cameo G4FC RGBL LED Gallery Light User Manual

cameo G4FC RGBL LED Gallery Light

Product Information

gallery lighting with RGBL LED.
Website| CAMEOLIGHT.COM

Product Usage Instructions

1. Read the user manual carefully before using the product.
2. Make sure the product is suitable for indoor installation.
3. Ensure the device is connected to a suitable power source.
4. Maintain a minimum distance to illuminated surfaces as specified in the technical data.
5. Avoid placing the product near flammable materials.
6. Mount the product securely according to the provided instructions.
7. If applicable, fit the directional grille, diffuser, and filter.
8. Refer to the optional accessories section for additional features.
9. Follow the care, maintenance, and repair instructions to ensure optimal performance.
10. Dispose of the product responsibly according to local regulations.

INSTRUCTION

You have made the right choice!
This device has been developed and manufactured to the highest quality standards to ensure many years of problem-free operation. Please read this user manual carefully to be able to use your new Cameo product quickly and optimally. Further information about Cameo Light is available on our website CAMEOLIGHT.COM.

INFORMATION ON THIS USER MANUAL

• Carefully read the safety instructions and the entire manual before operating the device.
• Observe the warnings on the device and in the user manual.
• Always keep the user manual within reach.
• If you sell or pass on the device, it is important that you also include this user manual, as it is an integral part of the product.

INTENDED USE

• This product is a spotlight for permanent installation!
• This spotlight is intended exclusively for professional users and is not suitable for private households or third parties!
• Use of the product outside the specified technical data and operating conditions, as well as incorrect installation, is considered inappropriate!
• Liability for damage and third-party damage to persons and property due to inappropriate use is excluded!

The product is not suitable for:

• Use by persons (including children) with limited physical, sensory or mental abilities or lack of experience and knowledge.
• Children (children must be instructed not to play with the device).

DEFINITIONS AND SYMBOL EXPLANATIONS

1. DANGER: The word DANGER, possibly in combination with a symbol, indicates immediately dangerous situations or conditions for life and limb.
2. WARNING: The word WARNING, possibly in combination with a symbol, indicates potentially dangerous situations or conditions for life and limb.
3. CAUTION: The word CAUTION, possibly in combination with a symbol, is used to indicate situa-tions or conditions that may lead to injury.
4. ATTENTION: The word ATTENTION, possibly in combination with a symbol, refers to situations or states that can lead to damage to property and/or the environment.
5. CAUTION: This symbol identifies hazards that can cause electric shock.
   • This symbol identifies hazardous areas or hazardous situations.
   • This symbol indicates hazards caused by hot surfaces.
   • This symbol indicates hazards caused by intense light sources.
   • This symbol indicates a device in which there are no user-replaceable parts.
   • This symbol indicates additional information on the operation of the product.
   • This symbol indicates a device that may only be used in dry rooms.

SAFETY INSTRUCTIONS

HAZARD

1. Do not open or modify the unit.
2. If your device no longer functions properly, if liquids or objects get inside it, or if it has been damaged in any other way, switch it off immediately and disconnect it from the mains. The device may be repaired only by authorized repair technicians.
3. For devices of protection class 1, the protective conductor must be connected correctly. Never disconnect the protective conductor. Devices of protection class 2 do not have a protective conductor.
4. Ensure that live cables are not kinked or otherwise mechanically damaged.
5. Never bypass the appliance fuse.

WARNING

1. The device may not be operated if it shows obvious signs of damage.
2. The device may only be installed in a voltage-free state.
3. If the mains cable of the device is damaged, do not operate the device.
4. Permanently connected power cables may only be replaced by a qualified person.

ATTENTION

1. Do not operate the unit if it has been exposed to large temperature fluctuations (for example, after transport). Moisture and condensation can damage the device. Switch on the device only when it has reached room temperature.
2. Make sure that the voltage and frequency of the main supply correspond to the values indicated on the unit. If the device has a voltage selector switch, do not connect the device until it has been set correctly. Use only suitable power cables.
3. To disconnect the unit from the mains at all poles, it is not sufficient to press the on/off switch on the unit.
4. Make sure that the fuse used corresponds to the type printed on the unit.
5. Make sure that appropriate measures have been taken against overvoltage (e.g. lightning strike).
6. Observe the specified maximum output current on units with a power-out connection. Ensure that the total current consumption of all connected devices does not exceed the specified value.
7. Replace pluggable mains cables only with the original cables.

HAZARD

1. The danger of suffocation! Plastic bags and small parts must be kept out of reach of persons (including children) with reduced physical, sensory, or mental capabilities.
2. Danger from falling down! Make sure that the device is securely installed and will not fall down. Only use suitable stands or mounts (particularly for fixed installations). Ensure that accessories are properly installed and secured. Ensure that applicable safety regulations are observed.

WARNING

1. Use the device only in the manner intended.
2. Operate the device only with the accessories recommended and intended by the manufacturer.
3. During installation, observe the safety regulations applicable in your country.
4. After connecting the unit, check all cable routes to avoid damage or accidents, e.g. due to tripping hazards.
5. Always observe the specified minimum distance to normally flammable materials! Unless explicitly stated, the minimum distance is 0.3 m.
6. Always observe the minimum distance to the illuminated surface that can be read on the device!

CAUTION

1. In the case of moving components such as mounting brackets or other moving components, there is a possibility of jamming.
2. In the case of units with motor-driven components, there is a risk of injury from the movement of the unit. Sudden movement of the device can cause shock reactions.
3. The housing surface of the device can become very hot during regular operation. Ensure that accidental touching of the housing is not possible. Always allow the lamp to cool sufficiently before removal, maintenance work charging, etc.

ATTENTION

1. Do not install or operate the device near any radiators, heat registers, stoves, or other heat sources. Ensure that the device is always installed in such a way that it is sufficiently cooled and cannot overheat.
2. Do not place ignition sources such as burning candles near the device.
3. Ventilation openings must not be covered and fans must not be blocked.
4. Use the original packaging or packaging provided by the manufacturer for transport.
5. Avoid shock or impact on the unit.
6. Observe the IP protection class as well as the ambient conditions such as temperature and humidity according to the specification.
7. Devices can be constantly further developed. In the event of deviating information on operating conditions, performance, or other device properties between the user manual and the device labeling, the information on the device always takes priority.
8. The unit is not suitable for tropical climates and for operation above 2000 m above sea level.
9. Unless explicitly stated, the unit is not suitable for operation in marine conditions.

INFO: For conversion or retrofit sets or accessories provided by the manufacturer, it is essential to observe the instructions included.

CAUTION: IMPORTANT INFORMATION REGARDING LIGHTING PRODUCTS!

1. Never look directly into the beam of light, not even for a short period of time.
2. Never look into the beam of light using optical devices such as a magnifying glass.
3. Stroboscopic effects may cause epileptic seizures in susceptible individuals!
4. Permanently installed lamps are built into these lighting units. These may not be replaced by the user. The lamps contained in this lighting unit may only be replaced by the manufacturer, its service partner, or a similarly qualified person.

SIGNAL TRANSMISSION BY RADIO (e.g. W-DMX or audio radio systems):

• The quality and performance of wireless signal transmissions generally depend on the ambient conditions. The following factors can impact range and signal stability, for example:
• Shielding (e.g. masonry, metal structures, water)
• The high volume of radio traffic (e.g. powerful wireless LAN networks) Interference
• Electromagnetic radiation (e.g. LED video screens, dimmers)

All range specifications refer to free-field applications with visual contact and without interference!
The operation of transmission systems is subject to official regulations. These may vary from region to region and must be checked by the operator before use (e.g. radio frequency and transmission power).

WARNING: Devices with wireless signal transmission are not suitable for use in sensitive areas in which radio operation can lead to potential detrimental effects. These include:

• Hospitals, health centres or other healthcare facilities that provide patient treat-ment with skilled personnel and equipment.
• Hazardous areas Class I, II and III
• Restricted areas
• Military facilities
• Aircraft or vehicles
• Areas where the use of mobile phones is prohibited

TRANSMISSION VIA W-DMX
WARNING: In general, wireless DMX transmission must not be used for applications involving safety-related factors that might result in personal injury or property dama-ge in the event of a failure.
This applies in particular to moving scene or traverse structures, DMX- controlled motors/lifts, or lifting devices for operating DMX-operated platform lifts, hydraulic systems or comparable moving components.
Furthermore, wireless DMX transmission must not be used to trigger flame or pyro-technic devices, explosion-driven effects, or to control gas or liquid effects. These include CO2 cannons, confetti shooters, water effects, or similar.

AMBIENT TEMPERATURE
Please observe the maximum ambient temperature in operation specified in the technical data. A special protection circuit in the headlamp ensures that the brightness is reduced if the ambient temperature is too high to protect the unit components. If you notice a significant loss of brightness in the headlamp, please check the ambient temperature in the direct vicinity of the headlamp and, if necessary, ensure that the temperature is brought to or below the maximum permitted value.

INSTRUCTIONS FOR INDOOR INSTALLATION EQUIPMENT

1. Equipment for installation applications is designed for continuous operation.
2. Equipment for indoor installation is not weather-resistant.
3. Surfaces and plastic parts can also age in installation equipment, e.g. due to UV irradiation and temperature fluctuations. This generally does not impair functionality.
4. With permanently installed devices, the accumulation of impurities, e.g. dust, is to be expected. Always observe the care instructions.
5. Unless explicitly stated otherwise on the device or in the technical data, the devices are intended for installation heights of less than 5 m.

INCLUDED

Remove the product from the packaging and remove all packaging material. Please check the completeness and integrity of the delivery and notify your distribution partner immediately after purchase if the delivery is not complete or if it is damaged.
Included in the scope of delivery of the product CLG4FC are:

• 1 x Cameo G4FC Spotlight, black
• User manual

The scope of delivery of the product CLG4FCWH includes:

• 1 x Cameo G4FCWH Spotlight, white
• User manual

INTRODUCTION

• LED Gallery Light with one 40 W RGBL LED
• CLG4FC (black housing)
• CLG4FCWH (white housing)
• CONTROL FUNCTIONS
• 1CH, 2CH 16 bit, 3CH CCT, 3CH Presets, 4CH Direct, 5CH HSI,
• 8CH Direct + CCT and 12CH 16 Bit Full Access DMX Control
• W-DMX™ Standalone function (set up via Cameo Unicon)

FEATURES

Compatible with GLOBAL pro (formerly NOKIA) XTS, XTTS, and XTSC 3-phase tracks. 40 W RGBL LED. W-DMX™. DMX512. RJ45-Anschluss. Operating voltage: 100–240 V AC. Diffusing screens, filters and straightening grids are optionally available.

The spotlight features the RDM standard (Remote Device Management). This remote device management enables the status query and configuration of RDM end devices via an RDM-capable controller, such as the optionally available Cameo UNICON (item number CLIREMOTE).
The Cameo UNICON also allows access to the entire fixture menu.

CONNECTIONS, OPERATING AND DISPLAY ELEMENTS

RAIL ADAPTER
Rail adapter for mounting on a compatible 3-phase rail.

TILTABLE AND SWIVELLING SUPPORT ARM
Support arm with two joints for adjusting the beam direction on the horizontal and vertical plane.

RJ45 INTERFACE
Interface for configuring and controlling the fixture using the Cameo UNICON DMX/RDM controller. The fixture can also be configured using another RDM controller and controlled using a standard DMX controller.
Pin assignment:

W-DMX RESET BUTTON
Button for disconnecting W-DMX connections and for pairing the spotlight with W-DMX devices. The housing surface of the device can become very hot during regular operation. Always allow the unit to cool down sufficiently before operating the button. Activate the fixture’s W-DMX receiver via Cameo UNICON and reset the receiver by pressing the button for about 3 seconds. All previous connections are disconnected and the receiver is put into pairing standby for about 1 minute, the status LED no. 5 flashes red quickly. The receiver is now waiting for a transmitter pairing request. Start the pairing process on the transmitter; the pairing occurs automatically. In the same way, several receivers can be paired to a transmitter either simultaneously or one after the other. A W-DMX connection is always maintained until the connection is disconnected by means of the Reset command in the receiver or the Unlink command in the transmitter, regardless of whether a device has been disconnected from the power supply in the meantime.

STATUS LED
The LED shows the current status of the spotlight when controlled via cable and W-DMX.

OPERATION PER UNIT CONTROLLER CAMEO UNICON (optionally available)

After you have switched on the Unit Controller UNICON (briefly press BACK to switch on), “Update, Please Wait” (for service purposes only) appears in the display for a short time and then the main menu. Connect the remote unit to the Gallery Light G4 FC via network cable and connect the spotlight to the power supply.

Select the menu item RDM/Fixture and confirm the selection. Now the system searches for connected RDM devices (Discovery) and if the G4 FC is correctly connected and switched on,
a device is found (Discovered: 1). After a short time, the G4 FC is displayed as the only unit in a list (the first part of the displayed RDM unit shows the unit model, the second part behind “/” is the label and can be individually adjusted in the menu item Label for easier identification). Now confirm to enter the submenu.

All information and configuration options for the spotlight that can be called up and edited via RDM are now displayed.

List of information and configuration options with explanations:

LABEL: In the RDM/Fixture menu, select Label and confirm the selection to individually name the RDM device.

DEVICE MENU (Fixture Menu):
In the RDM/Fixture menu, select Fixture Menu and confirm the selection.

CONFIGURE DMX START ADDRESS
Select DMX Address, confirm the selection, set the desired DMX address, and confirm the entry. (The highest value depends on the currently activated DMX operating mode)

SELECT DMX MODE
Select DMX Mode, confirm the selection, then select the desired DMX mode and confirm the selection.

AUTO STANDALONE MODE
The 6 available auto-programs each comprise non-editable color-change sequences. Brightness (Dimmer) and running speed (Speed) are separately adjustable in each program.
Select Stand Alone, confirm the selection, then select Auto and confirm again. Now select the desired program (Program 1 – Program 6) and confirm again. Now select Dimmer or Speed, confirm, and set the brightness or speed value from 001 to 100 as desired. Confirm all entries.

STATIC STANDALONE MODE
The Static standalone mode allows the Dimmer, Dimmer Fine, Strobe and RGBAL values to be set directly on the device with values between 000 and 255, in a similar way to with a DMX controller. In this way, an individual scene can be created without an additional DMX controller.

Select Stand Alone, confirm the selection, then select Static and confirm again. Now select the menu item you wish to edit and confirm the selection. In the selected menu item, set the desired value from 000 to 255 and confirm the entry. The values for the strobe effect correspond to the values in channel 2 of the DMX table 3 CH presets.

STANDALONE MODE COLOR MACRO
15 different color macros and 4 individual colors (User Color 1-4) are available as presets. The brightness can be adjusted for each preset.

Select Stand Alone, confirm the selection, then select Color Macro and confirm again. Select the desired color preset and confirm (Color Off = blackout). The brightness of the selected preset can now be adjusted from 000 to 100. Confirm all entries.

The individual colors User Color 1-4 are created in the menu item Edit User Color in the Stand Alone menu.

STANDALONE MODE TUNEABLE WHITE
In the standalone mode Tuneable White, the color temperature (CCT) can be adjusted from 1800 K to 6500 K in 100 K increments, in addition to the brightness (Dimmer) and color (Tint).
Select Stand Alone, confirm the selection, then select Tunable White and confirm again. Now select the menu item you wish to edit and confirm the selection. Set the desired value and confirm the entry.

STAND-ALONE CATEGORY EDIT USER COLOUR

• In the stand-alone category Edit User Color, you have the option of saving brightness (Dimmer and Dimmer Fine), stroboscope (Strobe), and a color mix of R, G, B, and L directly in the unit in four individual colors presets.
• Select Stand Alone, confirm the selection, then select Edit User Color and confirm again. Select the desired preset (Color 1 – Color 4) and confirm the selection. Now select the menu item you wish to edit and confirm. Set the desired value from 000 to 255 and confirm again. The values for the strobe effect correspond to the values in channel 2 of the DMX table 3 CH presets.

TIMER FUNCTION
The timer function allows the standalone modes Static, Color Macro, and Tuneable White to be timer controlled in such a way that the Fade In time can be configured from 0.5 seconds to 24 hours, the Dwell Time from 0.5 seconds to 24 hours, and infinite (Limitless) and the Fade Out time from 0.5 seconds to 24 hours. After activation of the timer function, the timer control will be implemented upon the next system start.

Select Stand Alone, confirm the selection, then select Timer and confirm again. Under Switch, select the setting On and confirm. For the individual timer control settings, select Fade In, Dwell Time or Fade Out and confirm. You can now set the respective value as desired. Confirm all entries. To deactivate the timer function, under point Switch, select the setting Off and confirm.

SYSTEM SETTINGS (Settings)
Select Settings and confirm.

This will take you to the submenu for configuring the submenu items (see table):

SYSTEM INFORMATION (SysInformation)
Starting from the main display, press the encoder to enter the main menu. Select the menu item SysInformation and confirm the selection.

This will take you to the submenu for accessing the system information (see table):

MOUNTING

• HAZARD: Overhead mounting requires extensive experience, including the calculation of the load limit values of the installation material and regular safety inspection of all installation materials and spotlights. If you do not have these qualifications, do not attempt to perform an installation yourself. Refer instead to a qualified professional. There is a risk that devices that are incorrectly mounted and secured may come loose and fall down. This can cause serious injury or death.
• DANGER: Only use the spotlight for horizontally mounted rails (horizontal ceiling mounting)! The spotlight is not suitable for inclined rails and wall mounting!
• WARNING: Before mounting or dismounting, make sure that no electrical voltage is applied to the 3-phase rail (switch off fuses)!
• ATTENTION: The spotlight is not suitable for use with external dimmers!

Use the knurled wheel A to set to phases 1, 2, or 3 (see the window below the knurled wheel; 0 = off). The adjustment can be made before or after mounting on a rail.
To mount on a rail, open the locking lever B of the rail adapter (lever in open position in the illustration) and then press the adapter into the rail until it lies flat on the rail edges (Fig. 1).
Secure the connection by closing the locking lever again (Fig. 2).

To dismantle the headlamp, open the locking lever (fig. 3) and pull the headlamp downwards out of the rail (fig. 4).

FITTING THE DIRECTIONAL GRILLE, DIFFUSER AND FILTER
Up to three optionally available accessories can be mounted in combination in front of the headlamp’s exit lens (see OPTIONAL ACCESSORIES).
Remove the end ring held by strong magnets from the headlamp (fig. A) and then remove the retaining ring, also held by magnets, from the end ring (fig. B). Now place the desired accessories (in example C, first the straightening grid, then a diffusing disc, and then a CTO filter) in the end ring and then place the retaining ring on the accessories in the end ring. Which of the three possible positions the retaining ring is placed in depends on the total height of the inserted accessories.

Now place the end ring including accessories on the lamp as shown in figure D.

OPTIONAL ACCESSORIES

Filter

• CLG4CTB (CTB Filter)
• CLG4CTO (CTO filter)

Diffusers

• CLG46010LENS (60° x 10°)
• CLG410LENS (10°)
• CLG420LENS (20°)
• CLG430LENS (30°)
• CLG460LENS (60°)

Straightening grids

• CLG4HC (Honeycomb, black)
• CLG4HCWH (Honeycomb, white)

CARE, MAINTENANCE, AND REPAIR

• In order to ensure the long-term, proper functioning of the device, it must be regularly cleaned and, if necessary, maintained. The maintenance requirement depends on the intensity of use and the environment in which it is used.
• We generally recommend a visual inspection before each operation. Furthermore, we recommend carrying out all the applicable maintenance measures specified below once every 500 operating hours or, in the case of a lower intensity of use, at the latest after one year. Warranty claims may be limited in the event of defects resulting from inadequate maintenance.

CARE (carried out by user)

WARNING! Before carrying out any care or maintenance, the power supply – and, if possible, all device connections – must be disconnected.
PLEASE NOTE! Improper care can lead to impairment of the device or even its destruction.

1. Housing surfaces must be cleaned with a clean, damp cloth. Make sure that no moisture can penetrate the device.
2. Air inlets and outlets must be regularly cleaned of dust and dirt. If compressed air is used, make sure that damage to the device is prevented (e.g. fans must be blocked in this case).
3. Lines and plug contacts must be cleaned regularly and dust and dirt must be removed.
4. In general, no cleaning agents or abrasive agents may be used, otherwise, the surface finish may be damaged.
5. Devices must generally be stored dry and protected from dust and dirt.

MAINTENANCE AND REPAIR (by qualified personnel only)

• HAZARD! There are live components in the device. Even after disconnecting the mains connection, there may still be residual voltage in the device, for example, due to charged capacitors.
• PLEASE NOTE! There are no user-serviceable assemblies in the device.
• PLEASE NOTE! Maintenance and repair work may only be carried out by qualified specialist personnel authorized by the manufacturer. If in doubt, consult the manufacturer.
• PLEASE NOTE! Improperly performed maintenance work may affect the warranty claim.

DIMENSIONS (mm)

TECHNICAL DATA

MINIMUM DISTANCE TO ILLUMINATED SURFACE

This symbol with distance specification in meters (m) indicates the minimum distance between the light head and the illuminated surface. In this example, the distance is 0.5 m. Please refer to the technical data in this manual and the imprint on the unit casing for the value valid for this unit!

MINIMUM DISTANCE TO NORMALLY FLAMMABLE MATERIALS

This symbol with distance specification in meters (m) indicates the minimum distance between the light head and normally flammable materials. In this example, the distance is 0.5 m. Please refer to the technical data in this manual for the value valid for this unit!

DISPOSAL

PACKAGING

1. Packaging can be fed into the reusable material cycle using the usual disposal methods.
2. Please separate the packaging in accordance with the disposal laws and recycling regulations in your country.

DEVICE

1. This appliance is subject to the European Directive on Waste Electrical and Electronic Equipment as amended. WEEE Directive Waste Electrical and Electronic Equipment. Old appliances do not belong in household waste. The old device must be disposed of via an approved disposal company or a municipal disposal facility. Please observe the applicable regulations in your country!
2. Observe all disposal laws and regulations applicable in your country.
3. As a private customer, you can obtain information on environmentally friendly disposal options from the seller of the product or the appropriate regional authorities.

MANUFACTURER’S DECLARATIONS

Manufacturer’s warranty & limitation of liability Adam Hall GmbH, Adam-Hall- Str. 1, D-61267 Neu-Anspach
E-Mail Info@adamhall.com / +49 (0)6081 / 9419-0

Our current warranty conditions and limitation of liability can be found at: https://cdn-shop.adamhall.com/media/pdf/Manufacturers-Declarations- CAMEO_DE_EN_ES_FR.
pdf In case of service, please contact your sales partner.

CE conformity
Adam Hall GmbH hereby confirms that this product meets the following guidelines (where applicable):

• Low-Voltage Directive (2014/35/EU)
• EMC Directive (2014/30/EU)
• RoHS (2011/65/EU)
• RED (2014/53/EU)

EC Declaration of Conformity

• Declarations of conformity for products subject to the LVD, EMC, and RoHS Directive can be requested from info@adamhall.com
• Declarations of conformity for products subject to RED can be downloaded from www.adamhall.com/compliance/
• Subject to misprints and errors, as well as technical or other modifications.

References

• Downloads | Service | Adam Hall Shop
• Cameo® | For Lumen Beings
• Downloads | Service | Adam Hall Shop

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>