InnoTruth VC1910 Safety Gate User Manual

InnoTruth VC1910 Safety Gate

Safety Gate

• KEEP INSTRUCTIONS FOR FUTURE USE.
• READ ALL INSTRUCTIONS BEFORE ASSEMBLY AND USE OF THE GATE.
• KEEP SMALL PARTS AWAY FROM CHILDREN DURING ASSEMBLY.

WARNING

• Children have died or been seriously injured when gates are not securely installed.
• ALWAYS install and use gates as directed using all required parts.
• YOU must install wall cups to keep the gate in place. Without wall cups, children can push out and escape.
• STOP using when a child can climb over or lodge the gate.
• USE only with the locking mechanism securely engaged.
• NEVER use to keep the child away from the pool.
• NEVER leave a child unattended.
• Intended for use with children between 6 and 24 months.
• Install according to the manufacturer’s instructions.

EXTENSIONS AND MAX SIZE

Different sizes need different matching

IMPORTANT

• Improper installation could result in the gate becoming unstable or dislodged from the doorway.
• Base locks are to be used at all times, on both sides of the gate.
• This product will not necessarily prevent all accidents.
• Check the gate regularly to see if all the hardware and mountings are tightened.
• Do not use if any components are missing or dam- aged.
• STOP using when a pet can climb over or dislodge the gate.
• Additional or replacement parts should only be obtained from the manufacturer or distributor.

BEFORE ASSEMBLY

INSTALLING YOUR GATE

• STEP I
  • Locate the (4) threaded spindle rods (B). Rotate the adjustment wheels along the threading, eliminating the gap between the adjustment wheel and the rubber foot (Figure 1-1)
  • NOTE You may notice a slight gap between the gate door latch and the frame (Figure 1-2)
  • THIS IS NOT A DEFECT this gate is a pressure-mounted gate and this gap will disappear once you tighten the gate in its opening.
• STEP 2
  • Insert the threaded spindle rods with adjustment wheels into the hole on all four corners of the sides of the gate.
  • (Figure 2-1) Place the gate in the desired opening with the bottom close to the floor.
  • The distance between the bottom of the gate and the floor should be less than 1/8 inch (Figure 2-2).
  • Once you are satisfied with the placement of your gate trace the spindle rods’ rubber feet onto the surface of your opening making sure these are level (Figure 2-3).
  • Then remove the gate from the opening. Then screw the 4 wall cups to the wall using the screws (Figure 2-4), or paste the 4 wall cups using the stickers provided (Figure 2-5).
• STEP 3
  • Insert all 4 threaded spindle rods into the wall cups (Figure 3-1).
  • Tighten the wheels using the wrench tool. (Figure 3-2 and Figure 3-3) Do not over tighten.
  • It may be necessary to hold the threaded spindle rods while rotating the adjustment wheels to ensure that the entire unit does not rotate while installing the gate.
  • NOTE if your door latch is not properly engaging with the receiving component, ensure that your gate is level, mounted properly and that you have not over-tightened the adjustment wheels.
  • NOTE The gap between the gate and the wall should not exceed more than 2.5 inch on either side (Figure 3-4 and 3-5)
  • Use the supplied wrench to tighten the bolt further until the gap of the latch is 1/16″ wide (roughly the thickness of the supplied wrench) (Figure 3-6)

OPERATING THE DOOR LATCH

• To Open – Ensure that the base locks at the bottom of the gate door are in the horizontal position (Figure 4-1).
  • Pull the spring lock away from the easy open latch while simultaneously lifting the lock lever upwards (Figure 4-2 and 4-3).
  • This will release the locking latch from the gate frame and allow the door to push or pull open.
  • The door can still be opened (one way) if one of the base locks is open (at the horizontal position).
• To Close – Pull the door shut and ensure that the door latch on top closes and then place the lock at the bottom of the gate down on the side occupied by the child, Gate will swing both ways unless one of the swing stops is down.
  • The gate will not swing at all if both swing stops are down. (Figure 4-4)
  • Once the gate is opened, it can close up automatically and lock up.
  • When the opening angle is 300—900, the gate will automatically close (Figure 4-5). When the opening angle is greater than 900, the gate will stay open.(Figure 4-6)

USE AT THE TOP OF STAIRS

• If the gate is used at the top of stairs, we recommend the safe distance to the 1st step is at least 16 inches. (Figure A)
• Using the wall cups will affix your gate more firmly in the doorway or opening.

ADDING A GATE EXTENSION

• STEP 1
  • Remove the top and bottom threaded spindle rods.(Figure 5-1)
• STEP 2
  • Assemble the gate and extension as illustrated (Figure 5-2 and 5-3). Reposition the gate and fit by the gate fitting instructions.
  • NOTE: It is preferable to install any extensions on the hinge side of the gate.

REMOVING YOUR GATE FROM THE WALL

• To remove your gate from the wall, rotate the adjustment wheels on each of the (4) threaded spindle rods to depressurize the gate from its doorway or opening.
• Then, gently pull or push the gate free from its doorway or opening.

CARE AND MAINTENANCE

• Periodically check the gate for signs of damage, wear, or missing components.
• Do not use if any part is missing, worn, or damaged.
• Check the gate regularly to ensure all the hardware and mountings are tightened.
• Do not use abrasive cleaners or bleach. Clean by sponging with warm water and a mild detergent.

WARRANTY INFORMATION

TWO YEAR NON-TRANSFERRABLE LIMITED WARRANTY

• To provide customers with quality shopping and user experience, we guarantee to replace or issue a refund or provide acceptable solutions to any defective products (as customers prefer)from the date of purchase to 2 years).
• Proof of purchase must be provided (Amazon order number or receipt)when claiming our customer support center.
• The warranty is not transferable. We only provide warranty services for buyers purchased from our Amazon store and the recipients possessed the purchase proof,and not any other purchaser or subsequent owner.
• A price matching policy is not applicable for price difference refunds.
• Sellers are the responsible party. Amazon allows different sellers to sell the same product, so please confirm the seller by checking the order details before contacting us.

Manufacturer Support:

• 1-888-281-8150 (24/7)
• support@aborderproducts.com. (24/7)
• 30 Days Free Return & Replacement
• 2-Year Product Warranty

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>