InnoTruth S3V2 Baby Safety Gate User Guide

InnoTruth S3V2 Baby Safety Gate

Product Information

Specifications:

• Model No.: S3V2
• Extensions: No Extension, 3.54 inch Extension, 7.09 inch Extension
• Max Size:
  • 28.9 – 31.5 inch
  • 31.5 – 35 inch
  • 35 – 38.6 inch
  • 38.6 – 42.1 inch

Product Usage Instructions

Before Assembly:
Adult assembly is required.

Components:

• A: Gate Frame (x1)
• B: Spindle Rods (x4)
• C: Wall Cups (x4)
• D: Sticker (x4)

1. Step 1: Gate Frame Adjustment

2. Locate the (4) threaded spindle rods (B).

3. Rotate the adjustment wheels along the threading, eliminating the gap between the adjustment wheel and the rubber foot.
   Note: You may notice a slight gap between the gate door latch and the frame. This is not a defect. The gate is pressure mounted and this gap will disappear once you tighten the gate in its opening.

4. Step 2: Gate Installation

5. Insert the threaded spindle rods with adjustment wheels into the hole on all four corners of the sides of the gate.

6. Place the gate in the desired opening with the bottom close to the floor. The distance between the bottom of the gate and the floor should be less than 1/8 inch.
   Note: Once you are satisfied with the placement, trace the spindle rods rubber feet with wall cups onto the surface of your opening and make sure these are level.

7. To affix your gate more firmly, use the screws and stickers provided. Use a pencil to trace the entire outline of each foot onto the wall.
   Note: Remove the gate from the opening and reinforce your gate:

8. Paste the 4 wall cups using the stickers provided.

9. Screw the 4 wall cups to the wall using the screws.

10. Step 3: Gate Tightening

11. Insert all 4 threaded spindle rods into the wall cups.

12. Tighten the wheels by hand. Do not over tighten.

Note: It may be necessary to hold the threaded spindle rods while rotating the adjustment wheels to ensure that the entire unit does not rotate while installing the gate.

Note: If your door latch is not properly engaging with the receiving component, ensure that your gate is level, mounted properly, and that you have not over-tightened the adjustment wheels.

Note: The gap between the gate and the wall should not exceed more than 2.75 inches on either side. If the gate has been installed properly, the gap between the door latch and frame should now be 1/16 inch.

Operating the Door Latch

• To Open: Ensure that the base locks at the bottom of the gate door are in the horizontal position.
• When opening the door, it is necessary to pull back the switch above and lift up the guardrail at the same time.

Note: The baby gate can open 90 degrees in both directions.

Note: Do not put excessive pressure on the gate in order to prevent damage.

FAQ

• Q: How do I choose the right extension for my gate?
  A: Measure the width of your desired opening and refer to the specifications section to determine the appropriate extension size.

• Q: What should I do if my gate is not level or the door latch is not engaging properly?
  A: Ensure that the gate is mounted properly and that you have not over- tightened the adjustment wheels. Adjust the gate as necessary to achieve proper levelness and engagement of the door latch.

• Q: Can the gate be opened in both directions?
  A: Yes, the gate can open 90 degrees in both directions.

KEEP INSTRUCTIONS FOR FUTURE USE.

• READ ALL INSTRUCTIONS BEFORE ASSEMBLY AND USE OF GATE.
• KEEP SMALL PARTS AWAY FROM CHILDREN DURING ASSEMBLY.

WARNING

Children have died or been seriously injured when gates are not securely installed.

• ALWAYS install and use gates as directed using all required parts.
• YOU must install wall cups to keep gate in place. Without wall cups, child can push out and escape.
• STOP using when a child can climb over or dislodge the gate.
• USE only with the locking mechanism securely engaged.
• NEVER use to keep child away from pool.
• NEVER leave child unattended.
• Intended for use with children between 6 and 24 months. • Install according to manufacturer’ s instructions.

EXTENSIONS AND MAX SIZE

Measure the width and choose the right extensions

MODEL NO. S3V2

NO Extension.| 3.54inch Extension| 7.09inch Extension| MAX SIZE
---|---|---|---
28.9 – 31.5inch| 31.5 – 35inch| 35 – 38.6inch| 38.6 – 42.1inch

IMPORTANT

• Improper installation could result in the gate becoming unstable or dislodged from the doorway.
• Base locks are to be used at all times, on both sides of the gate.
• This product will not necessarily prevent all accidents.
• Check the gate regularly to see if all the hardware and mountings are tightened.
• Do not use if any components are missing or damaged.
• Additional or replacement parts should only be obtained from the manufacturer or distributor.

BEFORE ASSEMBLY

Adult assembly required

INSTALLING YOUR GATE

• STEP 1 Locate the (4) threaded spindle rods (B). Rotate the adjustment wheels along the threading, eliminating the gap between the adjustment wheel and the rubber foot (Figure 1-1).
  • NOTE: You may notice a slight gap between the gate door latch and the frame (Figure 1-2).
  • THIS IS NOT A DEFECT this gate is a pressure mounted gate and this gap will disappear once you tighten the gate in its opening.
  • DO NOT REMOVE THE ZIP TIE UNTIL INSTALLATION IS COMPLETE. (Figure 1-3)
• STEP 2 Insert the threaded spindle rods with adjustment wheels into the hole on all four corners of the sides of the gate. (Figure 2-1)
  • Place the gate in desired opening with the bottom close to the floor. The distance between the bottom of the gate and the floor should be less than 1/8 inch (Figure 2-2). Once you are satisfied with the placement, trace the spindle rods rubber feet with wall cups onto the surface of your opening and make sure these are level(Figure 2-3).
  • To affix your gate more firmly, we strongly recommend you to use the screws and stickers provided. Use the pencil to trace the entire outline of each feet onto the wall (Figure 2-4). Remove the gate from the opening and reinforce your gate:

1. Paste the 4 wall cups using the stickers provided (Figure 2-5);
2. Screw the 4 wall cups to the wall using the screws (Figure 2-6).

• STEP 3 Insert all 4 threaded spindle rods into the wall cups (Figure 3-1). Tighten the wheels by hand (Figure 3-2 and Figure 3-3) Do not over tighten. It may be necessary to hold the threaded spindle rods while rotating the adjustment wheels to ensure that the entire unit does not rotate while installing the gate.
  • NOTE: if your door latch is not properly engaging with the receiving component, ensure that your gate is level, mounted properly and that you have not over-tightened the adjustment wheels.
  • NOTE: The gap between the gate and the wall should not exceed more than 2.75 inch on either side (Figure 3-4 and 3-5)
  • If the gate has been installed properly the gap between the door latch and frame should now be 1/16” (Figure 3-6)

OPERATING THE DOOR LATCH

• To Open – Ensure that the base locks at the bottom of the gate door are in the horizontal position (Figure 4-1).
• When opening the door, it is necessary to pull back the switch above and lift up the guardrail at the same time (Figure 4-2 and Figure 4-3).
• The baby gate can open 90 degrees in both directions. (Figure4-4).
• NOTE: Do not put excessive pressure on the gate in order to prevent damage.

USE AT THE TOP OF STAIRS

• If the gate is used at the top of stairs, we recommend the safe distance to the 1st step is at least 16 inch. (Figure A)
• You MUST install wall cups to keep gate in place. Without wall cups, child can push out and escape.

ADDING A GATE EXTENSION

1. STEP 1 Remove the top and bottom threaded spindle rods.(Figure 5-1)
2. STEP 2
3. Assemble the gate and extension as illustrated (Figure 5-2 and 5-3). Reposition the gate and fit in accordance with the gate fitting instructions.
4. NOTE: It is preferable to install any extensions on the hinge side of the gate.

REMOVING YOUR GATE FROM THE WALL
To remove your gate from the wall, rotate the adjustment wheels on each of the (4) threaded spindle rods to depressurize the gate from its doorway or opening. Then, gently pull or push the gate free from its doorway or opening.

CARE AND MAINTENANCE

Periodically check the gate for signs of damage, wear, or missing components. Do not use if any part is missing, worn or damaged. Check the gate regularly to ensure all the hardware and mountings are tightened. Do not use abrasive cleaners or bleach. Clean by sponging with warm water and a mild detergent.

WARRANTY INFORMATION

TWO YEAR NON-TRANSFERABLE LIMITED WARRANTY

• To provide customers with quality shopping and user experience, we guarantee to replace or issue a refund or provide acceptable solution to any defective products (as customers prefer) from the date of purchase to 2 years. Proof of purchase must be provided (Amazon order number or receipt) when making a claim to our customer support center.
• Price matching policy is not applicable.
• No price difference refund.

WHAT IS COVERED

1. Received defective or used (proof needed) products;
2. Received with missing parts;
3. Defective item under proper use.

WHAT IS NOT COVERED

1. Purchased from non-Amazon channel or other physical stores;
2. Gift without proof of purchase;
3. Tampering/abnormal use/accidental damage;
4. Replacements and parts;
5. Installation fee/labor fee

MAKING A CLAIM

If you have any problems when using our products, you can choose any of the methods to reach out to us.

MANUFACTURER SUPPORT:

• 1-888-281-8150(24/7)
• support@aborderproducts.com (24/7)
• 30 Days Free Return & Replacement
• 2-Year Product Warranty

Gifted parts, replacement, consumable products are not covered by the 2-year warranty. Manufacturers’warranties may not apply in all case, depending on factors such as use of the product, where the product was purchased, or who you purchased the product from. Please review the warranty carefully, and contact the manufacturer if you have any questions.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>