SENECA T203PM100-MU Energy Power Meters Instruction Manual

INSTALLATION MANUAL
T203PM100-MU
T203PM300-MU
T203PM600-MU

PRELIMINARY WARNINGS

The word WARNING preceded by the symbol **indicates conditions or actions that put the user’s safety at risk.
The word ATTENTION preceded by the symbol **indicates conditions or actions that might damage the instrument or the connected equipment. The warranty shall become null and void in the event of improper use or tampering with the module or devices supplied by the manufacturer as necessary for its correct operation, and if the instructions contained in this manual are not followed.

**| WARNING:** The full content of this manual must be read before any operation. The module must only be used by qualified electricians. Specific documentation is available via QR-CODE shown on page 1.
---|---
| The module must be repaired and damaged parts replaced by the Manufacturer. The product is sensitive to electrostatic discharges. Take appropriate measures during any operation.
| Electrical and electronic waste disposal (applicable in the European Union and other countries with recycling).
The symbol on the product or its packaging shows the product must be surrendered to a collection centre authorized to recycle electrical and electronic waste.

This document is the property of SENECA srl. Copies and reproduction are prohibited unless authorised.
The content of this document corresponds to the described products and technologies.
Stated data may be modified or supplemented for technical and/or sales purposes.
MI00562-3-EN
INSTALLATION MANUAL

MODULE LAYOUT

Dimensions LxHxD 95 x 75 x 35 mm; Weight: ≈ 150 g; Enclosure: PA6, black

SIGNALS VIA LED ON FRONT PANEL

ASSEMBLY

The device can be mounted in any position, in compliance with the expected environmental conditions.
CAUTION
Magnetic fields of considerable magnitude can alter the measurement: avoid proximity to permanent magnetic fields, solenoids or ferrous masses which induce strong alterations of the magnetic field; possibly, if the zero error is greater than the declared error, try a different arrangement or change orientation.

USB PORT

The front USB port allows easy connection to configure the device using the configuration software. If it is necessary to restore the initial configuration of the instrument, use the configuration software.
Through the USB port it is possible to update the firmware (for further information please refer to the Easy Setup 2 software).

To restore communication on the RS485 port, the cable must be physically disconnected from the USB port.
CAUTION
Check that the device in question is included in the list of products supported by the Easy Setup APP in the store.
When the USB port is connected to a cable, communication on the RS485 port is blocked.

TECHNICAL SPECIFICATIONS

CERTIFICATIONS|

https://www.seneca.it/products/t203pm100-mu/doc/CE_declaration

---|---
INSULATION| Using an insulated conductor. its sheath determines the insulation voltage. An insulation of 3 kVac is guaranteed on bare conductors.
ENVIRONMENTAL CONDITIONS| Temperature: -25 + +65 °C
Humidity. 10% + 90% non condensing.
Altitude: Up to 2000 m above sea level
Storage temperature: -30 + +85°C
Degree of protection: IP20.
ASSEMBLY| 35mm DIN rail IEC EN60715, suspended with ties
CONNECTIONS| Removable 6-way screw terminals, 5 mm pitch for cable up to 2.5 rnm1 micro US8
POWER SUPPLY| Vottage: on Vic and GND terminals, 11 + 28 Vdc Absorption: Typical: < 70 mA (/ 24 Vdc
COMMUNICATION
PORT| RS4.85 serial port on terminal Nock with ModBUS protocol (see user manual)
INPUT| Type of measurement ACOC TRMS or DC Bipolar Live: 1000Vdc; 290Vac
Crest factor 100A =1.7 ;300A= 1.9 ;600A= 1.9 Pass-band: 1.4 kHz
Overload: 3 x IN continuous
CAPACITY| =DC True MS| TRMS DC Bipolar (DIP7MDN)
T203PM600-MU| 0 – 600A / 0 – 290Vac| -600 – +600A / 0 – +1000Vdc
7203PM300•MU| 0 – 300A/ 0 – 290Vac| -300 – +300A 1 0 – +1000Vdc
T203P11100-MU| 0 – 100A I 0 – 290Vac| -100 – +100A / 0 – +1000Vdc
ANALOGUE OUTPUT| Type: 0 -10 Vdc, minimum load Rith, =2 kn.
Protection: Reverse polarity protection and over voltage prceedion
Resolution: 13.5 full scale AC
EMI error < 1 %
The type of output can be selected via software
DIGITAL OUTPUT| Type: active. 0 – Vcc, maximum load 50mA
The type of output can be selected via software
ACCURACY| below 3% of full scale| 1% of ful scale at 50160 Hz, 23°C
above 3% of full scale| 0,5% of full scale at 50160 Hz, 23°C
Coetlic. Temperature: < 200 ppmrC
Hysteresis on measurement 0.3% of full scale
Response speed: 500 ms (DC); 1 s (AC) at 99.5%
OVERVOLTAGE CATEGORIES| Bare conductor. CAT. III 600V
Insulated conductorOAT.III lkV

ELECTRICAL CONNECTIONS

WARNING
Disconnect the high voltage before carrying out any work on the instrument.
CAUTION
Switch off the module before connecting the inputs and outputs.
To meet electromagnetic immunity requirements:
– use properly insulated and dimensioned cables;
– use shielded cables for signals;
– connect the shield to a preferred instrumentation ground;
– Keep shielded cables away from other cables used for power installations (transformers, inverters, motors, etc.).

POWER SUPPLY| ANALOGUE OUTPUT| DIGITAL OUTPUT| RS485| MEASUREMENT INPUT
---|---|---|---|---
| | | |

CAUTION
Make sure that the direction of the current flowing through the cable is that shown in the figure (incoming).
To increase the sensitivity of the current measurement, insert the cable several times into the central hole of the instrument, creating a series of loops.
The current measurement sensitivity is proportional to the number of cable passages through the hole.

CONTACT INFORMATION

Technical support| support@seneca.it| Product information| sales@seneca.it
---|---|---|---

www.seneca.it/products/t203pm300-mu
DOCUMENTATION
SENECA s.r.l.; Via Austria, 26 – 35127 – PADOVA – ITALY;
Tel. +39.049.8705359 –
Fax +39.049.8706287
MI00562-3-EN

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>