BORMANN PRO BCD3200 Electric Vacuum Tile Suction Instruction Manual

BORMANN PRO BCD3200 Electric Vacuum Tile Suction

Product Information

Specifications

• Model: BCD3200
• Voltage: 21 V
• Suction cup diameter: 128 mm
• Applicable ceramic tile: 128 cm
• Battery: 2 x 1.5 Ah
• Vibration frequency: 28000 r/min
• Adsorption capacity: 128 kg
• Weight: 1.6 kg
• Levers: 12

Safety Precautions

Please read the user manual and safety instructions carefully before use to ensure safe and satisfactory use of this product.

• Wear hearing protection!
• Wear a dust mask!
• Wear safety glasses!
• Charger safety Warning: To reduce the risk of electric shock and damage to the charger and battery, use the lithium batteries listed on the charger to charge the battery. Use of another type of battery can cause an explosion and cause injury.
• Doing so may damage the charger and cables and cause an electric shock. Replace cables immediately in the event of damage.
• Make sure that the wires are placed in a suitable position and do not touch the sharp edges and moving parts, otherwise they will be damaged. This will reduce the risk of damaging the wires and causing an electric shock.
• Keep the cable and charger away from high temperatures to prevent damage to the charger’s casing and internal parts.
• Do not allow gasoline, petroleum, etc. to come into contact with plastic parts. These substances contain chemicals that can damage, weaken, or destroy plastic.
• It is not necessary to use an extension cord. Using an unsuitable extension cable may cause fire or electric shock. If you must use an extension cable, make sure that the extension cable is in good condition and matches the charger socket.
• Do not use the charger with a damaged cord or socket, as this may cause a short circuit and electric shock. If damaged, return the charger to an authorized service center for repair.
• Do not use the charger if it has been dropped or otherwise damaged. Take the charger to an authorized service center to check that the charger is intact.
• Do not disassemble the charger without authorization. The charger should only be repaired by a qualified electrician. There is a high risk of electric shock and fire due to incorrect reorganization.
• Always unplug the charger from the wall outlet when servicing or cleaning the charger. This will reduce the risk of electric shock.
• Unplug the charger when it is not in use. This can reduce the risk of electric shock or prevent metal substances from falling into the socket and damaging the charger.
• Avoid electric shock. Do not touch uninsulated parts of the socket.
• WARNING! The machine may overheat after prolonged use and must be cooled to a suitable temperature before use to avoid damage to the machine.

Product Usage Instructions

To ensure safe and proper usage of the BCD3200, please follow these instructions:

Step 1: Preparation

Make sure you have all the necessary equipment and materials ready:

• BCD3200 machine
• Applicable ceramic tiles
• Safety glasses
• Hearing protection
• Dust mask
• Charger and lithium batteries listed in the user manual

Step 2: Safety Precautions

Before starting the operation, ensure the following safety precautions are taken:

• Wear safety glasses, hearing protection, and a dust mask to protect yourself from potential hazards.
• Keep the cables and charger away from high temperatures and flammable substances.
• Only use the charger with the specified lithium batteries to avoid the risk of explosion or injury.
• Inspect the charger and cables for any damage. If damaged, do not use and return to an authorized service center for repair.

Step 3: Operating the BCD3200

Follow these steps to operate the BCD3200:

1. Attach the appropriate suction cup to the machine based on the size of the ceramic tiles you will be working with.
2. Ensure the machine is turned off before inserting the battery.
3. Insert the lithium batteries into the machine following the instructions in the user manual.
4. Turn on the machine using the power switch.
5. Place the suction cup on the ceramic tile and press firmly to create a secure seal.
6. Adjust the levers to the desired position for easy handling and control.
7. Once in position, activate the machine by pressing the start button.
8. Move the machine along the ceramic tile surface, allowing the suction cup to hold it securely in place.
9. Continue the operation until the desired area is covered.
10. After use, turn off the machine and remove the suction cup from the ceramic tile.
11. Remove the battery from the machine and store it in a safe place.

SAFETY PRECAUTIONS

Please read the user manual and safety instructions carefully before use to ensure safe and satisfactory use of this product.

• Wear hearing protection!
• Wear a dust mask!
• Wear safety glasses!

Charger safety

Warning: To reduce the risk of electric shock and damage to the charger and battery, use the lithium batteries listed on the charger to charge the battery. Use of another type of battery can cause an explosion and cause injury.

1. Before using the charger, carefully read the operating instructions and the warnings on the instructions to avoid the risk of injury due to misuse.
2. Do not use the charger outdoors. Do not expose it to rain or moisture. The risk of electric shock is increased if water enters the machine.
3. Do not use this charger to charge batteries from other manufacturers. Failure to use the device according to the regulations may result in fire or explosion.
4. Do not use the charger outdoors, and keep it away from rain or moisture. The risk of electric shock is increased if water is allowed to penetrate the machine.
5. Do not misuse the charger or the cables. Do not pull the charger by the cord. Do not pull on the cord when disconnecting the charger from the power source. Doing so may damage the charger and cables and cause an electric shock. Replace cables immediately in the event of damage.
6. Make sure that the wires are placed in a suitable position and do not touch the sharp edges and moving parts, otherwise they will be damaged. This will reduce the risk of damaging the wires and causing an electric shock.
7. Keep the cable and charger away from high temperatures to prevent damage to the charger’s casing and internal parts.
8. Do not allow gasoline, petroleum, etc. to come into contact with plastic parts. These substances contain chemicals that can damage, weaken, or destroy plastic.
9. It is not necessary to use an extension cord. Using an unsuitable extension cable may cause fire or electric shock. If you must use an extension cable, make sure that the extension cable is in good condintion and matches the charger socket.
10. Do not use the charger with a damaged cord or socket, as this may cause a short circuit and electric shock. If damaged, return the charger to an authorised service centre for repair.
11. Do not use the charger if it has been dropped or otherwise damaged. Take the charger to an authorised service centre to check that the charger is intact.
12. Do not disassemble the charger without authorisation. The charger should only be repaired by a qualified electrician. There is a high risk of electric shock and fire due to incorrect reorganisation.
13. Always unplug the charger from the wall outlet when servicing or cleaning the charger. This will reduce the risk of electric shock.
14. Unplug the charger when it is not in use. This can reduce the risk of electric shock or prevent metal substances from falling into the socket and damaging the charger.
15. Avoid electric shock. Do not touch uninsulated parts of the socket.

WARNING:  The machine may overheat after prolonged use and must be cooled to a suitable temperature before use to avoid damage to the machine.

SPECIFICATIONS

Technical Data

Technical Data

Model| BCD3200
Voltage| 21 V
Suction cup diameter| 128 mm
Applicable ceramic tile| 128 cm
Battery| 2 x 1.5 Ah
Vibration frequency| 28000 r/min
Adsorption capacity| 128 kg
Weight| 1.6 kg
Levers| 12

• The manufacturer reserves the right to make minor changes to product design and technical specifications without prior notice unless these changes significantly affect the performance and safety of the products. The parts described / illustrated in the pages of the manual that you hold in your hands may also concern other models of the manufacturer’s product line with similar features and may not be included in the product you just acquired.
• To ensure the safety and reliability of the product and the warranty validity, all repair, inspection or replacement work, including maintenance and special adjustments, must only be carried out by technicians of the authorized service department of the manufacturer.
• Always use the product with the supplied equipment. Operation of the product with non-provided equipment may cause malfunctions or even serious injury or death. The manufacturer and the importer shall not be liable for injuries and damages resulting from the use of non-conforming equipment.

MAIN PARTS

1. Lithium battery
2. Non-slip rubber handle
3. Start key
4. Mode key
5. Auxiliary handle
6. Absorption lever
7. Alloy head shell
8. Suction cup

OPERATION

1. Install the battery pack according to the battery pack instructions.
2. Place the device on the tile to be laid and lock it forward. The level of the tiles is adjusted using the stepless speed change function of the switch.
3. Lock the pushbutton switch back to lay the tiles; lock the pull button forward to suction the tiles.

Charging instructions

• Switch off the battery pack and place it in a dedicated charger for charging. The charger will show a red light when charging and a green light when fully charged.
• Normal charging time is 2 hours.

Warning

1. There is no need to keep pressing the switch during the tiling process, rhythmic progress is more conducive to tiling.
2. The machine should be placed in a dry place to avoid contact with liquid.
3. Please remove the dirt on the surface of the machine in time after use.
4. Please charge in time when the battery is insufficient, and charge it once a month when not in use for a long time.
5. Do not place the battery pack in water or expose it to rain. A short circuit of the battery will cause a large current to overheat and may cause fire or even breakdown.

MAINTENANCE

Note: The battery must be removed before any maintenance work on the device.

1. Check the mounting screws. Always check that the mounting screws are securely fastened. Loosening screws can easily cause serious accidents.
2. Check the charger cable regularly. If any damage is found, entrust an authorized repair center to deal with it immediately.
3. Keep the ventilation slots clean and smooth. Always remove dust and oil, and prevent debris from entering.
4. Repairs must be performed by an authorized repair center. Only use original accessories and parts.
5. Clean regularly. Avoid using solvents that can cause plastic cracks to wipe plastic parts. A soft cloth slightly moistened with soapy water is recommended. Do not expose the motor to water, and it is forbidden to put the entire body into the water, so as to avoid motor failure and electric shock!

ENVIRONMENTAL DISPOSAL

In order to avoid damages on transportation, the tool has to be delivered in solid packaging. Packaging as well as the unit and accessories are made of recyclable materials and can be disposed accordingly. The tool’s plastics components are marked according to their material, which makes it possible to remove environmental friendly and differentiated because of available collection facilities.

Only for EU countries

Do not dispose of electric tools together with household waste material!
In observance of European Directive 2002/96/EC on waste electrical and electronic equipment and its implementation in accordance with national law, electric tools that have reached the end of their life must be collected separately and returned to an environmentally compatible recycling facility.

WARRANTY

The power tools have been manufactured according to strict standards, set by our company, which are aligned with the respective European quality standards. The power tools of our company are provided with a warranty period of 24 months for non-professional use, 12 months for professional use and 24 months for chargers and batteries. The warranty is valid from the date of purchase of the product. Proof of the warranty right is the purchase document of the tool (retail receipt or invoice). Under no circumstances shall the company cover the relevant cost of spare parts and respective required working hours unless a copy of the purchase document is presented. In case the repair has to be done by our service department the cost of transportation (to and from) is entirely borne by the sender (client). The tools must be sent for repair to the company or to an authorized workshop in the appropriate way and means of transport.

WARRANTY EXEMPTIONS AND RESTRICTIONS

1. Spare parts that wear out naturally as a consequence of being used (brushes, cables, switches, chargers, chucks etc.).
2. Tools damaged as a result of non-compliance with the instructions of the manufacturer.
3. Tools poorly maintained.
4. Use of improper lubricants or accessories.
5. Tools given to third entites free of charge.
6. Damage due to an electrical connection at a voltage other than that indicated on the appliance plate.
7. Connect on to a non-earthed power supply.
8. Change in current voltage.
9. Damage resulting from the use of salty water (e.g., washing machines, pumps).
10. Damage or malfunction resulting from improper cleaning procedure of the tool.
11. Contact of the tool with chemicals, or damage as a result of moisture or corrosion.
12. Tools that have been modifi ed or opened by unauthorized personnel.
13. Tools used for rent.

The warranty covers only the free of charge replacement of the component that presents a manufacturing defect or material failure. In case of lack of a specific spare part the company reserves the right to replace the tool with another corresponding model. After all warranty procedures have been concluded, the warranty period of the tool shall not be extended or renewed. Replacement of a spare part with repair charge is covered by a 1 year warranty of good operation, subject to compliance with the warranty terms. The spare parts or tools that are replaced remain in the possession of our company. Requirements, other than those mentioned in this warranty form, regarding power tools repair or damage thereof, do not apply. Greek law and relative regulations apply to this warranty.

WARRANTY

This power tool is a quality product. It was designed in compliance with current technical standards and made carefully using normal, good quality materials. The warranty period is 24 months for non-professional use, 12 months for professional use and commences on the date of purchase, which can be verified by the receipt, invoice or delivery note. During this warranty period all functional errors, which, despite the careful treatment described in our operating manual, are verifiably due to material flaws, will be rectified by our after-sales service staff. The warranty takes the form that defective parts will be repaired or replaced with perfect parts free of charge at our discretion. Replaced parts will become our property. Repair work or the replacement of individual parts will not extend the warranty period nor will it result in a new warranty period being commenced for the appliance.

No separate warranty period will commence for spare parts that may beted. We cannot offer a warranty for damage and defects on appliances or their parts caused by the use of excessive force, improper treatment and servicing. This also applies for failures to comply with the operating manual and the installation or spare and accessory parts that are not included in our range of products. In the event of interference with of modifications to the appliance by unauthorized persons, the warranty will be rendered void. Damages that are atributable to improper handling, over loading, or natural wear and tear are excluded from the guarantee. Damages caused by the manufacturer or by a material defect will be corrected at no charge by repair or by providing spare parts. The prerequisite is that the equipment is handed over assembled, and complete with the proof of sale and guarantee.

For a guarantee claim, only use the original packaging. That way, we can guarantee quick and smooth guarantee processing. Please send us the appliances post-paid or request a Freeway sticker. Unfortunately we will be unable to accept appliances that are not postpaid. The warranty does not cover parts that are subject to natural wear and tear. If you wish to make a warranty claim, report faults or order spare parts or accessories, please contact the after-sales center: Subject to change without prior notice.

The instructions manual is also available in digital format on our website www.nikolaoutools.gr. Find it by entering the product code in the Search “ ” field.

WWW.NIKOLAOUTOOLS.GR

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>