ingenico Move/2600 Payment Terminal User Guide

: June 12, 2024
: ingenico

Table of Contents

ingenico Move/2600 Payment Terminal
Product Information
Introduction
Presentation
Use of the terminal
Installation
Troubleshooting
FCC STATEMENT
More Information
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

ingenico Move/2600 Payment Terminal

ingenico-Move-2600-Payment-Terminal-product

Product Information

The Move/2600 is a terminal unit designed for various applications. It comes equipped with a 2.4″ LCD display, a backlight keyboard with large keys, a contactless card reader, an easy loading printer, a smart card reader, and a magnetic stripe reader. The terminal weighs 254g and has dimensions of 167x76x56 mm (L x W x H). It operates on an electrical mains network with a power supply unit (PSU) that supports 100 – 240VAC / 50-60 Hz or 50/60Hz. The terminal can be connected to a USB-C connector for the PSU.

Keyboard Details and Functionality

The keyboard of the Move/2600 terminal has navigation keys, a cancel key, a clear key, a validation key, and a feed paper key.
Some keys may have additional functions depending on the applications installed on the terminal.

Introduction

We hope that you will be fully satisfied with your new terminal Move/2600. Please select by yourself in this documentation items related to your model. Read this guide to understand and make the best use of your terminal. It presents you the necessary information about use, installation, maintenance, safety and security recommendations.

WARRANTY / SECURITY

Use only the power supply included with the product to ensure best performance and safety. Maintenance should only be provided by Ingenico authorized technician.
Failure to comply with these instructions will void the manufacturer’s responsibility.
This symbol indicates an important Warning.
This symbol indicates a piece of advice.

Presentation

Content of the box

Move/2600 terminal unit equipped with a paper roll
A battery pack
Power Supply Unit (PSU)

_ ADVICE: _Keep the packaging. It must be re-used whenever the terminal is shipped.

Overview of the Move/2600

ingenico-Move-2600-Payment-Terminal-fig-5

The compartment where are located:

ingenico-Move-2600-Payment-Terminal-fig-6

The battery pack
The SIM/SAM slots

Weight (without paper roll nor battery): 254g
Dimensions (L x w x h): 167x76x 56 mm
Electrical mains network: 100 – 240VAC / 50-60 Hz or 50/60Hz – Class II equipment
Connections on terminal: USB-C connector for PSU

Keyboard details and functionality

ingenico-Move-2600-Payment-Terminal-fig-7

Some keys can have other functions according to the applications that are in the terminal.

Use of the terminal

Before using the terminal, always check if the paper roll is present and if battery is connected. Without battery pack connected, printer and 4G connectivity won’t be available.

Switching off the terminal

If the battery is empty and the terminal in use is removed from its base, the terminal automatically shuts off.
It may also be switch by pressing simultaneously and (yellow key) for one second.
In order to restart the terminal, press on the keyboard.

Reading card

Magnetic stripe card

ingenico-Move-2600-Payment-Terminal-fig-11

The card can be read either from left to right or from right to left, with the stripe on top of the terminal (stripe can be seen by user).
Use a regular movement to ensure a reliable card reading.

Smart card

Insert the card horizontally with the chip facing upwards and leave in position throughout the transaction.

Contactless (Cless)

Bring the card firmly up to the active zone. Keep the card close to the reader during the transaction.
The 4 virtual LEDs are displayed during the transaction.

The terminal behavior for the cardholder may depend on:

The terminal environment
Local usage (language,…)

Installation

Recommendations

Location of the Move/2600

Place the product on flat surface near an electric socket and according to the options close to an Ethernet socket.
The terminal should be placed far from any very hot zones, protected from vibrations, dust, damp and electromagnetic radiation (computer screen, anti-theft barrier etc.).

Operating conditions

Ambient temperature: from +0°C to +50°C
Max relative humidity: 85% at +40°C

Battery charging conditions

Ambient temperature: from +0°C to +45°C

Storage conditions

Ambient temperature: from -20°C to +55°C
Max relative humidity: 85% at +55°C

Product connections

Terminal USB

A USB type C connector is available behind the battery door of Move/2600.
This connector is used to connect PSU or USB type C to USB slave type A cable or USB type C to USB Host connector.
This connector can also be used for SW loading.

Opening trap door

CAUTION: Switch off the terminal before opening the trapdoor.

Turn the terminal and unclip the trapdoor by pushing on the clip with as shown with the arrows on the picture

SAMs & SIMs

The connector modules security SAM/SIM is located inside the terminal, in a closed compartment. Please, switch off the Move/2600 prior inserting the SIM/SAM.

SAMs and SIMs are identified by the engraved marks on the lower housing
When introducing a SAM/SIM in its slot, be sure to put the cut corner as indicated on the engraved marks
3 factory options: 1SIM/2SAMs, 2SIMs/1SAM or 3 SAMs (always 3 SAMs when product doesn’t embed 4G option)

Cable connection

To use Magic Box connectivity, the use of cable is necessary and is included in your product box in option.

Connect the cable and make it follow the cable way as shown on following picture. Take care to place it behind the plastic wall.
Plug can be inserted in both directions.

Battery

Mains characteristics

Characteristics: Li-Ion 2250mAh
Charge (power supply 1A): 50% of capacity in 1.5h (1A)
- Full capacity in 4h (1A)
Battery life: 450 transactions in 4G with fully charged battery, printing and backlit activated
- Can remain powered ON up to 150 hours with connected 4G link and terminal in sleeping state starting with fully charged battery and without energy consumption related to backlit or radio link

Installing the battery

_ WARNING: _Check that the terminal is not connected to the main electric network before installing or removing the battery.

Turn your terminal and unclip the battery trapdoor by pushing on the button as shown on the picture
Disengage the trapdoor
Take the battery pack included in the box
Locate the battery pack connector beside the battery compartment
Plug the battery pack connector according to the connector locating system and (as shown on picture). Verify that it locks.
Place the battery pack in its compartment.
Close the battery compartment trapdoor.

Charging the battery

When does the battery need to be charged?
- On initial start-up, charge the battery for 16 hours under the environmental conditions stated above
- When used with a terminal power supply: connect the power supply to Move/2600 power connector
How does the battery need to be charged?
- The environment in which the charge takes place influences battery lifetime and autonomy (number of transactions)
- The optimal conditions are as follows:
  - Charging away from any external heat source (radiator, sun, enclosed area…)
  - The optimal temperature is between +15°C and +25°C
How can the battery be charged?
- Using the terminal power supply
- Connect the terminal power supply unit to the terminal USB type C connector located above the battery door
- Connect the power supply unit to the power supply mains networks
- Check to see if the battery symbol is flashing or moving (=battery charging)

Changing the battery

Warning

It is imperative to use the battery authorized by Ingenico.
There is danger of explosion if the battery used is not approved by Ingenico.

Disconnect the power supply unit
Turn product off by pressing simultaneously ( dot key) and (yellow key) for one second .
Remove the battery door (See chapter “Installation”).
Lift the battery and remove it from its compartment.
Carefully disconnect battery by pulling on connector. Avoid pulling wires to do not damage the battery.
Connect and install the new battery by following the instructions in chapter “Installation”.
In order to preserve the environment, dispose used battery in compliance with current country recycling legislation.

Paper roll

Main characteristics of Ingenico roll

Paper roll characteristics: Precisions
Color: White
Width: 58 mm
Diameter: 40 mm
Length: About 18 meters

The thermal paper can be deteriorated by poor storage conditions, so we recommend you to avoid:

Storage in hot wet places (near air-conditioner, humidity higher than 85%)
Exposure to sunlight or ultraviolet for long periods
Contact with organic solvents (solvent type adhesive
Direct contact with materials containing plasticizers (PVC transparent folders or envelopes)
Direct contact with “diazo” papers
Direct contact with water
Rubbing or pressing the paper too strongly

_ WARNING: _For best product performance, only use heat sensitized paper approved by Ingenico.

Installing paper roll

WARNING

Switch off the terminal prior to installing a paper roll.
Use only paper approved by Ingenico. The use of nonapproved paper is likely to damage the printer of your terminal.

ingenico-Move-2600-Payment-Terminal-fig-21

Open the paper compartment by lifting the catch located at the rear and under the terminal and pull the cover.
Insert the paper roll in the compartment following the directions shown on the below picture.
Pull the paper up to the top of the terminal.
Maintain the paper and close the lid.
Press simultaneously on both upper corners of the paper flap until it clips into position.

ADVICE: If you insert a new paper roll, tear off the first length (one complete turn to avoid printing on adhesive tape footprint).

Troubleshooting

The terminal does not turn on

Check the battery (is it discharged, is it connected?). A full discharged battery can take long charging time to recover.
Connect terminal to terminal power supply or put it on powered base.

Cards are not read

Check that the magnetic card is swiped correctly (with magnetic band on terminal side).
Swipe again the card with the magnetic stripe movement constant and rapid
Verify that the magnetic strip is not damaged, grooved or cracked
Make sure you have inserted correctly the smart card into the smart card reader and removed the card only after the transaction is performed.

The ticket is not printed

Check the presence and proper positioning of the paper roll.
Possibly adjust the paper roll following the instructions in this manual (section 0 “Installing the paper roll”)
Check the type of paper used (thermal paper must be used)
Verify thermal paper sensitive side.
Check battery pack is correctly connected.

FCC STATEMENT

You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on, the user is encouraged to try to correct interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules and Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

This device may not cause harmful interference.
This device must accept any interference received, including interference that may cause undesired operation.

Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada.
To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
The device for operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems. In addition, high-power radars are allocated as primary users (i.e. priority users) of the bands 5250–5350 MHz and 5650–5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices.

SAR Maximum value