Crytec CRC200X Wood Chippe User Manual
- August 26, 2024
- Crytec
Table of Contents
- Crytec CRC200X Wood Chippe
- SAFETY AND OPERATION INSTRUCTIONS
- PART I: General Safety Rules
- Before using the wood chipper
- When using the wood chipper
- Protecting Yourself and Those Around You
- Safety for Children and Pets
- Safety with Gasoline – Powered Machines
- General Safety
- A Note to All Users
- PART II: Familiar with the Wood Chipper
- TECHNICAL SPECIFICATIONS
- PART III: Operating the Wood Chipper
- Assemble the Wood Chipper
- Starting
- Stopping
- Disassemble the discharge
- PART IV: Maintaining the Wood Chipper
- PART V: Troubleshooting and Parts List
- Troubleshooting Table
- Explosion View and parts list
- Specifications:
- FAQ:
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Crytec CRC200X Wood Chippe
USER MANUAL
SAFETY AND OPERATION INSTRUCTIONS
IMPORTANT : Read safety rules and instructions carefully before operating equipment.
WARNING
This indicates a hazardous situation, which, if not avoided, could result in death or serious injury.
CAUTION
This indicates a hazardous situation, which, if not avoided, could result in minor or moderate injury.
NOTICE
This information is important in proper using of your machine. Failure to
follow this instruction could result in damage to your machine or property.
Additional Information and Potential Changes
We reserve the right to discontinue, change, and improve its products at any time without notice or obligation to the purchaser. The descriptions and specifications contained in this manual were in effect at printing. Equipment described within this manual may be optional.
Some illustrations may not be applicable to your machine.
PART I: General Safety Rules
Safety Labels Found on Your Unit
WARNING
Read this Safety & Operating Instructions manual before you use the Wood
Chipper.
Become familiar with the operation and service recommendations to ensure the
best performance of your machine.
Propose
CAUTION
This machine is designed solely to chip wood and must not be used for any
other purpose.
It should only be used by trained operators who are familiar with the content
of this manual.
It is potentially hazardous to fit or use any parts other than your dealer
parts. The company disclaims all liability for the consequences of such use,
which in addition voids the machine warranty.
Before using the wood chipper
NOTICE
A. Operators must be fully trained before using this machine.
B.User Manual is read and understood.
C. Machine is positioned on level ground, all guards are fitted and in good
condition.
D. Blades are in good condition and secure. All blades are sharpened or
replaced in sets.
E.All fasteners are checked for tightness.
F.Only WOODEN materials free of nails etc. are fed into the machine.
G. Emergency stop wire is rightly connected and the switch is functional.
H. Fire extinguisher is available on site.
When using the wood chipper
NOTICE
A. Always feed from the side.
B. It is better to have a second trained operator within easy reach of the
machine.
C. Maintain strict discipline at all times and service machine at specified
periods.
D. Note direction of discharge chute and if necessary note the wind direction
to prevent
debris from being blown into highway or where it could affect members of the
public.
E. DO NOT put any part of your body into the in-feed chute while the machine
is running.
F. DO NOT operate the machine whilst under the influence of alcohol or drugs.
G. DO NOT operate inside a building or confined space or Climb on the in-feed
chute.
Protecting Yourself and Those Around You
WARNING
This is a high-powered machine, with moving parts operating with high energy. You must operate the machine safely. Unsafe operation can create a number of hazards for you, as well as anyone else in the nearby area. Always take the following precautions when using this machine:
A. Keep in mind that the operator or user is responsible for accidents or
hazards occurring to other people, their property, and themselves.
B. Always wear protective goggles or safety glasses with side shields while
using the Wood Chipper to protect your eyes from possible thrown debris.
C. Avoid wearing loose clothing or jewelry, which can catch on moving parts.
D. We recommend wearing gloves while using the Wood Chipper. Be sure your
gloves fit properly and do not have loose cuffs or drawstrings.
E. Wear shoes with non-slip treads when using your Wood Chipper. If you have
safety shoes, we recommend wearing them. Do not use the machine while barefoot
or wearing open sandals.
F. Wear long pants while operating the Wood Chipper.
G. Keep bystanders at least 50 feet away from your work area at all times.
Stop the engine when another person or pet approaches.
Safety for Children and Pets
WARNING
Tragic accidents can occur if the operator is not alert to the presence of
children and pets.
Children are often attracted to the machine and the chipping activity. Never
assume that children will remain where you last saw them. Always follow these
precautions:
A. Keep children and pets at least 50 feet from the working area and ensure
they are under the watchful care of a responsible adult.
B. Be alert and turn the machine off if children or pets enter the work area.
C. Never allow children to operate the Wood Chipper.
Safety with Gasoline – Powered Machines
WARNING
Gasoline is a highly flammable liquid. Gasoline also gives off flammable vapor that can be easily ignited and cause a fire or explosion. Never overlook the hazards of gasoline. Always follow these precautions:
A. Never run the engine in an enclosed area or without proper ventilation as
the exhaust from the engine contains carbon monoxide, which is an odorless,
tasteless, and a deadly poisonous gas.
B. Store all fuel and oil in containers specifically designed and approved for
this purpose and keep away from heat and open flame, and out of the reach of
children.
C. Replace rubber fuel lines and grommets when worn or damaged and after 5
years of use.
D. Fill the gasoline tank outdoors with the engine off and allow the engine to
cool completely. Don’t handle gasoline if you or anyone nearby is smoking, or
if you’re near anything that could cause it to ignite or explode. Reinstall
the fuel tank cap and fuel container cap securely.
E. If you spill gasoline, do not attempt to start the engine. Move the machine
away from the area of the spill and avoid creating any source of ignition
until the gas vapors have dissipated. Wipe up any spilled fuel to prevent a
fire hazard and properly dispose of the waste.
F. Allow the engine to cool completely before storing in any enclosure. Never
store a machine that has gas in the tank, or a fuel container, near an open
flame or spark such as a water heater, space heater, clothes dryer or furnace.
G. Never make adjustments or repairs with the engine running. Shut down the
engine, disconnect the spark plug wire, keeping it away from the spark plug to
prevent accidental starting, wait 5 minutes before making adjustments or
repairs.
H. Never tamper with the engine’s governor setting. The governor controls the
maximum safe operation speed and protects the engine. Over-speeding the engine
is dangerous and will cause damage to the engine and to the other moving parts
of the machine. If required, see your authorized dealer for engine governor
adjustments.
I. Keep combustible substances away from the engine when it is hot.
J. Never cover the machine while the muffler is still hot.
K. Do not operate the engine with the air cleaner or the carburetor air intake
cover removed. Removal of such parts could create a fire hazard. Do not use
flammable solutions to clean the air filter.
L. The muffler and engine become very hot and can cause a severe burn; do not
touch.
M. Never refuel the machine indoors
General Safety
WARNING
Operating this Wood Chipper safely is necessary to prevent or minimize the risk of death or serious injury. Unsafe operation can create a number of hazards for you. Always take the following precautions when operating:
A. Your Wood Chipper is a powerful tool, not a plaything. Exercise extreme
caution at all times. The machine is designed to Chip Woods. Do not use it for
any other purpose.
B. Know how to stop the Wood Chipper quickly.
C. Never operate your unit on a slippery, wet, muddy, or icy surface. Exercise
caution to avoid slipping or falling.
D. See manufacturer’s instructions for proper operation and installation of
accessories.
E. Never use the machine without ensuring that all guards and shields are in
place.
F. Never, under any conditions, remove, bend, cut, fit, weld, or otherwise
alter standard parts on the Wood Chipper. This includes all shields and
guards. Modifications to your machine could cause personal injuries and
property damage and will invalid your warranty.
G. If the machine start to make an unusual noise or vibrate, shut down the
engine, disconnect the spark plug wire, keeping it away from the spark plug to
prevent accidental starting, wait 5 minutes for engine to cool down, then
inspect for damage.
Vibration is generally a warning of trouble. Check damaged parts and clean,
repair and/or replace as necessary.
H. Never tamper with safety devices. Check their proper operation regularly.
I. Before performing any maintenance or inspection procedure, shut down the
engine, disconnect the spark plug wire keeping it away from the spark plug to
prevent accidental starting, wait 5 minutes for machine to cool down.
J. Never allow people who are unfamiliar with these instructions to use the
Wood Chipper.
Allow only responsible individuals who are familiar with these rules of safe
operation to use your machine.
K. Never overload or attempt to chip woods beyond the manufacturer’s
recommendation.
It could result in personal injury or damage to the machine.
L. While using, don’t hurry or take things for granted. When in doubt about
the equipment or your surroundings stop the machine and take time to look
things over.
M. Never operate the machine when under the influence of alcohol, drugs, or
medication.
N. Use the machine only in daylight.
O. Stay alert for hidden hazards or traffic.
P. Keep all nuts and bolts tight and keep the equipment in good operating
condition.
A Note to All Users
List of warnings and cautions cannot be all-inclusive. If situations occur that are not covered by this manual, the operator must apply common sense and operate this WOOD CHIPPER in a safe manner. Contact the dealers for assistance in your area.
PART II: Familiar with the Wood Chipper
It may be helpful to familiarize yourself with the controls and features of
the Wood Chipper.
If you have any question, please contact the dealers in your area.
TECHNICAL SPECIFICATIONS
| Recoil Start
---|---
Engine| 7HP four strokes
Power| Gasoline/petrol
Chipper Capacity| 1CBM/hour to 3CBM/hour
Wood Diameter| diameter 60mm
Permitted wood width| 60mm
Chipper Blade| twin blades
Tire| 4.1/3.5-4
Overall Height| 1178mm
Overall Length| 1050mm
Width| 940mm
weight| 52/56kgs
Roller Max RPM| 3600
Noise at ear LpA, dB(A)
K=3 dB(A)| 91.8
Guaranteed sound power level
LwA, dB(A)| 111
PART III: Operating the Wood Chipper
It may be helpful to better familiarize yourself with the features of your Wood Chipper before beginning the steps outlined in this chapter.
WARNING
A. Read and understand all instructions, safety precautions, and/or warnings
listed in “PART I: General Safety Rules” before operating the WOOD CHIPPER. If
any doubt or question arises about the correct or safe method of performing
anything found in this manual, please contact the dealers in your area.
B. When operating the Wood Chipper, make sure you are standing in the safe
operating area (OPERATOR ZONE). You must stay in the safe operating area at
all times when the ram is in motion (whether extending or retracting). Never
place any part of your body into a position that causes an unsafe operating
condition.
C. Before loading and operating the Wood Chipper, always wear protective gear,
including safety goggles, hearing protection, tight-fitting gloves without
draw strings or loose cuffs, and steel-toed shoes.
D. Knowing the correct and incorrect methods of Chipping woods. Never using an
incorrect or unsafe method.
E. Only operate the machine in open space (e.g. not close to a wall or other
fixed object) and on a firm, level surface.
F. Do not operate the machine on a paved or gravel surface where ejected
material could cause injury.
G. Do not allow hands or any other part of the body or clothing inside the
feeding chamber, discharge chute, or near any moving part.
H. Leep proper balance and footing at all times. Do not overreach. Never stand
at a higher level than the base of the machine when feeding material into it.
I. When feeding material into the machine be extremely careful that pieces of
metal, rocks, bottles, cans or other foreign objects are not included.
J. If the machine becomes clogged at the inlet opening or discharge chute
shut-off the power source and disconnect the spark plug wire or remove the
ignition key(electric start only) before clearing debris in the inlet opening
or discharge chute. Keep the power source clear of debris and other
accumulations to prevent damage to the power source or possible fire. Remember
that operating the starting mechanism on engine powered machines will still
cause the cutting means to move.
K. Do not operate at the position where the exhaust-pipe direct, nor in the
direction in which the wind is blowing.
Assemble the Wood Chipper
Parts display when unpacking
Ref.No. | Description | Ref.No. | Description |
---|---|---|---|
1 | Base plate | 5 | Infeed bottom part |
2 | Wheel axle | 6 | Infeed top part |
3 | Wheel | 7 | discharge |
4 | Mainbody |
1. Wheel assembling
A. Assemble the wheel axle(2) to the base plate(1).
B. Assemble the wheels(3) to the wheel axle(2) and secure with the pin(7).
2. Assemble the mainbody(3) to the base plate(1)
3. Assemble the infeed bottom part(4) to the mainbody(3)
4. Assemble the infeed top part(4) to the infeed bottom part(3).
5. Assemble the discharge(5) to the mainbody(3).
Starting
1. Make sure the discharge is well assembled and the switch is pressed.
2. Make sure all attachments are well fastened with bolts.
3. Position your Wood Chipper on flat, dry ground, make sure the machine
cannot be moved by vibration.
4. Make sure the fuel shut-off valve is in the “ON” position.
5. Move the choke control lever to the “CHOKE” position (should only be
needed if the engine is cold).
6. Move the throttle control lever to the “FAST” or middle position.
7. Recoil Start: Turn the Ignition Switch to the “On” position. Grasp the
recoil starter handle and slowly pull until you feel resistance. Let the cord
retract a little bit then pull the cord rapidly to start the engine. One or
two pulls usually starts the engine.
8. Move the choke control lever (if used for cold engine) slowly back to the
“RUN” position when the engine is running well.
9. If the Wood Chipper has not been running (cold engine), warm up the engine
by running the engine at half throttle for 3 to 4 minutes, then advance the
engine throttle
Stopping
1. Move the Throttle Lever to IDLE.
2. Recoil Start: Turn the Ignition Switch to the OFF position.
3. Electric Start: Turn the Key to the OFF position.
Wood Chipping
NOTICE
Woods’ and branches’ diameter should be no bigger than 50mm.
WARNING
Do not place your hands into the chute when loading. This is a very UNSAFE
method and could result in injury to your hands.
Do not reach or step across the rail while the Wood Chipper is running. This
is a very UNSAFE method which could cause personal injury, even death.
When Blocked
If the disk stops while chipping woods or branches, the engine should be
stopped, and take out the woods which stuck the roller, and then restart the
engine, and chip again.
Disassemble the discharge
Before take off the discharge hopper, make sure the engine is shut down.
Remove the bolt according below figure shows from 1st to 4th.
Disassemble the infeed hopper
Before take off the infeed hopper, make sure the engine is shut down.
Remove the bolt according below figure shows from 1st to 4th.
PART IV: Maintaining the Wood Chipper
Regular maintenance is the way to ensure the best performance and long life of your machine. Please refer to this manual and the engine manufacturer’s user manual for maintenance procedures.
WARNING
Before performing any maintenance procedure or inspection, stop the engine, wait five minutes to allow all parts to cool. Disconnect the spark plug wire, keeping it away from the spark plug. Disconnect the Battery Terminals (Electric start only).
Regular Maintenance Checklist
Engine Service
Refer to the engine manufacturer’s user manual for engine maintenance.
Lubrication
NOTICE
All Bearings of your Chipper are sealed units and should have sufficient lubricant to last the life of your machine with normal use.
PART V: Troubleshooting and Parts List
Most problems are easy to fix. Consult the Troubleshooting Table below for common problems and their solutions. If you continue to experience problems, contact the dealers in your area.
WARNING
Before performing any maintenance procedure or inspection, stop the engine,
wait five minutes to allow all parts to cool. Disconnect the spark plug wire,
keeping it away from the
spark plug.
Troubleshooting Table
SYMPTOM | POSSIBLE CAUSE |
---|---|
The engine won’t start. | Ø Is the ignition switch in the “ON” position? |
Ø Is the fuel shut-off valve on?
Ø Are you using fresh, clean gas? If the gas is old, change it. Use a fuel
stabilizer if you keep gas longer than 30 days.
Ø Is the spark plug clean? If the spark plug is dirty or cracked, change it.
If it’s oily, leave it out, hold a rag over the plug hole and
pull the recoil cord several times to blow out any oil in the cylinder, then
wipe off the plug and reinsert it.
(Please refer to the
engine user manual
for engine-specific
procedures.)
The engine lacks power or is not running smoothly.| Ø Check that the
Throttle Lever is in the “Run” position.
Ø Is the air filter clean? If it’s dirty, change it following
the procedure in the engine manufacturer’s owner’s manual.
Ø Is the spark plug clean? If it’s fouled or cracked, change it. If it’s
oily, leave it out, hold a rag over the plug hole and pull your
recoil cord several times to blow out any oil in the cylinder, then wipe
off the plug and reinsert it.
Ø Are you using fresh, clean unleaded gas? If it’s old, change it. Use a
fuel stabilizer if you keep gas longer than 30 days.
Ø Does your engine have the right amount of clean oil? If it’s dirty,
change it following the procedure in the engine manufacturer’s owner’s
manual.
Ø Check the oil level and adjust as needed.
(Please refer to the engine user manual for engine-specific procedures.)
Engine smokes.| Ø Check the oil level and adjust as needed.
Ø Check the air filter and clean or replace if needed.
Ø You may be using the wrong oil—too light for the temperature.
Refer to your Engine Owner’s Manual for detailed information.
Ø Clean the cooling fins if they’re dirty.
(Please refer to the engine user manual for engine-specific procedures.)
Machine does not seem to have full chipping
power.| Ø The belts may be too loose and slipping. Adjust or replace belts
as need.
Explosion View and parts list
Ref.No. | Description | Ref.No. | Description |
---|---|---|---|
1 | Blade | 13 | Large washers A and C |
2 | Disc plate | 14 | Wheel |
3 | M8*100 Bolt | 15 | Fan sheet |
4 | Discharge | 16 | Round cover |
5 | anti-loosening sheet | 17 | Wheel axle |
6 | Emergency stop switch | 18 | Depression bar |
7 | Engine | 19 | Resist rubber sheet |
8 | Engine plate | 20 | Infeed top part |
9 | Blade disc frame | 21 | Infeed bottom part |
10 | Three holes of small | ||
buckle | 22 | Semicircular head square |
neck bolts M8*45
11| Base plate| 23| Tube cover
12| Rubber foot bar| |
Specifications:
-
Product: Wood Chipper
-
Intended Use: Chipping wood
-
Safety: High-powered machine with safety labels and precautions
-
Training: Operators must be fully trained before use
-
Maintenance: Regular service and blade checks required
-
-
FAQ:
Q: What should I do if I notice any damage to the machine?
A: If you notice any damage to the machine, stop using it immediately and contact a qualified technician for inspection and repair.
Q: Can I use materials other than wood in the wood chipper?
A: No, the wood chipper is designed solely for chipping wood. Do not use any other materials to avoid damage to the machine and ensure safe operation.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>