InnoTruth VC1912 Baby Gate for Stairs and Doorways Instruction Manual

Safety Gate

VC1912 Baby Gate for Stairs and Doorways

• KEEP INSTRUCTIONS FOR FUTURE USE.
• READ ALL INSTRUCTIONS BEFORE ASSEMBLY AND USE OF GATE.
• KEEP SMALL PARTS AWAY FROM CHILDREN DURING ASSEMBLY.

WARNING
Children have died or been seriously injured when gates are not securely installed.

• ALWAYS install and use gates as directed using all equired parts.
• YOU must install wall cups to keep gate in place.Without wall cups, child can push out and escape.
• STOP using when a child can climb over or dislodge the gate.
• USE only with the locking mechanism securely engaged.
• NEVER use to keep child away from pool.
• NEVER leave child unattended.
• Intended for use with children between 6 and 24 months.
• Install according to manufacturer’ s instructions.

EXTENSIONS AND MAX SIZE

MODEL NO.| No Extension| 2.75 inch Extension| 5.51 inch Extension| 8.26 inch Extension| MAX SIZE
---|---|---|---|---|---
VC1912| | | | | 37-396inch
VC1913| | | | | 37-396inch
VC1914| | | | | 45-47inch
V1915| | | | | 45-47inch

IMPORTANT

• Improper installation could result in the gate becoming unstable or dislodged from the doorway.
• Base locks are to be used at all times, on both sides of the gate.
• This product will not necessarily prevent all accidents.
• Check the gate regularly to see if all the hardware and mountings are tightened.
• Do not use if any components are missing or damaged.
• STOP using when a pet can climb over or dislodge the gate.
• Additional or replacement parts should only be obtained from the manufacturer or distributor.

BEFORE ASSEMBLY

INSTALLING YOUR GATE

STEP1
Locate the (4) threaded spindle rods (B).
Rotate the adjustment wheels along the threading, eliminating the gap between the adjustment wheel and the rubber foot (Figure 1-1)
NOTE You may notice a slight gap between the gate door latch and the frame (Figure 1-2)
THIS IS NOT A DEFECT this gate is a pressure mounted gate and this gap will disappear once you tighten the gate inits opening.    DO NOT REMOVE THE ZIP TIE UNTIL INSTALLATION IS COMPLETE. (Figure 1-3) STEP2
Insert the threaded spindle rods with adjustment wheels into the hole on all four corners of the sides of the gate. (Figure 2-1) Place the gate in desired opening with the bottom close to the floor. The distance between the bottom of the gate and the floor should be less than 1/8 inch (Figure 2-2).
Once you are satisfied with the placement of your gate trace the spindle rods rubber feet onto the surface of your opening making sure these are level (Figure 2-3). Then remove the gate from the opening. Then screw the 4 wall cups to the wall using the screws (Figure 2-4), or paste the 4 wall cups using the stickers provided (Figure 2-5). STEP3
Insert all 4 threaded spindle rods into the wall cups (Figure 3-1). Tighten the wheels using the wrench tool. (Figure 3-2 and Figure 3-3) Do not over tighten.
It may be necessary to hold the threaded spindle rods while rotating the adjustment wheels to ensure that the entire unit does not rotate while installing the gate.
NOTE if your door latch is not properly engaging with the receiving component, ensure that your gate is level, mounted properly and that you have not over-tightened the adjustment wheels.  NOTE The gap between the gate and the wall should not exceed more than 2.5 inch on either side (Figure 3-4 and 3-5)
Use the supplied wrench to tighten the bolt further until the gap of the latch is 1/16″ wide (roughly the thickness of the supplied wrench) (Figure 3-6)

OPERATING THE DOOR LATCH

To Open – Ensure that the base locks at the bottom of the gate door are in the horizontal position (Figure 4-1). Pull the spring lock away from the easy open latch while simultaneously lifting the lock lever upwards (Figure 4-2 and 4-3). This will release the locking latch from the gate frame and allow the door to push or pull open.
The door can still be opened (one way) if one of the base locks is open (at the horizontal position). ToClose
– Pullthe door shut and ensure that the door latch on top closes and then place the lock at the bottom of the gate down on the side occupied by the child, Gate will swing both ways unless one of the swing stops is down. Gate will not swing atall if both swing stops are down. (Figure 4-4) Once the gate is opened,it can close up automatically and lock up.
When the opening angle is 30°~90°, the gate will automatic closing (Figure 4-5). When the opening angle is greater than 90°, the gate will stay open.(Figure 4-6)

USE AT THE TOP OF STAIRS

If the gate is used at the top of stairs, we recommend the safe distanced to the 1st step is at least 16 inch. (Figure A)
Using the wall cups will affix your gate more firmly in the doorway or opening.

ADDING A GATE EXTENSION

STEP1
Remove the top and bottom threaded spindle rods.(Figure 5-1)
STEP2
Assemble the gate and extension as illustrated (Figure 5-2 and 5-3). Reposition the gate and fit in accordance with the gate fitting instructions.
NOTE: It is preferable to install any extensions on the hinge side of the gate.

REMOVING YOUR GATE FROM THE WALL

To remove your gate from the wall, rotate the adjust- ment wheels on each of the (4) threaded spindle rods to depressurize the gate from its doorway or open- ing. Then, gently pull or push the gate free from its doorway or opening.

CARE AND MAINTENANCE

Periodically check the gate for signs of damage, wear, or missing components. Do not use if any part is missing, worn or damaged. Check the gate regularly to ensure all the hardware and mountings are tight- ened. Do not use abrasive cleaners or bleach. Clean by sponging with warm water and a mild detergent.
TWO YEAR NON-TRANSFERRABLE LIMITED WARRANTY
To provide customers with quality shopping and user experience, we guarantee to replace or issue a refund or provide acceptable solutionsto any defective products (as customers prefer)from the date of purchase to 2 years).
Proof of purchase must be provided (Amazonorder number or receipt)when making a claim to our customer support center.
The warranty is not transferable.We only provide warranty services for buyers purchased from our Amazon store and the recipients possessed the purchase proof,and not any other purchaser or subsequent owner.
Price matching policy is not applicable.No price difference refund.
Sellers are the responsible party. Amazon allows different sellers to sell the same product, so please confirm the seller by checking the order details before contacting us.

Manufacturer Support:
1-888-281-8150 (24/7)
support@aborderproducts.com(24/7)
30 Days Free Return & Replacement
2-Year Product Warranty

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>