical and mechanical safety in your country.
• Check that the available voltage is not higher than the one stated on the unit.
• The power cord should always be in perfect condition. Switch the unit immediately off when the power cord is squashed or damaged. It must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
• Never let the power-cord come into contact with other cables!
• This fixture must be earthed in order to comply with safety regulations.
• Don’t connect the unit to any dimmer pack.
• Always use an appropriate and certified safety cable when installing the unit.
• In order to prevent electric shock, do not open the cover. Apart from the mains fuse there are no user serviceable parts inside.
• Never repair a fuse or bypass the fuse holder. Always replace a damaged fuse with a fuse of the same type and electrical specifications!
• In the event of serious operating problems, stop using the fixture and contact your dealer immediately.
• The housing and the lenses must be replaced if they are visibly damaged.
• Please use the original packing when the device is to be transported.
• Due to safety reasons it is prohibited to make unauthorized modifications to the unit.

Important: Never look directly into the light source! Don’t use the effect in the presence of persons suffering from epilepsy.

DESCRIPTION

1. MAINS INPUT: equipped with PowerCON® compatible connectors. Connect the supplied mains cable or any PowerCON® compatible extension cable here.
2. MAINS OUTPUT: used to daisy chain the power to several other projectors. Always pay attention to the maximum load while adding projectors! Special Multi cables (PowerCON® + DMX XLR-cables are optionally available: see our website!)
3. FOCUS KNOB: used to adjust the beam angle manually.
4. MAINS FUSE: protects the unit in case of electrical problems, always use the prescribed fuse!
5. DMX IN/OUT: both 3pin and 5pin in/outputs are available to daisy chain the projector with other units that will be controlled by a DMX-controller.
6. M-DMX INPUT: Please note that this USB-connector is NOT used for updates or to connect the unit to a PC! Instead this USB-connector makes it very easy to add wireless DMX to the unit! Just add the (optional) WTR-DMX DONGLE from BRITEQ® and you will get wireless DMX! Moreover, you will be able to connect other DMX-controlled equipment to the DMX-output so you can share the wireless DMX function with all connected units! No extra settings to be made in the setup menu, just follow the procedure in the user manual supplied with the WTR-DMX DONGLE from BRITEQ®. The separate WTR-DMX DONGLE is available from WWW.BRITEQ-LIGHTING.COM (order code: 4645)
7. DISPLAY: shows the various menus and the selected functions.
8. MENU-button: used to enter and exit the setup menu or to jump to a higher level in the setup menu.
9. ENTER-button: used to select a menu option or confirm a setting.
10. ▲-button: used to go to the previous menu option or to increase a parameter value.
11. ▼-button: used to go to the next menu option or to decrease a parameter value.
12. DIMMER KNOB: turn the encoder to change the light output manually. Press the encoder for 2 seconds if you want to save the new light output value for future use.
13. CONTROL KNOB: this knob has several functions.
    • CHANGE CCT: press the encoder until the display shows [CCT]. Turn the encoder to select the desired CCT-preset. Press the encoder for 2 seconds if you want to save the new CCT for future use. Press the encoder again shortly to select the next function.
    • CHANGE GREEN/MAGENTA CORRECTION: press the encoder until the display shows [TINT]. Turn the encoder to select the desired color correction. Press the encoder for 2 seconds if you want to save the new correction for future use. Press the encoder again shortly to select the next function.
    • COLOR PRESETS: press the encoder until the display shows [COLOR PRESET]. Turn the encoder to select the desired color preset. Press the encoder for 2 seconds if you want to save the new color preset for future use. Press the encoder again shortly to select the next function.
14. HANDLE: used for aligning the spotlight. Can also be used to attach the safety cable during installation, see paragraph “overhead rigging”.
15. HANGING BRACKET: with a knob on both sides to fasten the unit in the desired position. You can use the hole in the center of the bracket to fix a hook or truss clamp.
16. LOCKING CLIP: The clip is used to keep the barndoor and color frame in place. Push the clip aside to open it.
17. BARN DOOR: they facilitate shaping of the beam of light from the fixture, and prevent the distinctive scatter of light created by the Fresnel lens from spilling into areas where it is not wanted, such as the eyes of audience members. Just rotate the barndoor in the desired position.

SETUP MENU / HOW TO SETUP

With the setup menu you can fully configure the projector. All settings are preserved when the unit is disconnected from the mains.
■ [MENU] button: press to enter / leave the setup menu.
► [ENTER] button: press to select / confirm or store the current menu option or value.
▲/▼ [UP/DOWN] button: press to navigate the setup menu or change a value.

CCT (4CH)
EASY (6CH)
HSI (6CH)
HSIC FULL (12CH)
CMY (12CH)
FULL 8bit (14CH)
FULL 16bit(21CH)
RAW 8bit (9CH)
RAW 16bit (16CH)
FIXTURE Set|

NO DMX Mode

| Freeze
Blackout
Blackout delayed
Manual

DIM Curve

| Linear
Square
Inv. Square
S-Curve
DIM Behavior| HALOGEN / LED
Red Shift| ON /OFF
LED PWM-freq| 1200Hz → 25kHz
1CH CCT preset| 1800K → 8000K
Color Cal| ON /OFF
FAN Set| Low Auto High
DISPLAY Set| AUTO LOCK| ON /OFF
noDMX blink| ON /OFF
Temp °C/F| Celcius/Fahrenheit
DEFAULTS| Factory Settings| LOAD ?
USER Settings| LOAD / SAVE ?
INFORMATION| Total LED Hours| xxxx Hrs
Last JOB hours| xxxx Hrs
LED Temp.| xxx °C / F
ERROR info| xxxxxxxx
Model Name| BT-THEATRE 261FC
Firmware V.| V x.xx
RDM UID| 0x21220043xxxx

OVERHEAD RIGGING

Important: The installation must be carried out by qualified service personal only. Improper installation can result in serious injuries and/or damage to property. Overhead rigging requires extensive experience! Working load limits should be respected, certified installation materials should be used, the installed device should be inspected regularly for safety.

• Make sure the area below the installation place is free from unwanted persons during rigging, de-rigging and servicing.
• Locate the fixture in a well-ventilated spot, far away from any flammable materials and/or liquids. The fixture must be fixed at least 50cm from surrounding walls.
• The device should be installed out of reach of people and outside areas where persons may walk by or be seated.
• Before rigging make sure that the installation area can hold a minimum point load of 10times the device’s weight.
• Always use a certified safety cable that can hold 12times the weight of the device when installing the unit. This secondary safety attachment should be installed in a way that no part of the installation can drop more than 20cm if the main attachment fails.
• The device should be well fixed; a free-swinging mounting is dangerous and may not be considered!
• Don’t cover any ventilation openings as this may result in overheating.
• The operator has to make sure that the safety-relating and machine-technical installations are approved by an expert before using them for the first time. The installations should be inspected every year by a skilled person to be sure that safety is still optimal.

ELECTRICAL INSTALLATION

Important: The electrical installation should be carried out by qualified personal only, according to the regulations for electrical and mechanical safety in your country.

Electrical installation for two or more units in DMX-mode:

• The DMX-protocol is a widely used high speed signal to control intelligent light equipment. You need to “daisy chain” your DMX controller and all the connected units.
• Pin layout XLR-3pin: Pin1 = GND ~ Pin2 = Negative signal (-) ~ Pin3 = Positive signal (+)
• To prevent strange behavior of the light effects, due to interferences, you must use a 90Ω to 120Ω terminator at the end of the chain. Never use Y-splitter cables, this simply won’t work!
• Make sure that all units are connected to the mains.
• Each unit in the chain needs to have its proper starting address so it knows which commands from the controller it has to decode.

Electrical installation for two or more units in WIRELESS DMX:
Same procedure as for a standard DMX-setup but 2 possibilities:

RDM FUNCTIONS / REMOTE SETUP

RDM means “Remote Device Management”. This projector works with a brief set of RDM-functions which means that it can setup a bi-directional communication with an RDM-compatible DMX-controller. Some of these functions are briefly explained below, others will be added in the future.

• The DMX-controller sends out a “discovery command”, all RDM devices respond and send their unique device ID.

• The DMX-controller asks each RDM device for some basic data so it knows which devices are connected.
  The projector will respond:

• Device name: BT-THEATRE 261FC

• Manufacturer: Briteq®

• Category: LED Dimmer

• Firmware: x.x.x.x (firmware version of the projector)

• DMX address: xxx (current DMX start address of the projector)

• DMX footprint: xx (number of DMX-channels used by the projector)

• Personality: xx (current personality [or DMX-working mode] used by the projectors)

• The DMX-controller can send certain commands to each RDM device which allow remote setup of the units. Thanks to this the projector can be setup remotely.

The following functions can be managed remotely:
No more need to take a ladder and set all units one by one!

• DMX START ADDRESS: The start address can be set remotely from 001 to xxx.
• PERSONALITY: The DMX working mode (DMX-chart) can be set remotely.

These 2 functions make it possible to prepare a complete DMX-patch of all projectors on the DMX-controller and send these data to all projectors at once. More functions will be added later.

DMX CHARTS

Personalities: Dim (1ch), CCT (4ch), Easy (6ch), HSI (6ch), HSIC Full (12ch), CMY (12ch), Full 8bit (14ch), Full 16bit (21ch), RAW 8bit (9ch), RAW 16bit (16ch)

SIMPLE CHART

DIM| CCT| EASY| HSI| HSIC FULL| CMY| FULL

8bit

| FULL

16bit

| RAW

8bit

| RAW

16bit

| VALUE| FUNCTION
---|---|---|---|---|---|---|---|---|---|---|---
1CH| 4CH| 6CH| 6CH| 12CH| 12CH| 14CH| 21CH| 9CH| 16CH|  |
1| 1| 1| 1| 1| 1| 1| 1| 1| 1| 000-255| MASTER DIMMER
 |  |  |  | 2| 2|  | 2|  | 2| 000-255| MASTER DIMMER FINE
 | 2| 2| 2| 3| 3| 2| 3| 2| 3| 000-255| STROBE
 | 3| 3|  | 4| 4| 3| 4|  |  | 000-255| CCT (Color temperature)
 | 4|  |  | 5| 5| 4| 5|  |  | 000-255| TINT: GREEN / MAGENTA

correction

 |  | 4|  | 6| 6| 5| 6|  |  | 000-255| X-FADE: CCT ↔ COLOR
 |  | 5|  | 7| 7| 6| 7|  |  | 000-255| COLOR FILTER PRESETS (White

point = 3200K)

 |  | 6|  | 8| 8| 7| 8|  |  | 000-255| COLOR FILTER FADE-OVER TIME
 |  |  | 3| 9|  |  |  |  |  | 000-255| HUE
 |  |  | 4| 10|  |  |  |  |  | 000-255| HUE FINE
 |  |  | 5| 11|  |  |  |  |  | 000-255| SATURATION
 |  |  |  |  |  | 8| 9| 3| 4| 000-255| RED
 |  |  |  |  |  |  | 10|  | 5| 000-255| RED FINE
 |  |  |  |  |  | 9| 11| 4| 6| 000-255| GREEN
 |  |  |  |  |  |  | 12|  | 7| 000-255| GREEN FINE
 |  |  |  |  |  | 10| 13| 5| 8| 000-255| BLUE
 |  |  |  |  |  |  | 14|  | 9| 000-255| BLUE FINE
 |  |  |  |  |  | 11| 15| 6| 10| 000-255| AMBER
 |  |  |  |  |  |  | 16|  | 11| 000-255| AMBER FINE
 |  |  |  |  |  | 12| 17| 7| 12| 000-255| LIME
 |  |  |  |  |  |  | 18|  | 13| 000-255| LIME FINE
 |  |  |  |  | 9| 13| 19| 8| 14| 000-255| CYAN
 |  |  |  |  |  |  | 20|  | 15| 000-255| CYAN FINE
 |  |  |  |  | 10|  |  |  |  | 000-255| MAGENTA
 |  |  |  |  | 11|  |  |  |  | 000-255| YELLOW
 |  |  | 6| 12| 12| 14| 21| 9| 16| 000-255| CONTROL (active after 3s)

FULL CHART

DIM| CCT| EASY| HSI| HSIC FULL| CMY| FULL

8bit

| FULL

16bit

| RAW

8bit

| RAW

16bit

| VALUE| FUNCTION
---|---|---|---|---|---|---|---|---|---|---|---
1| 1| 1| 1| 1| 1| 1| 1| 1| 1| 000-255| MASTER DIMMER
 |  |  |  | 2| 2|  | 2|  | 2| 000-255| MASTER DIMMER FINE
 | ****

2

| ****

2

| ****

2

| ****

3

| ****

3

| ****

2

| ****

3

| ****

2

| ****

3

| STROBE
000-005| Open (no strobe)
006-125| Normal strobe (slow → fast)
126-135| Open (no strobe)
136-255| Random strobe (slow → fast)
 | 3| 3|  | 4| 4| 3| 4|  |  | CCT (Color temperature)
000-009| NO FUNCTION
010-255| 1800K ↔ 8000K
 | ****

4

|  |  | ****

5

| ****

5

| ****

4

| ****

5

|  |  | TINT: GREEN / MAGENTA correction
000-016| NEUTRAL / no effect
017-116| MAGENTA 99% ↔ 1%
117-139| NEUTRAL / no effect
140-239| GREEN 1% ↔ 99%
240-255| GREEN 100%
 |  | 4|  | 6| 6| 5| 6|  |  | 000-255| X-FADE: CCT ↔ COLOR
 |  | ****

5

|  | ****

7

| ****

7

| ****

6

| ****

7

|  |  | COLOR FILTER PRESETS (White point = 3200K)
000-005| NO FUNCTION – No Filters, color channels used
006-193| Color filter presets SEE NEXT TABLE for details!
194-195| USER Color 1
196-197| USER Color 2
198-199| USER Color 3
200-201| USER Color 4
202-204| USER Color 5
205-255| COLOR SCROLL: slow ↔ fast
 |  | 6|  | 8| 8| 7| 8|  |  | 000-255| COLOR FILTER FADE-OVER TIME
 |  |  | 3| 9|  |  |  |  |  | 000-255| HUE
 |  |  | 4| 10|  |  |  |  |  | 000-255| HUE FINE
---|---|---|---|---|---|---|---|---|---|---|---
 |  |  | 5| 11|  |  |  |  |  | 000-255| SATURATION
 |  |  |  |  |  | 8| 9| 3| 4| 000-255| RED
 |  |  |  |  |  |  | 10|  | 5| 000-255| RED FINE
 |  |  |  |  |  | 9| 11| 4| 6| 000-255| GREEN
 |  |  |  |  |  |  | 12|  | 7| 000-255| GREEN FINE
 |  |  |  |  |  | 10| 13| 5| 8| 000-255| BLUE
 |  |  |  |  |  |  | 14|  | 9| 000-255| BLUE FINE
 |  |  |  |  |  | 11| 15| 6| 10| 000-255| AMBER
 |  |  |  |  |  |  | 16|  | 11| 000-255| AMBER FINE
 |  |  |  |  |  | 12| 17| 7| 12| 000-255| LIME
 |  |  |  |  |  |  | 18|  | 13| 000-255| LIME FINE
 |  |  |  |  | 9| 13| 19| 8| 14| 000-255| CYAN
 |  |  |  |  |  |  | 20|  | 15| 000-255| CYAN FINE
 |  |  |  |  | 10|  |  |  |  | 000-255| MAGENTA
 |  |  |  |  | 11|  |  |  |  | 000-255| YELLOW
 |  |  | 6| 12| 12| 14| 21| 9| 16| CONTROL (active after 3 seconds)
000-005| NO FUNCTION
006-010| DIM CURVE: LINEAR
011-015| DIM CURVE: SQUARE
016-020| DIM CURVE: INVERSE SQUARE
021-025| DIM CURVE: S-CURVE
026-035| RESERVED
036-040| DIM BEHAVIOR: LED
041-045| DIM BEHAVIOR: HALOGEN
046-055| RESERVED
056-060| No DMX: Freeze MODE
061-065| No DMX: blackout delayed MODE
066-070| No DMX: blackout MODE
071-075| No DMX: Manual MODE
076-085| RESERVED
086-090| Display: BLINK ON
091-095| Display: BLINK OFF
096-160| RESERVED
106-110| FAN MODE = low / silent
111-115| FAN MODE = auto
116-120| FAN MODE = high / performance
121-130| RESERVED
131-135| LED PWM = 1200Hz
136-140| LED PWM = 2400Hz
141-145| LED PWM = 3600Hz
146-150| LED PWM = 7200Hz
151-155| LED PWM = 14400Hz
156-160| LED PWM = 20000Hz
161-165| LED PWM = 25000Hz
166-175| RESERVED
176-180| RED SHIFT OFF
181-185| RED SHIFT ON
186-195| RESERVED
196-200| LED CALIBRATION OFF
201-205| LED CALIBRATION ON
206-215| RESERVED
216-220| RECORD USER Color 1
221-225| RECORD USER Color 2
226-230| RECORD USER Color 3
231-235| RECORD USER Color 4
236-240| RECORD USER Color 5
241-255| RESERVED

COLOR PRESETS + LEE FILTER NAMES + CIE 1931 X/Y coordinates @ 3200K

0,35
Color preset 81| 166-167| Filter 285 (Three Quarter C.T. Orange)| 0,498| 0,42
Color preset 82| 168-169| Filter 328 (Follies Pink)| 0,532| 0,266
Color preset 83| 170-171| Filter 352 (Glacier Blue)| 0,217| 0,304
Color preset 84| 172-173| Filter 353 (Lighter Blue)| 0,25| 0,366
Color preset 85| 174-175| Filter 363 (Special Medium Blue)| 0,141| 0,095
Color preset 86| 176-177| Filter 507 (Madge)| 0,668| 0,331
Color preset 87| 178-179| Filter 706 (King False Lavender)| 0,271| 0,168
Color preset 88| 180-181| Filter 711 (Cold Blue)| 0,319| 0,318
Color preset 89| 182-183| Filter 724 (Ocean Blue)| 0,251| 0,339
Color preset 90| 184-185| Filter 728 (Steel Green)| 0,358| 0,402
Color preset 91| 186-187| Filter 747 (Easy White)| 0,497| 0,396
Color preset 92| 188-189| Filter 778 (Millennium Gold)| 0,628| 0,369
Color preset 93| 190-191| Filter 793 (Vanity Fair)| 0,591| 0,258
Color preset 94| 192-193| Filter 798 (Chrysalis Pink)| 0,302| 0,122

MAINTENANCE

• Make sure the area below the installation place is free from unwanted persons during servicing.

• Switch off the unit, unplug the mains cable and wait until the unit has been cooled down.
  During inspection the following points should be checked:

• All screws used for installing the device and any of its parts should be tightly fastened and may not be corroded.

• Housings, fixations and installations spots (ceiling, truss, suspensions) should be totally free from any deformation.

• When an optical lens is visibly damaged due to cracks or deep scratches, it must be replaced.

• The mains cables must be in impeccable condition and should be replaced immediately when even a small problem is detected.

• In order to protect the device from overheat the cooling fans (if any) and ventilation openings should be cleaned monthly.

• The interior of the device should be cleaned annually using a vacuum cleaner or air-jet.

• The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to optimize light output. Cleaning frequency depends on the environment in which the fixture operates: damp, smoky or particularly dirty surroundings can cause greater accumulation of dirt on the unit’s optics.

• Clean with a soft cloth using normal glass cleaning products.

• Always dry the parts carefully.
  Attention: We strongly recommend internal cleaning to be carried out by qualified personnel!

SPECIFICATIONS

This unit is radio-interference suppressed. This product meets the requirements of the current European and national guidelines. Conformity has been established and the relevant statements and documents have been deposited by the manufacturer.

Mains Input: AC 110 – 240V, 50/60Hz
Fuse: T5A / 250V (20x5mm)
Power consumption (max): 230 Watts
Power connections: PowerCON® compatible input / output
DMX connections: 3&5 pin-XLR male / female inputs + outputs
Lamp: RGBALC LED 200W
CRI: >93
Beam Angle: manual zoom 15° ~ 50°
Field Angle: 30° ~ 70°
IP-Rating: IP20
Operating Temperature: 0°C – 45°C
Size: See drawing
Weight: 8,2 kg

DIMENSIONS

LUX CHART (CCT: 3200K)

LUX CHART (FULL ON)

The information might be modified without prior notice
You can download the latest version of this user manual on our website: www .briteq-lighting.com

References

• Fresnel lens - Wikipedia
• Briteq - Home
• Briteq - Home

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>