DORMAN 924-703 Ignition Lock Cylinder Instruction Manual
- June 1, 2024
- DORMAN
Table of Contents
DORMAN 924-703 Ignition Lock Cylinder
Product Information
Specifications:
- Part Number: 924-703
- Usage: Ignition Lock Cylinder Installation/Removal
- Number of Cut Positions: 8
- Tumblers: 3, self-retaining, located on both sides of the cylinder
Product Usage Instructions
-
Step 1: Remove the Old Cylinder
Follow the shop manual instructions to remove the old cylinder from the steering column. -
Step 2: Locate the Brass Lock Pin
Identify the brass lock pin on the side of the tumbler housing. Note the lock position. -
Step 3: Turn to the Accessory Position
Insert the supplied key and turn the tumbler counter-clockwise to the Accessory position. The key will not be removable in this position. -
Step 4: Unlock Tumbler
Press the brass pin down with a small screwdriver and rotate the tumbler counter-clockwise to unlock it. -
Step 5: Remove Tumbler
The tumbler is now removable from the housing. -
Step 6: Remove Old Cylinder
Using the original key and a small screwdriver, remove the old cylinder from the case to expose the tumblers. -
Step 7: Remove Tumblers
Remove each tumbler one at a time from the old cylinder, noting the identification number and position. -
Step 8: Install New Cylinder
Remove the new cylinder from its case using the new key. Place new tumblers back into the slots in the same order as in the old cylinder.
Note:
Do not reuse old tumblers as worn tumblers can cause lock cylinder failure.
Frequently Asked Questions (FAQ)
-
Q: Can I reuse the old tumblers in the new cylinder?
A: It is recommended to use new tumblers provided in the kit as worn tumblers are a common cause of lock cylinder failure. -
Q: What happens if I do not code the new cylinder to use the original key?
A: If your vehicle uses a key with a microchip and you do not code the new cylinder, the car may start but then shut off immediately as it will not sense the chip.
ATTENTION:
Refer to the appropriate shop manual for your vehicle to obtain specific
service procedures for this part. If you do not have a service manual or lack
the skill to install this part, it is recommended that you seek the services
of a qualified technician. Pay special attention to all cautions and warnings
included in the shop manual. Read and follow all instructions carefully.
REMOVAL/INSTALL OF IGNITION LOCK CYLINDER (924-703)
Chrysler 2007–1998, Dodge 2009–1998, Jeep 2005–1998, Plymouth 2001–1997
General Tech Tip
This lock cylinder must be coded to the original vehicle key if your vehicle uses a key with a microchip or if you wish to retain the original key. If your vehicle uses a key with a microchip and you do not code the new cylinder to use the original key, the car will not sense the chip and will start and then shut right off and will not run.
PLEASE WEAR SAFETY GLASSES!
Instructions
- See the installation video on our website for detailed instructions on coding this lock cylinder to your original key.
- The ignition lock cylinder uses eight cut positions for tumblers. The ignition tumblers (3) are located on both sides of the cylinder (1) and are self-retaining.
INSTALL/REMOVAL INSTRUCTIONS
-
STEP 1:
Remove the old cylinder from the steering column. -
STEP 2:
Locate the brass lock pin on the side of the tumbler housing. Note that there are two (2) pins. One side of the tumbler has a lock position. -
STEP 3:
Insert the supplied key and turn the tumbler counterclockwise to the “Accessory” position. NOTE: the key will not be removable from the lock cylinder when in this position. -
STEP 4:
Using a small screwdriver, press the brass pin down and rotate the tumbler counterclockwise to unlock the tumbler. -
STEP 5: Tumbler is now removable from the housing.
-
STEP 6: Using the original key and a small screwdriver, remove the old cylinder from the case to expose the tumblers. Each of the eight tumblers is stamped with a number 1, 2, 3, or 4. For your original keys to work, they must be replaced in the new cylinder exactly as they were placed in the old cylinder.
-
STEP 7: Remove the tumblers, one at a time from the old cylinder, noting the identification number and its position in the cylinder.
-
STEP 8: Using the new key, remove the new cylinder from its case, and remove the new tumblers from it, taking care not to lose the springs (2). Now place new tumblers back into the slots, in the same order that you recorded when you removed the tumblers from the old cylinder. Use new tumblers, as necessary, with parts provided in the kit. Do not reuse the old tumblers since worn tumblers are the primary cause of lock cylinder failure.
-
STEP 9: When all of the tumblers have been replaced, squeeze them together and insert the old key. Now, reassemble the new cylinder into the new case.
-
STEP 10: Reinstall the new cylinder back into the steering column.
Use when assembling this ignition lock cylinder. View the Installation Video for additional assistance.
We appreciate your opinions regarding this product!
Please call our Technical Assistant with any challenges or suggestions
regarding the installation or operation of this product.
1-800-523-2492.
Disclaimer
Even though every attempt is made to ensure this information is complete and accurate, it is impossible to account for all possible circumstances or situations. Please consult with a qualified auto technician before attempting to perform any work you are not qualified to do. Automobiles can be hazardous to work on; be sure to take all necessary safety precautions. Failure to do so may result in property damage or personal injury. Certain motor vehicle standards and performance requirements may apply to your motor vehicle (such as Federal Motor Vehicle Safety Standards by the National Highway Traffic Safety Administration). Be sure that your work is performed by such standards and that you do not disable any motor vehicle safety features.
©2019 Dorman Products, Inc.
No reproductions in whole or in part without prior written approval.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>