BriTeQ BT-CHROMA 800 Indoor and Outdoor LED Projector User Manual

BriTeQ BT-CHROMA 800 Indoor and Outdoor LED Projector User Manual

OPERATION MANUAL

Thank you for buying this Briteq® product. To take full advantage of all possibilities and for your own safety, please read these operating instructions very carefully before you start using this unit.

FEATURES

• Powerful indoor / outdoor IP65 LED projector engineered for maximum flexibility in different
• Can be used for rental jobs, entertainment industry and fixed
• 40pcs 20W RGBL-leds assure very high light output with perfect color mixing and excellent white light!
• RGB, RGBL and HSI-color control, both 8 & 16 bit
• Extremely multifunctional cabling options:
  • RENTAL / ENTERTAINMENT applications: standard equipped with 3pin XLR and lockable IP65- Power connector in/outputs for easy daisy
  • FIXED installations: with an optional set called “ BT-CHROMA 800 – FIX install set” (POWER & DMX in/output modules with stainless-steel cable glands + 2 stainless-steel bolts for fixed TILT-positioning) the projector can very easily be transformed for permanent outdoor
• Standard equipped with 15° optics and magnetic aluminum filter frame with frost
• Different operation modes with 1, 2, 5 or 10 pixel combinations for nice special
• Full DMX-control with RDM-support: from easy 3CH to sophisticated 81CH control
• Built-in antenna and Wireless Solution ® G4 / G4S DMX-receiver (@ 4GHz) for easy setup and use.
• Standalone operation with static color & white presets, color fade and over 20 multi-pixel
• Different accessories optionally available to obtain perfect results:
  • Barndoor: adjust the beam easily on stage
  • Glare shield: static beam limiter hides the LEDs and eliminates unwanted stray light
  • Different beam shapers: 60° – 60°x 10° – 10°x 60° – 40°x 1° – 1°x 40° to get the perfect beam!
  • Empty magnetic filter frame: to easily install the different beam shapers
• Elegant, extruded aluminum housing finished with tempered glass
• Solid and multifunctional base:
  • Truss installation: easy truss mounting, using 1 or 2 optional OMEGA brackets
  • Fixed installation: easy and secure mounting on any surface, using standard anchor
• Optimal thermal management for long lifespan and easy maintenance
• Very silent operation, thanks to temperature controlled waterproof cooling
• Alphanumeric OLED-display and waterproof touch keys to select different options of the setup
• Adaptable lamp behavior thanks to seamless dimmer speed control.
• Four dimmer curves: linear, square, inverse square, S-curve
• In case of DMX failure, you can choose between blackout, freeze mode and automatic stand-alone
• Lock function to avoid unwanted altering of the
• Equipped with a special GORE® vent to prevent moisture and condensation inside the

BEFORE USE

• Before you start using this unit, please check if there’s no transportation damage. Should there be any, do not use the device and consult your dealer
• Important: This device left our factory in perfect condition and well packaged. It is absolutely necessary for the user to strictly follow the safety instructions and warnings in this user manual. Any damage caused by mishandling is not subject to warranty. The dealer will not accept responsibility for any resulting defects or problems caused by disregarding this user
• Keep this booklet in a safe place for future If you sell the fixture, be sure to add this user manual.

Check the contents:

Check that the packing contains the following items:

• BT-CHROMA800
• English operating instructions, other languages can be downloaded from our
• Magnetic filter frame with frost filter installed
• Small security cable for the filter frame
• Mains power cable

SAFETY INSTRUCTIONS:

| CAUTION: To reduce the risk of electric shock, do not remove the top cover. No user-serviceable parts inside. Refer servicing to qualified service personnel only.
---|---
| The lightning flash with arrowhead symbol within the equilateral triangle is intended to alert the use or the presence of un-insulated “dangerous voltage” within the product’s enclosure that may

be of sufficient magnitude to constitute a risk of electric shock.

| The exclamation point within the equilateral triangle is intended to alert the user to the presence of important operation and maintenance (servicing) instructions in the literature accompanying this appliance.
| This symbol means: indoor use only
| This symbol means: Read instructions
| This symbol determines: the minimum distance from lighted objects. The minimum distance between light-output and the illuminated surface must be more than 1 meters
| CAUTION: Do not stare at operating lamp. May be harmful to the eyes.
| | |

• To protect the environment, please try to recycle the packing material as much as possible.
• To avoid condensation to be formed inside, allow the unit to adapt to the surrounding temperatures when bringing it into a warm room after transport. Condense sometimes prevents the unit from working at full performance or may even cause
• Don’t place metal objects or spill liquid inside the unit. Electric shock or malfunction may result. If a foreign object enters the unit, immediately disconnect the mains
• Locate the fixture in a well ventilated spot, away from any flammable materials and/or liquids. The fixture must be fixed at least 50cm from surrounding
• Don’t cover any ventilation openings as this may result in
• Prevent use in dusty environments and clean the unit
• Keep the unit away from
• Inexperienced persons should not operate this
• Maximum safe ambient temperature is 40°C. Don’t use this unit at higher ambient
• Make sure the area below the installation place is free from unwanted persons during rigging, de-rigging and
• Allow the device about 10 minutes to cool down before to start
• Always unplug the unit when it is not used for a longer time or before to start
• The electrical installation should be carried out by qualified personal only, according to the regulations for electrical and mechanical safety in your country.
• Check that the available voltage is not higher than the one stated on the
• The power cord should always be in perfect condition. Switch the unit immediately off when the power cord is squashed or damaged. It must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a
• Never let the power-cord come into contact with other cables!
• This fixture must be earthed in order to comply with safety
• Don’t connect the unit to any dimmer
• Always use an appropriate and certified safety cable when installing the
• In order to prevent electric shock, do not open the There are no user serviceable parts inside.
• Never repair a fuse or bypass the fuse Always replace a damaged fuse with a fuse of the same type and electrical specifications!
• In the event of serious operating problems, stop using the fixture and contact your dealer
• The housing and the lenses must be replaced if they are visibly damaged.
• Please use the original packing when the device is to be
• Due to safety reasons it is prohibited to make unauthorized modifications to the

DESCRIPTION:

1. MAINS IN / OUTPUT: there are 2 versions:
   • Standard version (for stage/rental use): Equipped with connectors, connect the supplied mains cable here, you can daisy chain up to max. 3 units. Input and output are connected to each other without any fuse.
   • Fixed installation version: This is an optional module with waterproof cable glands. You can easily install a power cable with loose, stripped wire ends. (see electrical installation)
   Hint: Please check our website for special cable assemblies that contain both power (3×1.5mm² with
   Neutrik PowerCON® TRUE1) and balanced signal (XLR 3pin) in one cable. Different lengths are available: 1.3m, 3m, 5m and 10m, very convenient!

2. DMX IN/OUTPUTS: there are 2 versions:
   • Fixed installation version: This is an optional module with waterproof cable glands. You can easilyinstall a DMX-cable with loose, stripped wire ends. (see electrical installation)
   • Standard version (for stage/rental use): Equipped with connectors, connect good quality balanced signal cables with 3pin or 5pin XLR-connectors.

3. DISPLAY & BUTTONS: alphanumeric OLED-display and waterproof touch keys to select different options of the setup menu:
   • MENU-button: used to browse the different menu options or to exit a menu option.
   • ▼-button: used to go to the next menu option or to decrease a parameter value.
   • ▲-button: used to go to the previous menu option or to increase a parameter value.
   • ENTER-button: used to select a menu option or confirm a setting.

4. ANTENNA: antenna needed for wireless DMX-signal reception.

5.  COOLING FANS: due to the high power it is very important to make sure that the temperature-controlled fans and ventilation openings always remain free to maintain optimal cooling!

6. LOCKING TILT MECHANISM: serrated 180° mechanism with tilt angle display, there are 2 versions:
   • Standard version (for stage/rental use): a metal knob is used to adjust the tilt position easily, without using tools.
   • Fixed installation version: a stainless-steel hex socket bolt (included in the optional “BT-CHROMA 800 – FIX install set”) is used to assure that the tilt position cannot be altered easily.

7. HANDLE: to carry and adjust the projector easily.

8. FILTER FRAME: thanks to the use of strong magnets the frame can be exchanged easily, without the need for tools. Also check point 13! For fixed installation the frame can be fixed using screws to avoid theft.
   You can easily install different optional filters and beam shapers in the frame.

9. AIR PRESSURE VENT: for improved performance and service life, this special vent equalizes the pressure inside the projector while blocking water and preventing condense from being formed.

10. FIXING HOLES: these Ø13mm holes on both sides of the base are used to fix the projector firmly while used for permanent installation.

11. OMEGA BRACKET HOLES: for rental use, these holes with 106mm spacing are adapted to install 1 or 2 OMEGA brackets (small model).

12. SAFETY HOLE: used to attach a safety cable when the unit is rigged, see paragraph “overhead rigging”.

13.  FILTERFRAME SAFETY CABLE: A small safety cable is included to secure the filter frame when it is used with the magnetic holders.

Important: Never look directly into the light source! Don’t use the effect in the presence of persons suffering from epilepsy.

DESCRIPTION:

1. MAINS IN / OUTPUT: there are 2 versions:
   • Standard version (for stage/rental use): Equipped with connectors, connect the supplied mains cable here, you can daisy chain up to max. 3 units. Input and output are connected to each other without any fuse.
   • Fixed installation version: This is an optional module with waterproof cable You can easily install a power cable with loose, stripped wire ends. (see electrical installation)

Hint: Please check our website for special cable assemblies that contain both power (3×1.5mm² with Neutrik PowerCON ® TRUE1) and balanced signal (XLR 3pin) in one cable. Different lengths are available: 1.3m, 3m, 5m and 10m, very convenient!

2. DMX IN/OUTPUTS: there are 2 versions:
   • Fixed installation version: This is an optional module with waterproof cable You can easily install a DMX-cable with loose, stripped wire ends. (see electrical installation)
   • Standard version (for stage/rental use): Equipped with connectors, connect good quality balanced signal cables with 3pin or 5pin XLR-connectors.
3. DISPLAY & BUTTONS: alphanumeric OLED-display and waterproof touch keys to select different options of the setup menu:
   • MENU-button: used to browse the different menu options or to exit a menu option.
   • ▼-button: used to go to the next menu option or to decrease a parameter
   • ▲-button: used to go to the previous menu option or to increase a parameter
   • ENTER-button: used to select a menu option or confirm a
4. ANTENNA: antenna needed for wireless DMX-signal
5. COOLING FANS: due to the high power it is very important to make sure that the temperature-controlled fans and ventilation openings always remain free to maintain optimal cooling!
6. LOCKING TILT MECHANISM: serrated 180° mechanism with tilt angle display, there are 2 versions:
   • Standard version (for stage/rental use): a metal knob is used to adjust the tilt position easily, without using
   • Fixed installation version: a stainless-steel hex socket bolt (included in the optional “ BT-CHROMA 800 – FIX install set ”) is used to assure that the tilt position cannot be altered
7. HANDLE: to carry and adjust the projector easily.
8. FILTER FRAME: thanks to the use of strong magnets the frame can be exchanged easily, without the need for Also check point 13! For fixed installation the frame can be fixed using screws to avoid theft. You can easily install different optional filters and beam shapers in the frame.
9. AIR PRESSURE VENT: for improved performance and service life, this special vent equalizes the pressure inside the projector while blocking water and preventing condense from being
10. FIXING HOLES: these Ø13mm holes on both sides of the base are used to fix the projector firmly while used for permanent
11. OMEGA BRACKET HOLES: for rental use, these holes with 106mm spacing are adapted to install 1 or 2 OMEGA brackets (small model).
12. SAFETY HOLE: used to attach a safety cable when the unit is rigged, see paragraph “overhead rigging”.
13. FILTERFRAME SAFETY CABLE: A small safety cable is included to secure the filter frame when it is used with the magnetic holders.

OVERHEAD RIGGING

Important: The installation must be carried out by qualified service personal only. Improper installation can result in serious injuries and/or damage to property. Overhead rigging requires extensive experience! Working load limits should be respected, certified installation materials should be used, the installed device should be inspected regularly for safety.

• Make sure the area below the installation place is free from unwanted persons during rigging, de-rigging and
• Locate the fixture in a well-ventilated spot, far away from any flammable materials and/or The fixture must be fixed at least 50cm from surrounding walls.
• The device should be installed out of reach of people and outside areas where persons may walk by or be
• Before rigging make sure that the installation area can hold a minimum point load of 10times the device’s weight.
• Always use a certified safety cable that can hold 12times the weight of the device when installing the unit. This secondary safety attachment should be installed in a way that no part of the installation can drop more than 20cm if the main attachment
• The device should be well fixed; a free-swinging mounting is dangerous and may not be considered!
• Don’t cover any ventilation openings as this may result in
• The operator has to make sure that the safety-relating and machine-technical installations are approved by an expert before using them for the first time. The installations should be inspected every year by a skilled person to be sure that safety is still

SETUP MENU:

• Press the MENU button to ENTER the setup
• Press the ▼/▲ buttons to browse the menu until the required function shows
• Select the function with the ENTER button.
• Use ▼/▲ buttons to change the
• Press the ENTER button to confirm the selected

DMX FUNCTIONS menu

DMX ADDRESS

Used to set the desired DMX-address.

• Press the ▼/▲ buttons to browse the menu until the required function shows
• Press the ENTER button: the values can be changed
• Use ▼/▲ buttons to select the desired DMX512 The last occupied DMX-address is also shown: makes it easier to set the address of the next unit in the chain.
• Once the correct address shows on the display, press the ENTER button to save it.

Note: on RDM-compatible controllers this option can also be remotely set.

CHANNEL MODE

Used to set the desired channel mode.

• Press the ▼/▲ buttons to browse the menu until the required function shows

• Press the ENTER button: the values can be changed

• Use ▼/▲ buttons to select the desired mode:

  • RGB 8bit (3CH) 3 colors set in 8bit resolution, no lime color, no master
  • RGB 16bit (6CH) 3 colors set in 16bit resolution, no lime color, no master
  • RGBL 8bit (3CH) 4 colors set in 8bit resolution, no master dimmer.
  • RGBL 16bit (6CH) 4 colors set in 16bit resolution, no master
  • HSI 8bit (3CH) 8 bit HSI (Hue, Saturation, Intensity) color model (lime color not used)
  • HSI 16bit (6CH) 16 bit HSI (Hue, Saturation, Intensity) color model (lime color not used)
  • RGBL D+STR (6CH) 4 colors set in 8bit resolution + master dimmer and
  • RGBL FX (11CH) 4 colors set in 8bit resolution + built-in pixel effects (multifunctional mode).
  • RGBL 2px 8bit 4 colors set in 8bit resolution + 2-pixel control
  • RGBL 5px 8bit 4 colors set in 8bit resolution + 5-pixel control
  • RGBL 10px 8bit 4 colors set in 8bit resolution + 10-pixel control
  • RGBL 10px 16bit 4 colors set in 16bit resolution + 10-pixel control

• Once the correct option shows on the display, press the ENTER button to save it. Remark: on RDM-compatible controllers this option can also be remotely set.

__

SETUP MENU

DMX functions

| DMX Address| XXX – YYY
CHANNEL Mode| ****
W-DMX ON/OFF| ON /OFF
W-DMX Unlink| YES/NO
__

__

__

__

__

__

__

__

SETUP MENU

Functions

| __

NO DMX Mode

| Blackout
Freeze
Stand-Alone
Display FLASH| on/off
Display AUTOLOCK| on/off/DMX-controlled
Temp Units: C/F| °C / F
Pixel Order| Standard (0°)
Flipped (180°)
Dimmer Speed| XXX (Y.Y s)
__

Dimmer Curve

| Linear
Square
Inverse Square
S-Curve
__

Fan Speed

| Auto
Low
High
__

__

__

__

__

__

__

__

__

__

__

SETUP MENU

Stand-Alone

| __

Working Mode

| SLAVE Mode
MASTER: Full on
MASTER: Program

01→22

Program Speed| 000→255
Afterglow| 000→255
Master Dimmer| 000→255
__

__

__

__

__

__

__

Color Effects

| Set Custom Color
Red
Orange
Yellow
Green
Cyan
Blue
Purple
WHITE 3000K
WHITE 4000K
WHITE 5600K
Color Fade 01
↓
Color Fade 99
SETUP MENU

Default Settings

| Factory Reset| LOAD ?
USER Defaults| LOAD / SAVE ?
__

__

SETUP MENU

Information

| DMX CH. Values|
LED Temperature| xxx °C
TOTAL Usage Time| xxxx Hrs
JOB Usage Time| xxxx Hrs
Error Messages| **
Firmware Version| V x.xx

W-DMX ON/OFF

Used to switch the internal wireless DMX receiver on/off.
• Press the ▼/▲ buttons to browse the menu until the required function shows up.
• Use ▼/▲ buttons to toggle between ON & OFF.

W-DMX Unlink

The projector can only be linked to the wireless DMX transmitter when no wireless links already exist. This function is used to break (unlink) any wireless links that might still exist.

• Press the ▼/▲ buttons to browse the menu until the required function shows
• Use ▼/▲ buttons to toggle between YES &

FUNCTIONS menu

NO DMX Mode

Used to set how the projector reacts when the DMX-signal suddenly disappears.

• Press the ▼/▲ buttons to browse the menu until the required function shows
• Press the ENTER button: the values can be changed
• Use ▼/▲ buttons to select the desired mode:
  • BLACKOUT: output turns black while no DMX is
  • FREEZE: output based on the last valid DMX-signal is kept on the
  • STAND-ALONE: the internally selected “stand-alone” mode starts
• Once the correct option shows on the display, press the ENTER button to save

Note: as soon as the input detects a DMX-signal, blackout or freeze mode will be cancelled.

Display FLASH

Used to select if the display should flash or not while no DMX-signal is detected.

• Press the ▼/▲ buttons to browse the menu until the required function shows
• Use ▼/▲ buttons to toggle between ON &

DISPLAY AUTOLOCK

Used to lock the setup menu against unwanted altering of the settings.

• Press the ▼/▲ buttons to browse the menu until the required function shows
• Press the ENTER button: the values can be changed
• Use ▼/▲ buttons to select the desired mode:
  • OFF The setup menu can be used at any time.
  • ON After a short time the setup menu locks automatically, the display shows **LOCKED ***. Unlock the display by pressing the buttons in this order: ▲, ▼, ▲, ▼, ENTER.
  • DMX-controlled: this mode is only for use in fixed installations. You can disable/enable both the buttons and display using a specific DMX-command: for more information, see chapter “ELECTRICAL INSTALLATION + USE” → subheading “Fixed Installations”
• Once the correct option shows on the display, press the ENTER button to save it.

Temp Units C/F

Used to select if the LED-temperature is shown in degrees Celsius °C or Fahrenheit F.

• Press the ▼/▲ buttons to browse the menu until the required function shows
• Press the ENTER button: the values can be changed
• Use ▼/▲ buttons to select the desired mode:
  • °C: temperature shown in degrees
  • F: temperature shown in
• Once the correct option shows on the display, press the ENTER button to save

Pixel Order

To keep uniformity, you can flip the pixel order when some projectors are mounted normally and others upside-down (suspended).

• Press the ▼/▲ buttons to browse the menu until the required function shows
• Press the ENTER button: the values can be changed
• Use ▼/▲ buttons to select the desired mode:
  

DIMMER SPEED

Used to set the speed (smoothness) of the dimmer continuously.

• Press the ▼/▲ buttons to browse the menu until the required function shows up.

• Press the ENTER button: the values can be changed

• Use ▲/▼ buttons to select the desired speed:

  • 000 (0ms): The projector follows the instructions instantly, no delay (also called LED behavior)

• 255 (2000ms): The projector imitates the behavior of a halogen lamp (slower reaction time).

• Once the desired value shows on the display, press the ENTER button to

Remark: The default value (100 or 440ms) is the most realistic value to imitate “halogen lamp” behavior. At the same time the light output will be instantaneous while pushing a flash button on your DMX-controller

DIMMER CURVE

Used to set the dimmer curve of the master dimmer.

• Press the ▼/▲ buttons to browse the menu until the required function shows
• Press the ENTER button: the values can be changed
• Use ▼/▲ buttons to selected the desired curve:

FAN SPEED

Used to adapt the speed of the cooling fans.

• Press the ▼/▲ buttons to browse the menu until the required function shows up.
• Press the ENTER button: the values can be changed
• Use ▲/▼ buttons to select the desired speed:
• AUTO: The fan speed is temperature controlled for the best possible balance between performance and LED temperature (default mode).
• LOW: The fan speed is temperature controlled for the best possible balance between performance and low noise. The fan speed is limited so the output will be reduced when the temperature is high.
• HIGH: The fan speed is temperature controlled for the best possible performance. The fan speed is higher so it will produce more fan noises.
• Once the desired value shows on the display, press the ENTER button to confirm.

STAND-ALONE menu

**WORKING MODE**

Used to select the desired working mode while the projector is in stand- alone mode

• Press the ▼/▲ buttons to browse the menu until the required function shows
• Press the ENTER button: the values can be changed
• Use ▼/▲ buttons to select the desired mode:
  • SLAVE Mode: The projector copies the light output of the master (working in stand-alone mode)
  • MASTER: Full on: The projector works in MASTER Mode with no running program, you can choose a color with the Color Effects option.
  • MASTER: Program 01-22: The projector works in MASTER Mode, you can select one of the internal pixel programs (also select program speed)
• Once the desired value shows on the display, press the ENTER button to

PROGRAM SPEED

Used to select the desired speed of the selected pixel program

• Press the ▼/▲ buttons to browse the menu until the required function shows up.
• Press the ENTER button: the values can be changed
• Use ▼/▲ buttons to select the desired speed: 000 (slow) → 255 (fast)
• Once the desired value shows on the display, press the ENTER button to

Remark: the program speed depends on the amount of Afterglow: reduce the afterglow value if the program speed is not high enough.

AFTERGLOW

Used to select the desired “afterglow” effect while pixel programs are running.

• Press the ▼/▲ buttons to browse the menu until the required function shows up.
• Press the ENTER button: the values can be changed
• Use ▼/▲ buttons to select the desired speed: 000 (no afterglow) → 255 (long afterglow)
• Once the desired value shows on the display, press the ENTER button to

Remark: the program speed depends on the amount of Afterglow: reduce the afterglow value if the program speed is not high enough.

MASTER DIM

Used to set the master dimmer while used as (stand-alone) master.

• Press the ▼/▲ buttons to browse the menu until the required function shows up.
• Press the ENTER button: the values can be changed
• Use ▼/▲ buttons to select the desired level for the master
• Once you have the desired level, press the ENTER button to save

Note: the setting of this option has NO effect while the projector is used as SLAVE or in DMX-mode.

COLOR EFFECTS

Used to set the desired color while used as master: 10 preset colors + 1 custom color + Color fades.

• Press the ▼/▲ buttons to browse the menu until the required function shows up.
• Press the ENTER button: the values can be changed
• Use ▼/▲ buttons to selected the desired color:

· RED

• ORANGE

· YELLOW

• GREEN

·CYAN

• BLUE

· PURPLE

• WHITE 3000K (pleasant warm white light for all kinds of situations)
• WHITE 4000K (the preferred color temperature for exhibition booths)
• WHITE 5600K (preferred daylight color temperature, good for camera work)
• SET CUSTOM COLOR is a custom color that can be set by the Follow these steps:
• Press the ENTER button: the display shows the value (000-255) for (change with ▼/▲ buttons)
• Press the ENTER button: the display shows the value (000-255) for (change with ▼/▲ buttons)
• Press the ENTER button: the display shows the value (000-255) for BLUE. (change with ▼/▲ buttons)
• Press the ENTER button: the display shows the value (000-255) for (change with ▼/▲ buttons)
• Repeat these steps until you have the desired The settings will be automatically saved.

DEFAULT SETTINGS → FACTORY RESET + USER DEFAULTS

This is your emergency exit if you really messed up the settings: just return to factory settings. Also 2 user settings can be saved/loaded.

• Press the ▼/▲ buttons to browse the menu until the required function shows
• Press the ENTER button: the values can be changed
• Use ▼/▲ buttons to selected the desired settings:

·    Factory Reset

• USER Defaults

• Press the ENTER button:

  • Factory Reset was selected: the display shows LOAD?
  • Press the ENTER button: the display shows CONFIRM
  • Use ▼/▲ buttons to select YES / NO
  • Press the ENTER button to
  • USER Defaults was selected: the display shows LOAD?
  • Use ▼/▲ buttons to select LOAD / SAVE
  • Press the ENTER button to confirm: the display shows USER1 / USER2
  • Use ▼/▲ buttons to select YES / NO

• Press the ENTER button to

  • SAVE was selected: the current settings of the setup menu are saved to
  • LOAD was selected: the previously saved settings are

Default values:

PARAMETER name| FACTORY defaults| USER1 defaults| USER2 defaults
---|---|---|---
CHANNEL Mode| RGBL + FX (11CH)| Current setting in the menu| Current setting in the menu
W-DMX ON/OFF| ON| Current setting in the menu| Current setting in the menu
NO DMX Mode| Freeze| Current setting in the menu| Current setting in the menu
Display FLASH| ON| Current setting in the menu| Current setting in the menu
Display AUTOLOCK| OFF| Current setting in the menu| Current setting in the menu
Pixel Order| Standard 0°| Current setting in the menu| Current setting in the menu
DIMMER Speed| 100| Current setting in the menu| Current setting in the menu
DIMMER Curve| Square| Current setting in the menu| Current setting in the menu
FAN Speed| AUTO| Current setting in the menu| Current setting in the menu
Working Mode| All Pixels ON| Current setting in the menu| Current setting in the menu
Program Speed| 128| Current setting in the menu| Current setting in the menu
Master Dimmer| 255| Current setting in the menu| Current setting in the menu
Color Effects| Color Fade 75| Current setting in the menu| Current setting in the menu
Custom Color RGBL| NO factory default| Current setting in the menu| Current setting in the menu
Afterglow| 80| Current setting in the menu| Current setting in the menu
LED Calibration| NO factory default| LED calibrations are saved| LED calibrations are saved
Temp Units C/F| Celsius| Current setting in the menu| Current setting in the menu

INFORMATION menu

DMX CH. Values

Used to monitor the incoming DMX-signals, handy for fault debugging.

• Press the ▼/▲ buttons to browse the menu until the required function shows
• Press the ENTER button: you can monitor the incoming DMX-signal, functions and values ar

LED Temperature

Shows the current LED Temperature.

• Press the ▼/▲ buttons to browse the menu until the required function shows
• Press the ENTER button: the current LED temperature is

TOTAL Usage Time

Shows the Total time the projector was switched on, starting from the 1 st day it was used.

• Press the ▼/▲ buttons to browse the menu until the required function shows
• Press the ENTER button: the TOTAL usage time is shown, this value cannot be

JOB Usage Time

Shows the Total time the projector was switched on since the last JOB Time reset. Can be used to check how long a customer used the projector on a job.

• Press the ▼/▲ buttons to browse the menu until the required function shows
• Press the ENTER button: the job usage time is shown, this value can be reset in a hidden

ERROR Messages

Shows eventual ERROR messages if they exist.

• Press the ▼/▲ buttons to browse the menu until the required function shows
• Press the ENTER button: under normal conditions the display shows “None”

Firmware Version

Shows actual firmware version information.

• Press the ▼/▲ buttons to browse the menu until the required function shows
• Press the ENTER button: the current firmware version of the 1U processor is
• Press the ▼/▲ buttons to browse the firmware versions of the other

Note: The firmware of this unit can be upgraded using our special “Firmware Updater 2+” (separately available from Briteq). More information about this can be found in the user manual of the firmware updater or our website: _ _https://briteq-lighting.com/firmware-updater-2-plus__

HIDDEN menu

In the hidden menu you can reset the JOB Usage Time counter and adjust the white balance. To access the hidden menu, simply press the ENTER-button for about 3 seconds.
Press the MENU-button to leave the hidden menu again.
Reset JOB Usage Time
Used to reset the timer that shows how long the unit was used on the last job.

• Press the ▼/▲ buttons to browse the menu until the required function shows
• Press the ENTER button: the display shows NO
• Use ▼/▲ buttons to toggle between YES &
• Press the ENTER button to

LED Calibration

Used to set the white balance or to perfectly match the colors of several projectors or after changing one of the LEDs of the projector.

• Press the ▼/▲ buttons to browse the menu until the required function shows
• Press the ENTER button: the display shows the selected color for LEDs 1 to (change with ▼/▲ buttons)
• Press the ENTER button: the display shows the value (050-255) for the selected color /
• Use ▼/▲ buttons to adapt the value between 050 and 255 and confirm with ENTER
• Repeat these steps until you have the desired The settings will be automatically saved.

There’s also a shortcut to reset all calibration values back to 255:

• Press the ▼/▲ buttons until the display shows: ALL LEDs = 255
• Press the ENTER button: the display shows NO
• Use ▼/▲ buttons to toggle between YES &
• Press the ENTER button to

Note: Use this function with caution as it overwrites all manual calibrations, no recovery possible.

ELECTRICAL INSTALLATION + USE

Important: The electrical installation should be carried out by

qualified personal only, according to the regulations for electrical and mechanical safety in your country.

**Electrical installation:
FIXED installations**

Optional DMX and POWER in/output modules are available with stainless-steel cable glands for fixed installation: can be purchased separately as “ BT- CHROMA 800 – FIX install set ”

The set consists of 2 modules that can be easily installed instead of the standard connectors and 2 stainless- steel hex socket bolts to secure the TILT-mechanism in the right position. (see points n° 1+ 2 in the description)

Optional parts

BT-CHROMA 800 – FIX install set (order code: B05546)

Set with waterproof Power & DMX in/output glands

BT-CHROMA 800 – Barndoor (order code: B05547)

8-leaf barndoor for stage appl

__

BT-CHROMA 800 – Glare Shield (order code: B05548)

Fixed glare shield for fixed installations

__

BT-CHROMA 800 – Filter frame (order code: B05549)

Empty magnetic filter frame to install beam shaper filters

__

__ BT-CHROMA 800 – Anti Glare Frame (order code: B05559)

Fixed anti-glare frame for fixed installations

Different BEAM SHAPERS

BT-CHROMA 800 – 60×10 beam (order code: B05550) 60°x10° beam shaper (without frame) BT-CHROMA 800 – 10×60 beam         (order code: B05551) 10°x60° beam shaper (without frame) BT-CHROMA 800 – 40×1 beam (order code: B05552) 40°x1° beam shaper (without frame) BT-CHROMA 800 – 1×40 beam (order code: B05553) 1°x40° beam shaper (without frame)
BT-CHROMA 800 – 60° beam (order code: B05554) 60°x60° beam shaper (without frame)

Read More About This Manual & Download PDF:

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>