SCHUBERTH SC2 Communication System Instruction Manual
- June 1, 2024
- SCHUBERTH
Table of Contents
- SCHUBERTH SC2 Communication System
- ABOUT THE SC2
- INSTALLING THE HEADSET ON YOUR HELMET
- GETTING STARTED
- PAIRING THE HEADSET WITH OTHER BLUETOOTH DEVICES
- MOBILE PHONE USAGE
- STEREO MUSIC
- MESH INTERCOM
- BLUETOOTH INTERCOM
- USING THE FM RADIO
- VOICE COMMAND
- FUNCTION PRIORITY
- CONFIGURATION SETTING
- TROUBLESHOOTING
- ABOUT COMPANY
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
SCHUBERTH SC2 Communication System
ABOUT THE SC2
Product Details
SC2
SC2 Remote Control
Package Contents
Optional Accessories
Contact SCHUBERTH or your authorized dealer for accessories.
INSTALLING THE HEADSET ON YOUR HELMET
Installing the SC2 Remote Control
-
Remove the cover for the SC2 Remote Control from your helmet.
-
Slide and insert the SC2 Remote Control onto your helmet.
Installing the SC2
-
Remove the SC2 cover from the helmet by lifting it up with the SC2
Remote Control cover. -
Pull out the antenna cable retainer from its original position, and pull out the antenna cables from the upper gap in the space. Then, connect the SC2’s antenna cables and the helmet’s antenna cables correctly.
- Put the antenna cable retainer back into its original position, and put the connected cables into the upper gap in the space.
Note: Make sure that the antenna cable retainer and the connected cables are positioned correctly before installing the SC2. If not, the cables may be damaged or interference may occur.
- Install the SC2 into the helmet.
Removing the SC2
-
Remove the installed SC2 from the helmet by lifting it up with the SC2 Remote Control cover.
-
Pull the antenna cable retainer out from its original position, and pull out the connected cables from the upper gap in the space. Then, disconnect the cables correctly.
Note: When you need to un-plug the connectors, please wiggle and pull them. It will help the connector connection be released more easily.
- Put the antenna cable retainer back into its original position, and put the helmet’s cables into the upper gap in the space.
Installing the Microphone (The Microphone Is Pre-Installed on the S3)
-
Remove the microphone rubber cap as shown in the illustration to install the microphone.
-
Install the microphone by pressing firmly on the area marked with the orange circle.
GETTING STARTED
Legend
Function = Button(s) to tap the specified amount of number of times or press and hold for the specified amount of time.
Downloadable Software
SCHUBERTH SC2 App
By simply pairing your phone with your headset, you can use the SCHUBERTH SC2 App for quicker and easier set up and management.
- App functions: Mesh Intercom, Bluetooth Intercom, Music, Device settings, Language settings
- Download
- Android: Google Play Store > SCHUBERTH SC2
- iOS: App Store > SCHUBERTH SC2
SCHUBERTH Device Manager
The SCHUBERTH Device Manager allows you to upgrade the firmware and configure
its settings directly from your PC or Apple computer. Download the SCHUBERTH
Device Manager from oem.sena.com/schuberth/.
Powering On and Off
SC2 Powering On and Off
- To switch on the SC2, hold the Multi-function Button for 2 seconds.
- To switch off the SC2, hold the Multi-function Button for 2 seconds until you hear the double beep.
Powering On/Off
- The remote control switches to sleep mode when you switch off the SC2.
- To wake up the remote control after starting the SC2, tap (+) Button on the remote control.
SC2 Remote Control Powering On and Off
-
To begin using the SC2 Remote Control, remove the plastic strip from the battery slot.
-
Tap the Center Button.
Powering On -
Press and hold the (+) Button and the Center Button for 3 seconds.
Powering Off
Note: The SC2 and the SC2 Remote Control come paired together. They will automatically connect to each other when the SC2 and the SC2 Remote Control are powered on.
Charging the SC2
Charging the Headset
The headset will be fully charged in about 2.5 hours. (The charging time may
vary depending on the charging method.)
Note:
- Please make sure to take off your SC2-installed helmet while charging. The headset automatically turns off during charging.
- Any USB charger can be used with the headset if the charger is approved by either the FCC, CE, or IC.
- The SC2 is compatible with 5 V/1 A input USB-charged devices only.
Replacing the Battery
To replace the discharged battery of the SC2 Remote Control, follow the steps
below:
-
Prepare a CR2016 Lithium 3 V coin battery for the SC2 Remote Control.
-
Open the battery slot’s cover.
-
Insert a paper clip into the Battery Release Hole. Then, change the discharged battery with the new battery.
-
Insert the new battery into the battery slot.
-
Close the battery slot’s cover. When closing the cover, insert the cover’s two battery guides first.
Checking the Battery Level
When switching on, the LED flashes red to indicate the charge level.
Note: When the SC2’s battery is low while in use, you will hear a voice prompt saying “Low battery.”
Volume Adjustment
You can raise or lower the volume by tapping the (+) Button or the (-) Button.
Volume is set and maintained independently at different levels for each audio
source (i.e., phone, intercom), even when the headset is rebooted.
PAIRING THE HEADSET WITH OTHER BLUETOOTH DEVICES
When using the headset with other Bluetooth devices for the first time, they
will need to be “paired.” This enables them to recognize and communicate with
one another whenever they are within range.
The headset can pair with multiple Bluetooth devices such as a mobile phone,
GPS, MP3 player, or Sena SR10 Two-Way Radio Adapter via Mobile Phone Pairing,
Second Mobile Phone Pairing, and GPS Pairing. The headset can also be paired
with up to three other SCHUBERTH headsets.
Phone Pairing
- Press and hold the Center Button for 10 seconds.
- Tap the (+) Button.
- With your mobile phone in Bluetooth-pairing mode, select SC2 in the list of devices detected.
If your mobile phone asks for a PIN, enter 0000.
Second Mobile Phone Pairing – Second Mobile Phone, GPS, and SR10
- Press and hold the Center Button for 10 seconds.
- Double tap the (+) Button.
- With your mobile phone in Bluetooth-pairing mode, select SC2 in the list of devices detected.
If your device asks for a PIN, enter 0000.
Advanced Selective Pairing: Hands-Free or A2DP Stereo
Phone Pairing allows the headset to establish two Bluetooth profiles: Hands- Free or A2DP Stereo. Advanced Selective Pairing allows the headset to separate the profiles to enable connection with two devices.
- Phone Selective Pairing – Hands-Free Profile
- Press and hold the Center Button for 10 seconds.
2. Tap the (+) Button three times.
3. Select SC2 in the list of Bluetooth devices detected.
If your mobile phone asks for a PIN, enter 0000.
Media Selective Pairing – A2DP Profile
- Press and hold the Center Button for 10 seconds.
- Tap the (+) Button four times.
- Select SC2 in the list of Bluetooth devices detected.
If your mobile phone asks for a PIN, enter 0000.
GPS Pairing
- Press and hold the Center Button for 10 seconds.
- Tap the (+) Button five times.
- Select SC2 in the list of Bluetooth devices detected.
If your device asks for a PIN, enter 0000.
Note: If you pair your GPS device via GPS Pairing, its instruction will
not interrupt your Mesh Intercom conversations, but overlay with them.
Bluetooth intercom conversations will be interrupted by GPS instructions.
MOBILE PHONE USAGE
Making and Answering Calls
Note: If you have a GPS device connected, you will not hear its voice navigations during a phone call.
Siri and Google Assistant
The headset supports the Siri and Google Assistant access directly. You can
activate the Siri or Google Assistant using the voice through the headset’s
microphone, a wake word will be used. This is a word or a group of words such
as “Hey Siri” or “Hey Google.”
Activate the Siri or Google Assistant installed on Your Smartphone
Speed Dialing
Assigning Speed Dial Presets
Speed Dial Presets could be assigned through the SCHUBERTH SC2 App or the
SCHUBERTH Device Manager.
Using Speed Dial Presets
- Press and hold the (+) Button for 3 seconds.
Enter Speed Dial Mode
- Tap the (+) Button or the (-) Button to navigate between the menus.
Navigate Forward or Backward through Speed Dial Preset Numbers
1. Last number redial
2. Speed dial 1
3. Speed dial 2
4. Speed dial 3
5. Cancel
- To call one of your Speed Dial Presets, tap the Center Button.
Call a Speed Dial Preset Number
- To redial the last phone call number, tap the Center Button.
Redial Last Number
STEREO MUSIC
Bluetooth Stereo Music
Music Sharing
You can start sharing music with one intercom friend using Bluetooth stereo
music during a two-way intercom conversation and one participant of a Mesh.
If you start sharing music while Bluetooth intercom and Mesh Intercom are
running at the same time, then music shared during Bluetooth intercom will
take priority over music shared during Mesh Intercom.
Note:
- Both you and your intercom friend can remotely control music playback such as track forward and track back.
- Music sharing will be paused when you are using your mobile phone or listening to GPS instructions.
- Music sharing will be terminated if the headset starts a multi-way intercom conference.
Bluetooth Intercom Music Sharing
- You can start sharing music with one intercom friend of a two-way intercom conversation.
- Press and hold the (-) Button for 3 seconds.
Start/Terminate Sharing Music
Mesh Intercom Music Sharing
You (Creator) can start sharing music with one participant of a Mesh Intercom.
- To send a request message to participants connected during Mesh Intercom, press and hold the (-) Button for 3 seconds.
- You (Creator) can share music with the first participant that accepts the request by tapping the Mesh Intercom Button.
MESH INTERCOM
What is Mesh Intercom?
- Mesh Intercom™ is a dynamic communication system that provides instant and effortless bike-to-bike communication without a pre-grouping process. Mesh Intercom allows riders to connect and communicate with nearby users without the need to pair each headset together.
- Within the same channel in Open Mesh™ or the same private group in Group Mesh™, six users can talk at the same time and enjoy the optimal quality for their conversation.
Open Mesh
- Open Mesh is an open group intercom function. Users can freely communicate with each other in the same Open Mesh channel and select which channel (1-9) to use through the headset.
- It can connect with a virtually unlimited number of users in each channel.
Group Mesh
- Group Mesh is a closed group intercom function that allows users to join, leave, or rejoin a group intercom conversation without pairing each headset. Users can freely communicate with each other in the same private group in Group Mesh.
- For closed intercom conversations using Mesh Intercom, a Group Mesh needs to be created by the users. When users create a private group in Group Mesh by Mesh Grouping, the headset automatically switches from Open Mesh to Group Mesh. Up to 24 users can all be connected in each private group.
Starting Mesh Intercom
When Mesh Intercom is enabled, the SC2 will automatically connect to nearby
all other Mesh users and allow them to talk to each other by tapping the Mesh
Intercom Button.
- **Mesh Intercom On
**
- **Mesh Intercom Off
**
Using the Mesh in Open Mesh
When Mesh Intercom is enabled, the headset will be in Open Mesh (default: channel 1) initially.
Channel Setting (Default: Channel 1)
If the Open Mesh communication experiences interference because other groups
are also using channel 1 (default), change the channel. You can select from
channels 1 to 9.
- Double tap the Mesh Intercom Button.
- Tap the (+) Button or the (-) Button to navigate between channels.
- Tap the Center Button to save the channel.
Note:
1. Channel Setting always starts with channel 1.
2. If you do not press any button for approximately 10 seconds in a specific channel, the channel is automatically saved.
3. The channel will be remembered even if you turn off the headset.
4. You can use the SCHUBERTH SC2 App to change the channel.
Using Mesh in Group Mesh
Creating a Group Mesh
Creating a Group Mesh requires two or more Open Mesh users.
- To enter Mesh Grouping to create a Group Mesh, press and hold the Mesh Intercom Button for 5 seconds on the headset of You (C) and your friend (D).
- The headsets complete Mesh Grouping and automatically switch from Open Mesh to Group Mesh.
Note:
* If the Mesh Grouping is not completed within 30 seconds, users will hear a voice prompt, “Grouping failed.”
* If you want to cancel during the Mesh Grouping, tap the Mesh Intercom Button.
Joining an Existing Group Mesh
One of the members in an Existing Group Mesh can allow new members in Open
Mesh to join the Existing Group Mesh.
- To enter Mesh Grouping to join the Existing Group Mesh, press and hold the Mesh Intercom Button for 5 seconds on the headset of One of the current members (E) and a new member (you [C]).
- The headsets complete Mesh Grouping. The new members will hear a voice prompt as their headsets automatically switch from Open Mesh to Group Mesh.
Note: If the Mesh Grouping is not completed within 30 seconds, the current members will hear a low tone double beep and the new member will hear a voice prompt, “Grouping failed.”
Enable/Disable Mic (Default: Enable)
Users can enable/disable the microphone when communicating in a Mesh Intercom.
Toggling Open Mesh/Group Mesh
- Users are able to toggle between Open Mesh and Group Mesh without resetting the Mesh. This allows users to keep the Group Mesh Network connection information while in Open Mesh.
- Users can toggle to Group Mesh to communicate with participants from the stored Group Mesh Network connection information.
Toggle Between Open Mesh and Group Mesh
Note: If you have never participated in Group Mesh, you cannot toggle between Open Mesh and Group Mesh. You will hear a voice prompt, “No group available.”
Mesh Reach-Out Request
You (caller) can send a request message to turn on the Mesh Intercom to
nearby* friends who have it turned off.
- If you want to send or receive a request message, you need to enable Mesh Reach-Out on the SCHUBERTH SC2 App. Please refer to Section 12.2: “Software Configuration Setting.”
- While your headset’s Mesh Intercom is on, you (caller) send a request message using the headset’s Button or the SCHUBERTH SC2 App.
-
Friends who receive the request message need to manually turn on their Mesh Intercom using the headset’s Button or the SCHUBERTH SC2 App.
Note:- *: Up to 100 m (109 yds) in open terrain
- To use the Mesh Reach-Out Request function, you (caller) who sends a request message and the friends who receive the request message must update the headset to the latest firmware version and the app to the latest version.
Reset Mesh
If a headset in an Open Mesh or Group Mesh resets the Mesh, it will
automatically return to Open Mesh (default: channel 1).
BLUETOOTH INTERCOM
Up to three people can communicate via intercom with the headset simply by
pairing their headsets.
Pairing with Intercom Friends ****
Note: If the SC2 communication system is installed on full Carbon helmets, the
maximum range of communication is limited to 400 meters in open terrain
without obstacles, due to the electromagnetic interference shielding
properties of the carbon fiber.
Intercom Pairing
There are two ways to pair the headset.
Using the Smart Intercom Pairing (SIP)
SIP allows you to quickly pair with your friends for intercom communication by
scanning the QR code on the SCHUBERTH SC2 App without remembering the button
operation.
-
Pair the mobile phone with the headset.
-
Open the SCHUBERTH SC2 App and tap (Smart Intercom Pairing Menu).
-
Scan the QR code displayed on your friend (B)’s mobile phone.
Your friend (B) can display the QR code on the mobile phone by tapping > QR code on the SCHUBERTH SC2 App. -
Tap Save and check that your friend (B) is paired with you (A) correctly.
-
Tap Scan and repeat steps 3-4 to pair with Intercom Friends (C) and (D).
Note: The Smart Intercom Pairing (SIP) is not compatible with Sena products that use Bluetooth 3.0 or below.
Using the Button
- Press and hold the Center Button of two headsets for 5 seconds until you hear a voice prompt, “Intercom pairing.”
-
The SC2 will automatically pair with a SCHUBERTH headset.
-
Repeat the steps above to pair with Intercom Friends C & D.
Last-Come, First-Served
The intercom pairing queue is Last-Come, First-Served. If a headset has
multiple paired headsets for intercom conversations, the last paired headset
is set as the First Intercom Friend. For example, after the pairing procedures
listed above, headset (D) is the First Intercom Friend of headset (A). Headset
(C) is the Second Intercom Friend of headset (A), and headset (B) is the Third
Intercom Friend of headset (A).
Two-Way Intercom
You can start or end an intercom conversation with an Intercom Friend by
tapping the Center Button.
-
Tap once for Intercom Friend 1.
-
Tap twice for Intercom Friend 2.
-
Tap three times for Intercom Friend 3.
Multi-Way Intercom
Multi-Way Intercom enables conference-call-style conversations with up to three Intercom Friends at the same time. While Multi-Way Intercom is in progress, mobile phone connection is temporarily disconnected. However, as soon as Multi-Way Intercom terminates, the mobile phone connection will be reestablished.
Starting a Three-Way Intercom Conference
You (A) can have a Three-Way Intercom Conference with two other Intercom
Friends (B & C) by establishing two intercom connections simultaneously.
-
Pair your headset (A) with those of two other Intercom Friends (B & C).
Pair with Intercom Friends B & C, refer to Section 8.1: “Intercom Pairing” -
Start an intercom conversation with one of the two friends in your intercom group. For example, you (A) may start an intercom conversation with the Intercom Friend (B). Or, Intercom Friend (B) may start an intercom call with you (A).
Starting an Intercom Conversation with Intercom Friend B. -
Then, you (A) can call the Second Intercom Friend (C), or the Second Intercom Friend (C) may join the intercom by making an intercom call to you (A).
Starting an Intercom Conversation with Intercom Friend C -
Now you (A) and two Intercom Friends (B & C) are having a Three-Way Intercom Conference.
Three-Way Intercom
Starting a Four-Way Intercom Conference
With three Intercom Friends connected, a new participant (D) can make it a
Four-Way Intercom Conference by making an intercom call to either (B) or (C).
Starting a Four-Way Intercom
Ending Multi-Way Intercom
- Press and hold the Center Button for 3 seconds until you hear a beep to terminate all intercom connections.
- Tap the Center Button to disconnect from your First Intercom Friend.Double tap the Center Button to disconnect from your Second Intercom Friend.
Three-Way Conference Phone Call with Intercom Users
You can have a Three-Way Conference Phone Call by adding an Intercom Friend to
the mobile phone conversation.
-
During a mobile phone call, tap the Center Button once, twice, or three times to invite one of your Intercom Friends to the conversation.
Invite an Intercom Friend into Phone Conference -
To disconnect the intercom during a conference phone call, tap the Center Button once, twice, or three times.
Disconnect Intercom Friend from Conference -
To disconnect the mobile phone call during a conference phone call, press and hold the Center Button for 2 seconds.
End Phone Call from Conference
Note: When you have an incoming intercom call during a mobile phone call, you will hear high tone double beeps.
Group Intercom
Group Intercom allows you to instantly create a Multi-Way Conference Intercom
with three of the most recently paired headsets.
- Start the Group Intercom
1. Go through intercom pairing with up to three headsets you want to have Group Intercom with.
2. Tap the (+) Button and (-) Button to begin Group Intercom
- Terminate Group Intercom
To terminate Group Intercom, press and hold the Center Button for 3 seconds during Group Intercom.
Mesh Intercom Conference with Bluetooth Intercom Participant
Users can use the existing Bluetooth intercom and Mesh Intercom function at
the same time. In this case, it is recommended to communicate with other
SCHUBERTH headsets via Bluetooth intercom connection and use Mesh Intercom
between SC2 headsets. A user who is in Open Mesh or Group Mesh when using Mesh
Intercom is able to include up to 3 of their Bluetooth intercom friends. You
can start a Two-Way Intercom conversation with one of your three Intercom
Friends to include them in the Mesh.
Note:
-
The audio quality will be reduced if a SC2 connects to 2 or more Bluetooth intercom friends while in Open Mesh or Group Mesh when using Mesh Intercom.
-
If a closed loop is created, as shown below, each user will experience severe noise issues. SCHUBERTH recommends that a closed loop not be created.
-
If Bluetooth intercom is accidentally turned on during Mesh Intercom communication between SC2 headsets, as shown below, you will hear a voice prompt, “Mesh intercom disabled. Bluetooth intercom connected” every 1 minute. If you turn off the Bluetooth Intercom or turn off the Mesh Intercom, the voice prompt will no longer come out.
Universal Intercom
Universal Intercom allows you to have intercom conversations with users of
non-SCHUBERTH Bluetooth headsets. Non-SCHUBERTH Bluetooth headset can be
connected to the SCHUBERTH headset if they support the Bluetooth Hands-Free
Profile (HFP). You can pair your headset with only one non- SCHUBERTH headset
at a time. The intercom distance depends on the performance of the Bluetooth
headset to which it is connected. When a non- SCHUBERTH Bluetooth headset is
paired with the SCHUBERTH headset, if another Bluetooth device is paired via
Second Mobile Phone Pairing, it will be disconnected.
- Press and hold the Center Button for 10 seconds.
- Tap the (-) Button three times.
- Tap the Center Button.
-
Put the non-SCHUBERTH Bluetooth headset in Pairing Mode. The headset will automatically pair with a non-SCHUBERTH Bluetooth headset.
-
You can have Two-Way Intercom or Multi-Way Intercom communication with up to three Intercom Friends using non-SCHUBERTH headsets by following the procedures described below.
-
Example of a Three-Way Universal Intercom
-
Example of a Four-Way Universal Intercom
-
Note: Some non-SCHUBERTH headsets may not support Multi-Way Universal Intercom.
Mesh Intercom Conference with Two-way Universal Intercom Participant
- Users can use the existing Two-way Universal Intercom and Mesh Intercom function at the same time. In this case, it is recommended to communicate with non-SCHUBERTH headset via Two-way Universal Intercom connection and use Mesh Intercom between SC2 headsets.
- A user who is in Open Mesh or Group Mesh when using Mesh Intercom is able to include one Universal Intercom Friend. You can start a Two-way Universal Intercom conversation with your Universal Intercom Friend to include it in the Mesh.
USING THE FM RADIO
FM Radio On/Off
Seek and Save Radio Stations
The “Seek” feature searches for radio stations.
- Search for radio stations.
- Save the current station.
- Navigate through the preset numbers that you want to store.
- Save the station in the preset number you choose or delete the station from memory.
Scan and Save Radio Stations
The “Scan” function automatically searches for radio stations, starting with
the current station’s frequency, then up from there.
- Scan for stations.
- The SCHUBERTH tuner pauses at each station it finds for 8 seconds before moving to the next.
- Save the current station. The station will be saved as the next preset number.
- Stop scanning.
Note:
* You can use the SCHUBERTH Device Manager or the SCHUBERTH SC2 App to save the preset stations.
* If the SC2 is installed on full Carbon helmets the electromagnetic interference shielding properties of the carbon fiber shell can influence the clarity of FM signals.
Navigating Preset Stations
Using the methods above, up to 10 radio stations can be stored. You can
navigate through the saved stations.
Temporary Station Preset
The Temporary Preset feature automatically finds and saves the nearest 10
radio stations without changing your existing preset stations.
-
Automatically find and save 10 stations.
-
The temporary preset stations will be cleared when the headset reboots.
Region Selection
You can select the proper FM frequency range for your location from the
SCHUBERTH Device Manager or the SCHUBERTH SC2 App. Using the region setting,
you can optimize the seek function to avoid unnecessary frequency ranges.
Region | Frequency range | Step |
---|---|---|
Worldwide | 76.0 ~ 108.0 MHz | ± 100 kHz |
North America, South America and Australia |
87.5 ~ 107.9 MHz
|
± 200 kHz
Asia and Europe| 87.5 ~ 108.0 MHz| ± 100 kHz
Japan| 76.0 ~ 95.0 MHz| ± 100 kHz
VOICE COMMAND
The Voice Command of the headset allows you to operate certain operations by simply using your voice. You can control the headset completely hands-free using the voice recognition. Multi-language Voice Command supports English, French, German, Spanish, Italian, Chinese, Japanese, and Russian.
Speak a Voice Command List
Mode Status | Function | Voice Command |
---|
Standby/ Bluetooth Intercom/
Mesh Intercom/ FM Radio/ Music
| Check battery| “Hey Sena, Check Battery”
Volume Up| “Hey Sena, Volume Up”
Volume Down| “Hey Sena, Volume Down”
Phone Pairing| “Hey Sena, Phone Pairing”
Bluetooth Intercom Pairing|
“Hey Sena, Pairing Intercom”
Start/End each Bluetooth Intercom| “Hey Sena, Intercom [one, two, three]”
Standby/ Bluetooth Intercom/ FM Radio/ Music|
Turn on Mesh Intercom
|
“Hey Sena, Mesh On”
Mesh Intercom
| Turn off Mesh Intercom| “Hey Sena, Mesh Off”
Mesh Grouping| “Hey Sena, Mesh Grouping”
Switch to Open Mesh| “Hey Sena, Open Mesh”
Switch to Group Mesh| “Hey Sena, Group Mesh”
End the Bluetooth intercom and Mesh intercom|
“Hey Sena, End intercom”
Standby/ Bluetooth Intercom/ Mesh Intercom|
Play Music
|
“Hey Sena, Play Music”
Standby/ Intercom/
Mesh Intercom/ Music
|
Turn on FM radio
|
”Hey Sena, FM Radio On”
---|---|---
Music/ FM Radio
| • FM – Next Preset
• Music – Next Track
|
“Hey Sena, Next”
• FM – Previous Preset
• Music – Previous Track
|
“Hey Sena, Previous”
Music| Pause Music| “Hey Sena, Stop Music”
FM Radio| Turn off FM Radio| “Hey Sena, FM Radio Off”
Answer an Incoming Call| “Answer”
Ignore an Incoming Call| “Ignore”
Note:
- You can set a language to another language by using the Headset Language feature on the SCHUBERTH SC2 App.
- If you set a language that does not support voice commands, the voice command will work only with English commands.
- You can see the another language’s voice command list on the SCHUBERTH SC2 App.
- Voice command performance may vary based on the environmental conditions including riding speed, helmet type, and ambient noise.
FUNCTION PRIORITY
Function Priority
The headset prioritizes connected devices in the following order:
- (highest)
- Mobile phone
- Mesh Intercom/Bluetooth Intercom
- Music sharing via Bluetooth stereo music
- FM radio
- (lowest)
Bluetooth stereo music
A lower-priority function gets interrupted by a higher-priority function. For example, stereo music will be interrupted by an Intercom Conversation; an Intercom Conversation will be interrupted by an incoming mobile phone call.
CONFIGURATION SETTING
Headset Configuration Setting
Headset Configuration Menu
Voice Configuration Menu | Tap the Center Button |
---|---|
Phone Pairing | None |
Second Mobile Phone Pairing | None |
Phone Selective Pairing | None |
Media Selective Pairing | None |
GPS Pairing | None |
Delete All Pairings | Execute |
Universal Intercom Pairing | Execute |
Factory Reset | Execute |
Exit | Execute |
Delete All Pairings
Delete All Bluetooth Pairing Information stored in the headset.
Software Configuration Setting
You can change the settings of the headset through the SCHUBERTH Device Manager or the SCHUBERTH SC2 App.
Speed Dial
Assign phone numbers for speed dialing to make a phone call quickly.
Headset Language
You can select the device language. The selected language is maintained even
when the headset is rebooted.
Mesh Reach-Out (Default: Disable)
When the Mesh Reach-Out is enabled, a Mesh Reach-Out request message can be
sent or received. If the Mesh Reach-Out is disabled, a Mesh Reach- Out request
message cannot be sent or received.
Audio Equalizer (Default: Off)
You can use the Audio Equalizer to increase/decrease the decibel level of
different frequency ranges of audio.
- Balance will adjust all of the frequency ranges to be the same volume level (0 dB).
- Bass Boost will increase the bass range of audio (20 Hz – 250 Hz).
- Mid Boost will increase the mid range of audio (250 Hz – 4 kHz).
- Treble Boost will increase the high range of audio (4 kHz – 20 kHz).
VOX Phone (Default: Enable)
If this feature is enabled, you can answer incoming calls by voice. When you
hear a ringtone for an incoming call, you can answer the phone by saying a
word such as “Hello” loudly or by blowing air into the microphone. VOX Phone
is temporarily disabled if you are connected to intercom. If this feature is
disabled, you have to tap the Center Button to answer an incoming call.
VOX Intercom (Default: Disable)
If VOX Intercom is enabled, you can initiate an intercom conversation with the
last connected intercom friend by voice. When you want to start intercom, say
a word such as “Hello” loudly or blow air into the microphone. If you start an
intercom conversation by voice, the intercom terminates automatically when you
and your intercom friend remain silent for 20 seconds. However, if you
manually start an intercom conversation by tapping the Center Button, you have
to terminate the intercom conversation manually. However, if you start the
intercom by voice and end it manually by tapping the Center Button, you will
not be able to start intercom by voice temporarily. In this case, you have to
tap the Center Button to restart the intercom. This is to prevent repeated
unintentional intercom connections by strong wind noise. After rebooting the
headset, you can start the intercom by voice again.
VOX Sensitivity (Default: 3)
VOX Sensitivity can be adjusted depending on your riding environment. Level 5
is the highest sensitivity setting and level 1 is the lowest.
Bluetooth Intercom Audio Multitasking (Default: Disable)
Audio Multitasking (Bluetooth Intercom Audio Multitasking and Mesh Intercom
Audio Multitasking) allows you to have an intercom conversation while
simultaneously listening to music, FM radio, or GPS instructions. The overlaid
audio is played in the background with reduced volume whenever there is an
intercom conversation and will return to normal volume once the conversation
is finished.
The Mesh Intercom Audio Multitasking feature is always on.
Note:
- For Bluetooth Intercom Audio Multitasking to work properly, you need to power the headset off and on. Please restart the headset.
- Bluetooth Intercom Audio Multitasking will be activated during two-way intercom conversations with a headset that also supports this feature.
- Some GPS devices may not support this feature.
- The Audio Multitasking feature can be configured through the Intercom- Audio Overlay Sensitivity and the Audio Overlay Volume Management settings.
Intercom-Audio Overlay Sensitivity (Default: 3)
The music, FM radio, and GPS volume will be lowered to play in the background
if you talk over the intercom while the overlaid audio is playing. You can
adjust the intercom sensitivity to activate this background audio mode. Level
1 has the lowest sensitivity and level 5 has the highest sensitivity.
Note: If your voice is not louder than the sensitivity of the selected
level, the overlaid audio will not be lowered.
Audio Overlay Volume Management (Default: Disable)
The music, FM radio, and GPS overlaid audio reduces in volume whenever there
is an ongoing intercom conversation. If Audio Overlay Volume Management is
enabled, the volume level of the overlaid audio will not be reduced during an
intercom conversation.
HD Intercom (Default: Enable)
HD Intercom enhances the two-way intercom audio from normal quality to HD
quality. HD Intercom will become temporarily disabled when you enter into a
multi-way intercom. If this feature is disabled, the two-way intercom audio
will change to normal quality.
Note:
- The intercom distance of HD Intercom is relatively shorter than that of normal intercom.
- HD Intercom will become disabled temporarily when Bluetooth Intercom Audio Multitasking is enabled.
HD Voice (Default: Enable)
-
HD Voice allows you to communicate in high-definition during phone calls. This feature increases the quality so that the audio will be crisp and clear during phone call conversations.
-
If this feature is enabled, incoming phone calls will interrupt intercom conversations and audio from the SR10 will not be heard during intercom conversations. Three-Way Conference Phone Call with Intercom Participant will not be available if HD Voice is enabled.
Note: -
- Refer to the manufacturer of your Bluetooth device that will be connected to the headset to see if it supports HD Voice.
- HD Voice is active only when Bluetooth Intercom Audio Multitasking is disabled.
- Refer to the manufacturer of your Bluetooth device that will be connected to the headset to see if it supports HD Voice.
Smart Volume Control (Default: Disable)
Enabling Smart Volume Control automatically changes the level of the speaker
volume based on the level of the environment noise. You can enable it by
setting the sensitivity to low, medium, or high.
Sidetone (Default: Disable)
Sidetone is audible feedback of your own voice. It helps you to naturally
speak at the correct level according to varying helmet noise conditions. If
this feature is enabled, you can hear what you are speaking during an intercom
conversation or a phone call.
Voice Prompt (Default: Enable)
You can disable voice prompts by software configuration settings, but the
following voice prompts are always on.
Headset configuration settings menu, battery level indicator, speed dial, FM
radio functions
RDS AF Setting (Default: Disable)
Radio Data System (RDS) Alternative Frequency (AF) Setting allows a receiver
to re-tune to the second frequency location when the first signal becomes too
weak. With RDS AF enabled on the receiver, a radio station with more than one
frequency can be used.
FM Station Guide (Default: Enable)
When FM Station Guide is enabled, FM station frequencies are given by voice
prompts as you select preset stations. When FM Station Guide is disabled, the
voice prompts on FM station frequencies will not be given as you select preset
stations.
Advanced Noise Control™ (Default: Enable)
When Advanced Noise Control is enabled, the background noise is reduced during
an intercom conversation. When it is disabled, the background noise is mixed
with your voice during intercom.
TROUBLESHOOTING
SC2 Factory Reset
To erase all of your settings and start fresh, the headset can be restored to
factory default settings using the Factory Reset feature.
SC2 Remote Control Factory Reset
To erase all of your settings and start fresh, the SC2 Remote Control can be
restored to factory default settings using the Factory Reset feature.
Remote Control Pairing
- The SC2 and the SC2 Remote Control come paired together.
- They will automatically connect to each other when the SC2 and the SC2 Remote Control are powered on.
- If you are using a SC2 Remote Control other than the one included in the package, follow the procedure below to pair the SC2 and the SC2 Remote Control.
- On the SC2, press and hold the Multi-function Button for 5 seconds.
2. On your SC2 Remote Control, press and hold the (+) Button for 8 seconds to enter Bluetooth-pairing mode.
3. The SC2 will automatically perform pairing with the SC2 Remote Control in pairing mode.
SC2 Fault Reset
When the headset is not working properly, you can easily reset the unit.
-
Remove the installed SC2 from the helmet by lifting it up with the SC2 Remote Control cover.
-
Pull the antenna cable retainer out from its original position, and pull out the connected cables from the upper gap in the space.
Note: You can reset the SC2 without disconnecting the cables from the helmet.
- Locate the Pinhole Fault Reset Button on the back of the SC2.
- Gently insert a paperclip into the hole and tap the Pinhole Fault Reset Button with light pressure.
- The headset will shut down.
Note: Fault Reset will not restore the headset to factory default settings.
ABOUT COMPANY
- Producer: Sena Technologies Co., Ltd. 19, Heolleung-ro 569-gil, Gangnam-gu Seoul 06376, Republic of Korea
- Importer in Europe : SCHUBERTH GmbH Stegelitzer Straße 12 D-39126 Magdeburg, Germany
- Importer in US: SCHUBERTH North America 9920 Pacific Heights Blvd., Suite 150 San Diego, CA 92121