GE 19299 Door Chime Instruction Manual

GE 19299 Door Chime

Installation instructions

Required tools: Small flat blade screwdriver, #2 Phillips screwdriver and 1/16” drill bit (not included) The wireless door chime kit has two components:

Installing battery in push button

1. Remove the front cover of the push button housing by pushing a flat blade screwdriver into the slot at the bottom of the push button housing
2. Install the CR2032 battery (included) with the positive(+) side up.
3. Keep the front cover off the push button until melody selection is complete.

Pairing the transmitter push button(s) to chime receiver

NOTE : the chime and push button(s) come paired in the package. Once the battery is installed in the push button and chime is plugged in, press the push button(s) to ensure the chime sounds. IF CHIME DOES NOT SOUND, FOLLOW DIRECTIONS BELOW TO PAIR THE PUSH BUTTON TO THE CHIME

1. To clear settings: Press and hold the pairing button on the bottom of the chime while plugging the chime into the outlet.
2. Once chime is plugged in, release the Pairing button.
3. Press and hold the Pairing button again. You will hear the “Ding Dong” melody twice, and then the double beep to alert you the chime is ready to pair with the push button. Release the pairing button.
4. Press and release the push button You will hear one beep letting you know the chime accepted the signal.
5. Wait 10 seconds and you will hear the double beep again to alert you the chime is now paired with the push button.
6. Press the push button to test.

Melody Selection Setting
(your chime will have either 2 or 8 melodies) Select the melody by pushing the Melody selection button located inside the push button housing (See Figure 1). Press and release the melody selection button until you hear the desired melody. Table 1 and Table 2 shows the order the melodies will be heard. The last melody played will be your selected chime melody.

Table 1 – 2 Melody Chime

1. Dingdong
2. Westminster

Table 2 – 8 Melody Chime

1. Dingdong
2. Westminster
3. Knocks (3 times)
4. Fanfare
5. Mozart
6. Good Vibes
7. Patriotic
8. Tango

Volume Adjustment

There are four volume settings on this chime

1. To adjust the volume, press and release the pairing button on the chime to play the melody.
2. While melody is playing, press and release the volume button on the chime to select the desired sound level

Push button mounting instructions

NOTE : Avoid mounting on metal surfaces, as it may result in a reduced range of transmission. Do not mount in an area exposed to direct rain. Push buttons are typically mounted at the same height as the door knob or handle (between 36” and 44” above the floor).

Permanent mounting instructions

1. Remove the front cover of the push button
2. Before mounting, choose a mounting location that is no further than 150 feet from the chime unit location. Place the push button where you would like to mount and test with the chime as close to its final location as possible. If it works, continue with mounting the button. If it does not work, see TROUBLESHOOTING.
3. Hold the back plate of the push button in the selected location with the arrow on the back of the back plate pointing up.
4. Using the 1/16” drill bit, drill a hole through the back plate of the push button (See Figure 4 — Mounting hole locations) and into the surface of the selected location.
5. Secure with the two screws provided.
6. Press front housing onto back cover.
7. Test operation. If chime does not work, see TROUBLESHOOTING.

Temporary mounting instructions

1. Clean the mounting location for the push button with a mixture of 50% water and 50% isopropyl alcohol.
2. Remove protective backing from one side of the adhesive pad and attach it to the back plate of the push button.
3. Remove protective backing from the other side of the adhesive pad and press the back plate to the cleaned mounting location and hold in place for a few seconds to allow for a secure bond.

Chime mounting instructions
Plug the chime into the top receptacle of the outlet

Troubleshooting

If the chime does not work:

1. Make sure push button switch is pressed down and held for at least 1 second.
2. Verify battery installation is correct, noting polarity.
3. Try a fresh battery in push button.
4. Make sure chime is no further than 150 feet away from push button.
5. Ensure push button is not mounted on metal, near metal studs, or near the floor.
6. Try a new location for the chime

Functional range may be adversely affected by one or more of the following factors: weather, radio frequency interference, low transmitter battery, and obstructions between the transmitter and receiver

FCC STATMENT

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC NOTE : The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.

NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encourage to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

MADE IN CHINA
GE is a trademark of General Electric Company and is under license by Jasco Products Company LLC, 10 E. Memorial Rd., Oklahoma City, OK 73114. This Jasco product comes with a 90-day limited warranty. Visit www.jascoproducts.com for warranty details and product registration. Questions? Contact us at 1-800-654-8483 between 7:30AM—5:00PM CST.

CAUTION

• BATTERIES MAY LEAK HARMFUL LIQUIDS OR IGNITABLE MATERIALS OR EXPLODE CAUSING INJURY AND PRODUCT DAMAGE
• DO NOT MIK OLD AND NEW OR OTHER BATTERY TYPES
• REPLACE ALL BATTERIES AT THE SAME TIME
• REPLACE EXHAUSTED BATTERIES IMMEDIATELY
• REMOVE BATTERIES IF PRODUCT IS TO BE UNUSED FOR EXTENDED OF TIME

WARNING
RISK OF ELECTRIC SHOCK

• KEEP CHILDREN AWAY
• FULLY INSERT PLUG
• USE IND0ORS ONLY
• DO NOT USE IN WET
• LOCATIONS

19298 19299 19300 Version 05 10/21/2014

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>