RAC213B Mostelado Alarm Clock Radio Instruction Manual

: June 1, 2024
: RAC

Table of Contents

RAC213B Mostelado Alarm Clock Radio
Product Usage Instructions
LOCATION OF CONTROLS
SPECIFICATIONS
Frequently Asked Questions
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

RAC213B Mostelado Alarm Clock Radio

Specifications

FM range: 87.5 to 108 MHz
Power supply: ~ 230V / 50 Hz
Power: 4W
Batteries: 9V DC

Product Usage Instructions

Power Switch and Connections
The power switch is on a separate circuit, switching it to OFF does not disconnect the entire device from power. Before use, ensure all connections are properly made.

Battery Usage
When inserting batteries, ensure correct polarity. Do not mix old and new batteries. If the device will not be used for an extended period (over a month), remove the batteries to prevent leakage.

Setting Current Time
1) Press and hold the TIME/PRESET/MEM (4) button throughout the setting process. 2) Use the HOUR/TUNE (5) button to set the hour and the MIN/TUNE+SET (6) button to display the time. 3) Release the TIME/PRESET/MEM (4) button after setting.

Setting Alarm Time
1) Press and hold the AL1/VOL- SET (2) button throughout the setting process. 2) Use the HOUR/TUNE (5) button to set the hour and the MIN/TUNE+SET (6) button to display the time. 3) Release the AL1/VOL- SET Button (2) after setting. 4) To verify the alarm time setting, press the AL1/VOL- SET Button (2).

Waking Up to Alarm Sound
1) Set the alarm time as described above. 2) Press the AL1/VOL (2) button to enter alarm settings, select BUZZ or RADIO function (RA- radio /BZ-BUZZ will appear on the display). Set AL2 similar to AL1.

Snooze/Sleep Function
1) When the alarm activates, pressing the SNOOZE/SLEEP button will stop the alarm for about 9 minutes before it resumes. 2) In standby mode, press the SNOOZE/SLEEP button to turn on the radio and then use MEM SET (4).

PowerSupply
Before connecting the radio independently to the power supply, read the following information. Power supply from electrical network only at a voltage of 230V-50Hz – AC. The device is designed to operate only with 230V~50Hz power supply. Connecting to a network with different parameters may damage the device.

WARNINGS

LOCATION OF CONTROLS

FUNCTION Selector (ON/OFF/AL/OFF)
AL1 VOL – SET Button
AL2 VOL – SET Button
TIME SET Button/MEM SET Button
HOUR/TUNE – SET Button
MIN/TUNE – SET Button
SNOOZE/SLEEP – SET Button
LED Clock Display
SPEAKER

POWER SUPPLY
This unit operates from a main supply of 230V ~ 50Hz. Connect the AC power cord to the AC household main outlet. Ensure that the voltage is as indicated on the rating plate on the rear of the unit.

BATTERY BACKUP POWER FAILURE PROTECTION
This radio has a battery backup circuit that will keep the correct time and alarm settings in the event of a temporary power interruption. Install a 9-volt battery (type 6F 22/006P), not included, into the battery compartment located on the bottom of the unit.

Note: We recommend an alkaline battery for longer usable life. Change the battery every 9 to 12 months for the best result and avoid possible battery leakage.
If power is temporarily interrupted the display will go blink and the radio will not play. However, the battery backup circuit will continue to maintain the clock and alarm settings. When power is restored the clock will display the correct time and alarm settings, and no adjustment is necessary.
Note: If power is interrupted and there is no battery in the compartment or the battery is exhausted. The time and alarm settings will be lost. When power is restored the clock will begin to flash indicating that the time and alarm settings must be corrected.

SETTING THE CORRECT TIME

Long press and hold the TIME/PRESET/MEM SET Button(4)
Press the HOUR/TUNE- SET Button (5) to advance the hour press. MIN/TUNE+ SET Button (6) until the correct time is displayed. Your Clock Radio uses a 24-hour clock.
Release the TIME/PRESET/MEM SET Button (4).

SETTING THE WAKEUP TIME

Long press and hold the AL1/VOL- SET Button(1)
Press the HOUR/TUNE- SET Button (5) to advance the hour press. MIN/TUNE+ SET Button (6) until the correct time is displayed Your Clock Radio uses a 24-hour clock.
Release the AL1/VOL- SET Button. (1).
To check the correct alarm time is set , press the AL1/VOL- SET Button. (1) AL2 with the 2.3 and the 2.4 operation

WAKE TO BUZZER ALARM

Set the alarm time as shown above.
Short press the AL1/VOL- SET Button (1) to open the alarm, and select a BUZZ or a radio (RA- radio/BZ-BUZZ, corresponding instructions exhibit of lanterns lit). AL2 provided with AL1.
LISTENING TO THE RADIO
Long press the MIN/TUNE+ SET Button(6) fast into the number of tuning.
Short press MIN/TUNE+ SET BUTTON (6) step number tuning.
Press HOUR/TUNE- SET BUTTON (5) fast reciprocal selection such as tuning.
Short press HOUR/TUNE- SET BUTTON (5) step number tuning.
Long press TIME/PRESET/MEM SET BUTTON to enter the storage station, with the MIN/TUNE + SET BUTTON (6) and HOUR/TUNE – SET BUTTON (5).
Pre-existing units, according to TIME/PRESET/MEM SET BUTTON (4) can be direct to existing radio.

SNOOZE/SLEEP FUNCTION

When the alarm sounds, pressing the SNOOZE/SLEEP Button will temporarily stop for about 9 minutes then the alarm sounds again.
The standby state presses the SNOOZE/SLEEP Button to turn on the radio then can choose the radio’s automatic shutdown time, followed by 120,90,60,30,15 minutes, and off.
If InIfhean alarm sounds,press the AL key AL.OFF o andr the corresponding can be closed when the alar If no operation , the alarm clockringsg for 30 minutesand will automatically stop.

CARE AND MAINTENANCE
To prevent fire or shock hazards, do not allow this clock radio to be exposed to rain or moisture. This clock radio should not be exposed to direct sunlight, very high or low temperature, moisture, or vibration, or placed in a dusty environment.
Do not use abrasives, benzine, thinners, or other solvents to clean the surfaces of the clock radio. To clean it, wipe with a mild non-abrasive detergent solution on a clean soft cloth. Never attempt to Insert wires, pins, or other objects into the ventilation holes or openings on the clock radio.

Note: When setting the Clock or Alarm times remember that this clock radio has a 24 Hour clock.

AC POWER
For your own solely read the following instructions carefully before attempting to connect this clock radio to the mains.
Mains Supply 230V-50Hz – AC only.
This unit is designed to operate on a 230V~50Hz supply only. Connecting it to other power sources may damage it, Ensure

SPECIFICATIONS

FM Band: 87,5 to 108 MHz
Power Supply: ~ 230V / 50 Hz
Power Consumption: 4 W
Standby Power Consumption: < 1 W
9V DC BATTERY

WE RESERVE THE RIGHT TO CHANGE TECHNICAL SPECIFICATIONS.
WARNING: DO NOT USE THIS PRODUCT NEAR WA TER, OR IN WET AREAS TO AVOID FIRE INJFROMROMF THE ELECTRIC CURRENT. ALWAYS TURN OFF THE PRODUCT WHEN YOU DON’T USE IT OR BEFORE A REVISION. THERE AREN’T ANY PARTS IN THIS APPLIANCE WHICH ARE REPARABLE BY CONSUMER. ALWAYS APPEAL TO A QUALIFIED AUTHORIZED SERVICE. THE PRODUCT IS UNDER A DANGEROUS TENTION.

TO AVOID THE DANGER OF SUFFOCATION, KEEP PLASTIC BAGS AWAY FROM BABIES AND CHILDREN. DO NOT USE THIS BAG IN CRIBS, BEDS, CARRIAGES OR PLAYPENS. THIS BAG IS NOT A TOY.

Disposal of old Electrical & Electronic Equipment (Applicable in the European Union and other European countries with separate collection systems)
This symbol on the product or its packaging indicates that this product shall not be treated as household waste. Instead, it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of the product. The recycling of materials will help to conserve natural resources. For more detailed information about recycling this product, please contact your local Civic Office, your household waste disposal service, or the shop where you purchased the product.

Hereby, ETA a.s. declares that the radio equipment type RAC213 complies with Directive 2014/53/EU.
The full text of the EU Declaration of Conformity is available at the following internet address: http://www.hyundai- electronics.cz/declaration_of_conformity

Licensed by Hyundai Corporation Holdings, Korea

Frequently Asked Questions

Q: What do the warning signs in the manual indicate?
- A: The warning signs indicate important instructions and dangerous voltage within the unit, emphasizing safety precautions for users.
Q: Can old and new batteries be mixed in the device?
- A: No, it is recommended not to mix old and new batteries in the device to ensure proper functionality.
Q: What should be done if the device will not be used for an extended period?
- A: If the device will not be used for over a month, remove the batteries to prevent potential leakage.