SUPERATV RZR Pro R 4 Tinted Hard Top Instruction Manual
- June 3, 2024
- SUPERATV
Table of Contents
2753 Michigan Road · Madison, Indiana 47250 ·
855-743-3427
INSTALLATION INSTRUCTIONS
Roof: for Polaris RZR Pro R 4®
RZR Pro R 4 Tinted Hard Top
- SuperATV does not recommend keeping Roof installed while transporting on an open-air trailer. Remove or secure with straps.
- Do not discard packaging until product has been successfully installed.
Liability Statement
SuperATV’s® products are designed to best fit user’s ATV/UTV under stock
conditions. Adding, modifying, or fabricating any factory or aftermarket parts
will void any warranty provided by SuperATV® and is not recommended.
SuperATV’s® products could interfere with other aftermarket accessories. If
user has aftermarket products on machine, contact SuperATV® to verify that
they will work together.
Although SuperATV® has thousands of satisfied customers, user should be aware
that installing lift kits, long travel, or suspension kits, tires, etc. will
change the ride of machine and may increase maintenance and part wear.
Operating any off-road machine while, or after, consuming alcohol and/or drugs
increases risk of bodily harm or death. No warranty or representation is made
as to this product’s ability to protect user from severe injury or death.
SuperATV® urges operators and occupants to wear a helmet and appropriate
riding gear at all times.
By purchasing and installing SuperATV® products, user agrees that should
damages occur, SuperATV® will not be held responsible for loss of time, use,
labor fees, replacement parts, or freight charges. SuperATV®, nor any 3rd
party, will not be held responsible for any direct, indirect, incidental,
special, or consequential damages that result from any product purchased from
SuperATV®. The total liability of seller to user for all damages, losses, and
causes of action, if any, shall not exceed the total purchase price paid for
the product that gave rise to the claim.
SuperATV® will warranty only parts provided by SuperATV®. Any damage or
problems with OEM housings, bearings, seals, or other manufacturers’ products
will not be covered by SuperATV®. SuperATV® parts and products are not
warrantied if item was not installed properly, misused, or modified.
Installing, adding, modifying, or fabricating any factory or aftermarket
product to your ATV/UTV may violate certain local, state, and federal laws. Be
advised that laws vary depending on town, city, county, state, etc. Use of
certain products on public streets, roads, or highways may be in violation
law. The Buyer is solely and exclusively legally and personally responsible
for any violation of the law by the installation or use of the product. You
must abide by all local, state, and federal laws, including but not limited to
vehicle safety, traffic laws, and ordinances. It is your responsibility to
know the laws and how they apply to you.
The Buyer is responsible to fully understand the capability and limitations of
his/her vehicle according to manufacturer specifications, warnings and
instructions and agrees to hold SuperATV® harmless from any damage resulting
from failure to adhere to such specifications, warnings and/ or instructions.
The Buyer is also responsible to obey all applicable federal, state, and local
laws and ordinances when operating his/her vehicle while using this product,
and the Buyer agrees to hold SuperATV® harmless from any violation thereof.
Roof Cleaning:
- Do not use Rain-X ®, Plexus ®, or any other protector, wax, or polish.
- Do not use window cleaning fluids (Windex, 409, etc) or any solvents (gasoline, denatured alcohol, acetone, etc).
- Never use abrasive cleaners, abrasive pads, or gritty cloths.
1. Thoroughly rinse Roof to float off dirt and mud.
2. Using a soft cloth, or microfiber cloth, clean Roof with warm water and a gentle detergent. Baby shampoo, rubbing alcohol, or hand-washing soap can also be used.
3. To prevent water spots, use a chamois to blot Roof dry.
To ease installation, soak Seal in hot water before cutting or installing to increase flexibility.
-
Install Gasket to ONE side of Bracket.
-
Gasket to run entire length of Bracket.
-
Install Clip Nuts to Cage in locations shown.
-
Repeat for opposite side of Cage.
-
Secure Rear and Front to Bracket with hardware shown; tighten.
-
Gasket side of Bracket to face plastic.
-
Place Roof assembly so that Bracket is showing.
-
Install provided Foam and Seal in locations shown.
-
Place Roof onto machine and secure with hardware shown; tighten.
IN-ROOF-P-PROR4
Need help with your installation?
sales@superatv.com
www.superatv.com
1-855-743-3427
8:00am – 8:00pm EST M-Th 8:00am – 7:00pm EST Friday 9:00am – 2:00pm EST
Saturday
**Read instructions and view illustrations before beginning.
**
IN-ROOF-P-PROR4 1/20/2022
© 2022 SuperATV.com®. All Rights Reserved.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>