BLANKOM HDC-6008CI DVB-C Headend with Satellite and IPTV Input Instruction Manual

BLANKOM HDC-6008CI DVB-C Headend with Satellite and IPTV Input

 Product Information

satellite transponders
| 128 IPTV inputs (UDP, RTP)
| 4 groups multiplexing + 4 groups scrambling
| 4 adjacent QAM channel modulating
| Excellent RF output performance index, MER 43 dB
| PCR adjusting
| PSI/SI editing and inserting
| Web management, Updates via web
| DiSEqC 1.0 LNB control for up to 4 satellites
| Dual power supply (optional)

Product Usage Instructions

1. Installation Preparation:
   • Check for possible device missing or damage during transportation.
   • Prepare the relevant environment for installation.
   • Install the DVBN-S2 / IP Mux-Scrambling QAM Modulator.
   • Connect signal cables.
   • Connect communication port for WEB-IF.
   • Ensure all cables are properly installed before using the Power-On switch to avoid shortage.
2. Power Cord Connection:
   • Connect the power cord to the device.
3. Grounding Requirement:
   • Connect the device’s grounding rod to the frame’s grounding pole with copper wire.
   • Ensure all function modules have good grounding for reliability, stability, lightning arresting, and interference rejection.
   • Ensure coaxial cables’ outer conductor and isolation layer maintain proper electric conducting with the metal housing of the device.

DVB-C Headend with Satellite and IPTV Input

HDC 6008CI

4 Channel DVB-C (QAM) Headend System 8 DVB-S/S2x tuner inputs for up to 8 FTA and 4 scrambled
satellite transponders 128 IPTV inputs (UDP, RTP) 4 groups multiplexing + 4 groups scrambling 4 adjacent QAM channel modulating Excellent RF output performance index, MER 43 dB PCR adjusting PSI/SI editing and inserting Web management, Updates via web DiSEqC 1.0 LNB control for up to 4 satellites Dual power supply (optional)
BLANKOM HDC-6008CI is a new generation cable-tv headend system in one unit. Satellite and IPTV channels, decrypted, re-encrypted, and
can be combined in a 4 RF- DVB-C group and distributed over coaxial cable to large networks.

The BLANKOM HDC-6008CI is a cost effective SAT- to QAM TransModulator with SAT & IP to DVB-C QAM including multiplexer and descrambling with 4x CICAM slots . Equipped with 8 DVB-S/S2 tuner inputs, 4 CI slots for CAMs, 4 groups multiplexing with scrambling, it supports maximum 128 IPTV inputs via GE port and outputs 4 adjacent carriers (50MHz…960MHz) combined via RF output interface in parallel to 4 MPTS outputs.
HDC-6008CI also features high integration level, high performance and effective cost. Dual power supplies for redundant power supply is optional.
This device is perfect for flexible and/or additional cableTV headend concept.

HDC 6008CI

Technical specifications

Function INPUT OUTPUT
Tuner section
Multiplexing
Scrambling
Modulation
SYSTEM Control Dimensions Power Temperature

4 channel DVB-C Headend with Satellite & IPTV input 8 DVB-S/S2x Tuner (4 of them with CI) 128 IPTV channels over UDP or RTP protocol, Multi- or Unicast 4 DVB-C groups which can be multiplexed from any combination of all input channels, NIT configurable, LCN support 8 DVB-S/S2x tuners with input frequency range: 950-2150 MHz Symbol rate: 0.5…45 MSps (supports SCPC and MCPC) Signal strength: -65…-25dBm Supports QPSK, 8PSK, 16/32 APSK; supports DiSEqC 1.0 LNB control for up to 4 satellites 4 multiplexers, Maximum PID remapping: 128per input channel PID remapping (non, automatically or manually), PCR re-clocking, Generation of PSI/SI table automatically, PID ­ adding manually Max simulscrypt CA: 4 Scramble Standards: ETR289, ETSI 101 197, ETSI 103 197 Local/remote connection 4 DVB-C (QAM) channels, Standard EN300 429/ITU-T J.83A/B RF frequency 50…960 MHz, 1 kHz step RF output level 77…97 dBµV, 0.1 dB step Constellation 16/32/64/128/256QAM MPTS / SPTS over UDP, 10/100 Base-T Ethernet interface (UDP unicast / multicast)
Remote management Web NMS10M/100M 482 × 300 × 44.5mm, 19″ 1RU, 3.7 kg AC 110V±10%,50/60Hz … AC 220V±10%, 50/60Hz, 25 W, (dual power supply optional) 0…45 (operation), -20…80 (storage)

Page – 2 –

BLANKOM-HDC-6008CI_Flyer_EN.docx

HDC 6008CI

BLANKOM-HDC-6008CI_Flyer_EN.docx

HDC 6008CI

Outline

The BLANKOM HDC-6008CI Transmodulator is the 5th generation 8x DVB-S2 Receiver ­ decrypter- Mux-scrambling- modulating and IP-IN/OUT all-in-one device. With 4 multiplexing QAM output channels where every of these can be scrambled with max. 4 simulcrypt Conditional Access Server / CAS and all output as 4x MPTS channels, it supports a maximum of 128 IP input streams through the GbE port and modulate 4 adjacent DVB-C QAM channels (50MHz…960MHz) through the combined RF output. The device is also characterized with high integration level, high performance and a reasonable price.
Application Example

Connection Description

Page – 4 –

BLANKOM-HDC-6008CI_Flyer_EN.docx

HDC 6008CI

Front: Rear left … … … … Rear right

NMS/CAS, RF Out, GbE IPTV I/O data port, opt. USB port Module1: 2x DVB S2 IN, 2x CI Slots (CardA bottom, Card B top), loop Module2: 2x DVB S2 IN, 2x CI Slots (CardC bottom, Card D top), loop Module3: 4x FTA DVB-S2 Tuner Inputs, loop outputs Power switch, Fuse AC IEC Power Socket Grounding

Installation Preparation
When you install the device, please follow the steps below. The details of the installation will be described after this chapter. You can also refer to the rear panel printing during the installation.
The main steps of the installation include:
Checking the possible device missing or damage during the transportation Preparing relevant environment for installation Installing the DVBN-S2 / IP Mux-Scrambling QAM Modulator Connecting signal cables Connecting communication port for WEB-IF Be sure to avoid shortage and all cables are installed properly before use the Power-On switch.
Power cord connection
The power socket is located on the right of rear panel, and the power switch is on the left of front panel. User can plug one end of the power cord to the socket and insert the other end to AC power. When the device solely connects to protective ground, it should adopt independent way, say, share the same ground with other devices. When the device adopts united way, the grounding resistance should be smaller than 1. Caution: Before connecting power cord to the IP QAM Modulator, user should set the power switch to “OFF”.
Grounding Requirement
Connecting the device’s grounding rod to frame’s grounding pole with copper wire. All function modules’ good grounding is the basis of reliability and stability of devices.
Also, they are the most important guarantee of lightning arresting and interference rejection. Therefore, the system must follow this rule. Coaxial cables’ outer conductor and isolation layer should keep proper electric conducting with the metal housing of device.

Page – 5 –

BLANKOM-HDC-6008CI_Flyer_EN.docx

HDC 6008CI
Grounding conductor must adopt copper conductor in order to reduce high frequency impedance, and the grounding wire must be as thick and short as possible.
Users should make sure the 2 ends of grounding wire well electric conducted and be antirust.
It is prohibited to use any other device as part of grounding electric circuit The area of the conduction between grounding wire and device’s frame should be no
less than 25mm2.
Signal and Network Management (NMS) Cable Connection
The signal connections include the connection of input signal cable and the connection of output signal cable. Please use at least CAT 5 STP RJ45 LAN Cable for the management port and CAT 6 DSTP for the streaming data ports to avoid electromagnetic influences. For RF cable we recommend double shielded Coax.
Web NMS Management
This device does not support an LCD operation, and the modification can only be operated with Web NMS by using a standard web-browser. We recommend to use Firefox ­ latest version.
Web-Interface access:
Default IP address = 192.168.0.136 User/pw = admin/admin

Page – 6 –

BLANKOM-HDC-6008CI_Flyer_EN.docx

Setting NTP-Server and Timezone:

HDC 6008CI

And updated:

Local Time/Date settings are important if an own TDT/TOT table should be generated and inserted in
the GENERAL TS-config sub menu for each output ­ if supported. Please assure the reaching of the NTP server IP-Addresses from this unit.

Page – 7 –

BLANKOM-HDC-6008CI_Flyer_EN.docx

Setting up Tuner Inputs
Is easy to understand, just “Edit” every Tuner 1….8:

HDC 6008CI

We assume, that the user is familiar with LNB-Settings, SAT-Transponder settings and polarisations V/H = 13V/18V, High-Low-Band (High-Band 22 KHz=ON) and DiSEqC (Satellite 1…4).
Follow every Input and set according to your needs until all Tuner Inputs have been configured:

Page – 8 –

BLANKOM-HDC-6008CI_Flyer_EN.docx

HDC 6008CI

Transportstream TS Config Menu

For every TS-Output the Input sources can be used and selected.
We recommend to use PID-remapping only if you await collisions from different sources.
CA-Filter usage is only recommended if you have CA-related PID’s after decryption left in your TS which you do not want to pass to the outputs.

Page – 9 –

BLANKOM-HDC-6008CI_Flyer_EN.docx

HDC 6008CI
Parse the Inputs for every single one to extract/read the containing services:

If you like to keep EIT and other addon tables somehow, do not do PID Remapping. CA filter is for deleting unnecessary encryption tables and EMM/ECM PID’s if decryption will be done by CAM’s.
Importing a pre-stored listing is also possible:

Page – 10 –

BLANKOM-HDC-6008CI_Flyer_EN.docx

HDC 6008CI
Setting up incoming IP streams as Input sources works with the usage of the “+”
button:
Use your stream addresses and methods… you can also insert multiple addresses in one shot by using the step counter. Than parse the content:
Remark: The IP Input stream is always only valid for your former selected ouput TS number. Next TS one: You need to import it again or select a different one:

parsing !!!
MPTS or SPTS as Input stream seems to be OK. The only limit will probably be restricted by the GbE Input capacity and the internal stream-processor capacity.

Page – 11 –

BLANKOM-HDC-6008CI_Flyer_EN.docx

HDC 6008CI
Now we have several methods to create the QAM outputs either as pass-through or multiplex mode: In passthrough the NIT which is carried by the SAT-Tuner and maybe be carried by the IP Input as well would also be passed to the output but is probably the wrong one for a CATV network. So this method is not recommended or the input chosen is an IP stream MPTS which doesn’t contain one and the NIT will be passed by another channel for the receivers in the cable network. In MuX mode you can select any pre-configured Inpuits stream from Tuner 1…8 and IP IN and create your individual QAM-TS output. Advantage: You can add single PID’s from the sources but the EIT = EPG Information cannot be created by this device: EIT remultiplexing isn’t supported.
Passthrough:
we use tuner 2 Input as example:

Before we need to know whats all coming in by Stream-Expert from another parallel source using a DekTec Fantasi with the software StreamExpert (we arer selling DekTec if you wish):

Page – 12 –

BLANKOM-HDC-6008CI_Flyer_EN.docx

HDC 6008CI

Page – 13 –

BLANKOM-HDC-6008CI_Flyer_EN.docx

HDC 6008CI

Actually we do no NIT creation at all: That should be done at the end when all QAM channels are ready. But we

like to pass all necessary information from SAT IN to QAM out. To just remark these both Tables has PID-No.:

EIT:

PID 0x0012hex

TDT/TOT:

PID 0x0014hex and can be added to the mux from its source stream later like:

Now, in QAM Mux ­mode CH2 output, the EIT + TDT TOT should be inserted.
We might be able to check this by using the IP stream output:

Page – 14 –

BLANKOM-HDC-6008CI_Flyer_EN.docx

HDC 6008CI

As to bee seen, EIT and TDT/TOT are there. We delete both:

And they are still there. (from the original source)

Page – 15 –

BLANKOM-HDC-6008CI_Flyer_EN.docx

HDC 6008CI
Because we accidently used the passthrough mode and therefore the manual PID adding has no effect. We better change to mux mode:
Check IP-output stream: A lot of things are missing because only related Tables are processed :

Page – 16 –

BLANKOM-HDC-6008CI_Flyer_EN.docx

So again we go into PID-Bypass

HDC 6008CI

Adding the EIT PID number 0x0012 from source input 2.

Yes, that works

We can do this for the SAT-based Time and date + offset tables TDT/TOT 0x0014:

Page – 17 –

BLANKOM-HDC-6008CI_Flyer_EN.docx

HDC 6008CI
BAT and CAT are missing, CAT isn’t that critical because the transponder isn’t crypted at all. All “other” named tables as well- but that is a must have filter when you transmodulate from SAT to DVB-C anyway, because the network is different ­ and so the NIT. In general: TSID, ONID and some private PID’s should be observed and if needed : PID injected. But: The most tables are somehow cross referencing. If you change a SID or remap a PID, the EIT is not valid any more. AIT as well. BAT might also not fully work in the output network. Also adding a TV Service from another source input cannot add it’s data to the existing EIT or other tables. This would be a job for an advanced Remultiplexer-Processor unit which is much more expensive than this Transmodulator. Note: Be carefull for mixing TS ­ SAT In/outs and IP streams: To not overflow the final multiplexed QAM output capacity which practical maximum is around 51 Mb/s ( minus peak-overhead reserve 10…15% recommended) Example:

Page – 18 –

BLANKOM-HDC-6008CI_Flyer_EN.docx

HDC 6008CI
The arrow of OVERFLOW in the right side changes to RED if an overflow is happening. So we try an SD channel to inject here: Remove, than delete the input SPTS and use another:
Add another and parse input content:

Page – 19 –

BLANKOM-HDC-6008CI_Flyer_EN.docx

HDC 6008CI
We might have still some space and insert another ­ considering the bitrate…: Some radios will fit: Even from different input sources:

Page – 20 –

BLANKOM-HDC-6008CI_Flyer_EN.docx

HDC 6008CI
Off course for such a multiplex you can only use the MUX setting in General:

An IPTV Input as MPTS can be passed to the output as well:
Remark: VCT settings are only valid if you use the american DVB-C AnnexB ITU norm.
CI-Card using ­ Decryption by CAM:
After all TS Inputs are configured, the CI ­ Modules inserted can be used for every of the Input streams ­ either from the Tuners or the IP Input Streams:

Page – 21 –

BLANKOM-HDC-6008CI_Flyer_EN.docx

HDC 6008CI

Page – 22 –

BLANKOM-HDC-6008CI_Flyer_EN.docx

Select the Services to be decrypted and Set programm:

HDC 6008CI

SET it and:
Page – 23 –

BLANKOM-HDC-6008CI_Flyer_EN.docx

HDC 6008CI

The log-window displays status and the services and datrates will be shown which are routed now through the CAM.
Modulator settings:
The QAM channels are connected to the 4x IP MPTS output streams. They will contain exactly the same Transportstream we remultiplexed for all of these 4 channels:

Because there bitrates depends from the QAM setups.

Page – 24 –

BLANKOM-HDC-6008CI_Flyer_EN.docx

HDC 6008CI
To change the configuration parameters we can access the Quickly config for all:
where we set start center frequency (other will follow it), the common channel level, DVBC mode (Annex A/C or ITU american AnnexB named), bandwidth, constlleation 64…256 QAM and symbol rate.
Single settings can be accessed individually but becasue we have a common modulator for all and adjacent: the single setting will affect the others:

Page – 25 –

BLANKOM-HDC-6008CI_Flyer_EN.docx

The IPstream settings are more flexible:

HDC 6008CI

NullPkt Filter: The PID 8192dec (0x1FFF hex) can be filtered out -> You would sent a VBR instead of a CBR stream. This safes bandwidth but can cause problems in stupid IP 2 QAM devices in sub headends. UDP or RTP can be chosen:
Scrambled TS (by usage of the Scrambler menu and connection to CASystems) or unscrambled can be chosen to forward as IP out.
Scrambling Menu:

Page – 26 –

BLANKOM-HDC-6008CI_Flyer_EN.docx

HDC 6008CI
4 independent scrambling ­ encryption channels can be designed with up to 4 times simulcrypt:

Single PID’s can be chosen individually to encrypt them.
Which need to be setup in conjunction with the setup of the Network interfaces:

The Device Configuration can be safed,restored, backupped:

Page – 27 –

BLANKOM-HDC-6008CI_Flyer_EN.docx

HDC 6008CI
Firmware upgrades can be installed by this Web ­Interface:
And the Log-files can be sent if probelms occur:

Troubleshooting

Our ISO9001 quality assurance system has been approved by CQC organization. We guarantee the products’ quality, reliability and stability. All of our products have been passed the testing and inspection before shipping out from factory. The testing and inspection scheme already covers all the Optical, Electronic and Mechanical criteria which have been published by us. To prevent potential hazard, please strictly follow the operational conditions.

Page – 28 –

BLANKOM-HDC-6008CI_Flyer_EN.docx

HDC 6008CI

Installation pre-conditions
Installing the device at the place in which environment temperature between 0 to 45 °C Making sure good ventilation for the heat-sink on the rear panel and other heat-sink
bores if necessary Checking the input AC voltage within the power supply working range and the
connection is correct before switching on device Checking the RF output level varies within tolerant range if it is necessary Checking all signal cables have been properly connected Frequently switching on/off device is prohibited; the interval between every switching
on/off must greater than 10 seconds.
Conditions need to unplug power cord
Power cord or socket damaged. Any liquid flowed into device. Any stuff causes circuit short Device in damp environment Device was suffered from physical damage Longtime idle. After switching on and restoring to factory setting, device still cannot work properly. Maintenance needed
Important Notes!
This manual is for use by qualified personnel only. Handling this device or system requires special electronic technical knowledge. To reduce the risk of electrical shock or damage to the equipment, do not perform any servicing other than the installation and operating instructions contained in this manual unless you are qualified to do so. This device operates in the given voltage and frequency range without requiring manual adjustment.
Do not open the top case w/o unplugged power source because serious injury or death may be the result! Inside are components under risk from electrostatic discharge. To avoid equipment damages do not touch these components or, observe the respective handling rules!
For continued protection against fire, the fuses may only be replaced by identical fuses with the same electrical specifications which are designed for the corresponding fuse positions.
No part of this publication may be reproduced in any form or by any means or used to make any derivative work (such as translation, transformation or adaptation) without the written permission from Blankom / IRENIS GmbH.
IRENIS GmbH reserves the right to revise this publication and make changes in its content from time to time, whereby it shall not be obligatory for IRENIS GmbH to provide notification of such revision or change.

Page – 29 –

BLANKOM-HDC-6008CI_Flyer_EN.docx

HDC 6008CI
IRENIS GmbH provides this manual without warranty of any kind, neither implied nor expressed, this includes also any warranties regarding the merchantability and fitness for a particular purpose. IRENIS GmbH may improve this manual or make changes in the products described herein at any point of time.
Installation Notes
All types of the IRENIS-BLANKOM family are 19″devices with 1 RU height designed for installation in 19″ racks. In addition to the front panel screws an internal module support is required at the rack. Depending on the Frontend used and the operating adjustments, the SAT-RF-input ports carrying DC Voltage (13V /18V, max. 400 mA).
By connecting a mains cable, the device can become functional without any auxiliary appliances. The power supply units are designed for the wide range of 100-230V AC; a manual adjustment of the voltage is not necessary.
For some models the second power connector is feeding another independent power supply for internal redundancy. For a maximum of redundancy both power supplies should use different circuits.
All the outputs are decoupled from one another. Thus, the circuit does not have any effect on the functioning of the device. Connections that are not required need not to be terminated.
Suggestion: CAT 6E Ethernet cable for GbEthernet, DSTP (double shielded twisted pair) for the streaming ports
Note:
IPv4 global scope sessions use multicast addresses in the range 224.2.128.0 – 224.2.255.255 with SAP Announcements being sent to 224.2.127.254 Port 9875 (note that 224.2.127.255 is used by the obsolete SAPv0 and MUST NOT be used).
IPv4 administrative scope sessions using administratively scoped IP multicast. The multicast address to be used for announcements is the highest multicast address in the relevant administrative scope zone.
For example, if the scope range is 239.16.32.0 – 239.16.33.255, then 239.16.33.255 is used for SAP Announcements.

Sources:
http://www.etsi.org/deliver/etsi_en/300400_300499/300468/01.15.01_60/en_300468v011501p.pdf
https://www.dvb.org/standards

Page – 30 –

BLANKOM-HDC-6008CI_Flyer_EN.docx

HDC 6008CI

We assume, that the user is familiar with all abbreviations mentioned in this manual.
Contact:
IRENIS GmbH Hauptstr. 29 31171 Nordstemmen- Germany Phone: +49 5069 4809781
IRENIS technical hotline VoIP +49 5069 4399 -860 or -8601 Managing Director: Dipl.Ing. Murad Önol Commercial Register: HRB 206370 / District Court Hildesheim
Web: www.blankom.de E-Mail: info@blankom.de

Page – 31 –

BLANKOM-HDC-6008CI_Flyer_EN.docx

HDC 6008CI

Appendix A Product Disposal

Warning! Ultimate disposal of this product should be handled according to all national laws and regulations.

Warnung Die Entsorgung dieses Produkts sollte gemäß allen Bestimmungen und Gesetzen des Landes erfolgen. ¡Advertencia! Al deshacerse por completo de este producto debe seguir todas las leyes y reglamentos nacionales. Attention La mise au rebut ou le recyclage de ce produit sont généralement soumis à des lois et/ou directives de respect de l’environnement. Renseignez-vous auprès de l’organisme

compétent.
! . Waarschuwing De uiteindelijke verwijdering van dit product dient te geschieden in overeenstemming met alle nationale wetten en reglementen.

Page – 32 –

BLANKOM-HDC-6008CI_Flyer_EN.docx

HDC 6008CI

ANNEX ChannelPlan CATV channel plan:

Bereich Bands

Kanal Channel

Kanalfrequenzen Channel frequency

Mittenfrequenz Middle frequency

Bildträger Picture carrier

Tonträger Sound carrier

Bereich Bands

Kanal Channel

Kanalfrequenzen Channel frequency

Mittenfrequenz Middle frequency

Bildträger Picture carrier

Tonträger Sound carrier

B I
USB Unterer Sonderkanalbereich Midband channels B III
OSB Oberer Sonderkanalbereich Superband channels
ESB Erweiterter Sonderkanalbereich Hyperband channels
…

2 3 4 S 02 S 03 S 04 S 05 S 06 S 07 S 08 S 09 S 10 5 6 7 8 9 10 11 12 S 11 S 12 S 13 S 14 S 15 S 16 S 17 S 18 S 19 S 20 S 21 S 22 S 23 S 24 S 25 S 26 S 27 S 28 S 29 S 30 S 31 S 32 S 33 S 34 S 35 S 36 S 37 S 38 S 39 S 40 S 41

47…54 54…61 61…68 111…118 118…125 125…132 132…139 139…146 146…153 153…160 160…167 167…174 174…181 181…188 188…195 195…202 202…209 209…216 216…223 223…230 230…237 237…244 244…251 251…258 258…265 265…272 272…279 279…286 286…293 293…300 302…310 310…318 318…326 326…334 334…342 342…350 350…358 358…366 366…374 374…382 382…390 390…398 398…406 406…414 414…422 422…430 430…438 438…446 446…454 454…462 462…470

50,50 57,50 64,50 114,50 121,50 128,50 135,50 142,50 149,50 156,50 163,50 170,50 177,50 184,50 191,50 198,50 205,50 212,50 218,50 226,50 233,50 240,50 247,50 254,50 261,50 268,50 275,50 282,50 289,50 296,50 306,00 314,00 322,00 330,00 338,00 346,00 354,00 362,00 370,00 378,00 386,00 394,00 402,00 410,00 418,00 426,00 434,00 442,00 450,00 458,00 466,00

48,25 55,25 62,25 112,25 119,25 126,25 133,25 140,25 147,25 154,25 161,25 168,25 175,25 182,25 189,25 196,25 203 25 210,25 217,25 224,25 231,25 238,25 245,25 252,25 259,25 266,25 273,25 280,25 287,25 294,25 303,25 311,25 319,25 327,25 335,25 343,25 351,25 359,25 367,25 375,25 383,25 391,25 399,25 407,25 415,25 423,25 431,25 439,25 447,25 455,25 463,25

53,75 B IV 60,75 67,75 117,75 124,75 131,75 138,75 145,75 152,75 159,75 166,75 173,75 180,75 187,75 194,75 201,75 208,75 215,75 B V 222,75 229,75 236,75 243,75 250,75 257,75 264,75 271,75 278,75 285,75 292,75 299,75 308,75 316,75 324,75 332,75 340,75 348,75 356,75 364,75 372,75 380,75 388,75 396,75 404,75 412,75 420, 75 428,75 436,75 444,75 452,75 460,75 468,75

2

470…478 474,00 471,25 476,75

2

478…486 482,00 479.25 484,75

2

486…494 490,00 487,25 492,75

2

494…502 498,00 495,25 500,75

2

502…510 506,00 503,25 508,75

2

510…518 514,00 511,25 516,75

2

518…526 522,00 519,25 524,75

2

526…534 530,00 527,25 532,75

2

534…542 538,00 535,25 540,75

3

542…550 546,00 543,25 548,75

3

550…558 554,00 551,25 556,75

3

558…566 562,00 559,25 564,75

3

566…574 570,00 567,25 572,75

3

574…582 578,00 575,25 580,75

3

582…590 586,00 583,25 588,75

3

590…598 594,00 591,25 596,75

3

598…606 602,00 599,25 604,75

3

606…614 610,00 607,25 612,75

3

614…622 618,00 615,25 620,75

4

622…630 626,00 623,25 628,75

4

630…638 634,00 631,25 636,75

4

638…646 642,00 639,25 644,75

4

646…654 650,00 647,25 652,75

4

654…662 658,00 655,25 660,75

4

662…670 666,00 663,25 668,75

4

670…678 674,00 671,26 676,75

4

678…686 682,00 679,25 684,75

4

686…694 690,00 687,25 692,75

4

694…702 698,00 695,25 700,75

5

702…710 706,00 703,25 708,75

5

710…718 714,00 711,25 716,75

5

718…726 722,00 719,25 724,75

5

726…734 730,00 727,25 732,75

5

734…742 738,00 735,25 740,75

5

742…750 746,00 743,25 748,75

5

750…758 754,00 751,25 756,75

5

758…766 762,00 759,25 764,75

5

766…774 770,00 767,25 772,75

5

774…782 778,00 775,25 780,75

6

782…790 786,00 783,25 788,75

6

790…798 794,00 791,25 796,75

6

798…806 802,00 799,25 804,75

6

806…814 810,00 807,25 812,75

6

814…822 818,00 815,25 820,75

6

822…830 826,00 823,25 828,75

6

830…838 834,00 831,25 836,75

6

838…846 842,00 839,25 844,75

6

846…854 850,00 847,25 852,75

6

854…862 858,00 855,25 860,75

Page – 33 –

BLANKOM-HDC-6008CI_Flyer_EN.docx

HDC 6008CI
Elektronische Geräte gehören nicht in den Hausmüll, sondern müssen – gemäß Richtlinie 2002/96/EG DES EUROPÄISCHEN PARLAMENTS UND DES RATES vom 27. Januar 2003 über Elektro- und Elektronik-Altgeräte fachgerecht entsorgt werden. Bitte geben Sie dieses Gerät am Ende seiner Verwendung zur Entsorgung an den dafür vorgesehenen öffentlichen Sammelstellen ab.

Electronic equipment is not household waste – in accordance with directive 2002/96/EC OF THE EUROPEAN PARLIAMENT AND THE COUNCIL dated 27th January 2003 on used electrical and electronic equipment, it must be disposed of properly.
At the end of its service life, take this unit for disposal to an appropriate official collection point
Montage und Sicherheitshinweise / Installation and safety instructions
· Die beschriebenen Geräte dienen ausschließlich der Installation von Satelliten-Empfangsanlagen. · The equipment described is designed solely for the installation of satellite receiver systems. · Jegliche anderweitige Nutzung oder die Nichtbeachtung dieses Anwendungshinweises hat den Verlust
der Gewährleistung bzw. Garantie zur Folge. · Any other use, or failure to comply with these instructions, will result in voiding of warranty cover. · Die Geräte dürfen nur in trockenen Innenräumen montiert werden. Nicht auf oder an leicht
entzündlichen Materialien montieren. · The equipment may only be installed in dry indoor areas. Do not mount on or against highly
combustible materials. · Die Geräte sind mit einer Potenzial-Ausgleichsleitung (Cu, mindestens 4 mm2) zu versehen. · The equipment must be provided with an earthing wire (Cu, at least 4 mm2). · Die Sicherheitsbestimmungen der jeweils aktuellen Normen EN 60728-11 und EN 60065 sind zu
beachten. · The safety regulations set out in the current EN 60728-11 and EN 60065 standards must be
complied with · Verbindungsstecker: HF-Stecker 75 Ohm (Serie F) nach EN 61169-24 · Connector: HF plug 75 Ohm (series F) to EN 61169-24. · Nicht benutzte Teilnehmerausgänge sollten mit 75-Ohm Widerständen (z. B. EMK 03)
abgeschlossen werden. (Verringerung der terrestrischen Signalwelligkeit) · Unused subscriber ports should be closed off by 75 Ohm resistors (e.g. EMK 03). · Nicht benutzte Kaskadenausgänge sind mit 75 Ohm Widerständen inkl. DC- Blocker abzuschließen.
75 Ohm Widerstände ohne Gleichspannungssperren können das Gerät beschädigen! · Unused trunk outputs must be terminated with 75Ohm resistors including DC Blocker. Otherwise the
device may be inoperable or damaged. · Bitte überprüfen Sie die Anlage vor Inbetriebnahme auf evtl. Kurzschlüsse der Koaxial-Kabel. Es ist
darauf zu achten, dass die Eingangspegel der SAT-Ebenen möglichst gleich hoch sind. Power-LEDs zeigen den Betrieb an. Falls die nicht leuchten, bitte die Stromzufuhr kontrollieren. · Please check the installation against shortage in coax cables and connectors before switching on. The input levels should be adjusted accordingly. Power-LED’s showing operational mode. If this is not illuminated, please check the power source. · Stromführendes Gerät · Current- carrying unit · Nicht öffnen oder am Gerät manipulieren! · Do not open or tamper with the unit! · Bei Arbeiten an der Anlage immer die Netzstecker aus der Steckdose ziehen! · When working on the system always unplug the mains plug from the wall socket! · Auf ausreichenden Abstand achten! Nach allen Seiten mind. 5 cm! · Ensure adequate clearance! Min. 5 cm to all sides! · Nicht über Kopf montieren. · Do not install overhead. · Für die Gerätekühlung muß freie Luftzirkulation möglich sein. Überhitzungsgefahr! · Free circulation of air must be possible to discharge the heat emitted by the unit. Risk of overheating!

Page – 34 –

BLANKOM-HDC-6008CI_Flyer_EN.docx

· Zulässige Umgebungstemperatur -20 bis +50°C · Permissible ambient temperature -20 to +50°C
Wir empfehlen die Benutzung von Gleitschienen bevor der BMS im 19 ” Schrank installiert und angeschlossen wird. We recommend using and installing 19” rails in your rack before you mount the BMS and install the F-connectors and cables.

HDC 6008CI

Zur Beachtung / Important notes:
· Auf das Netzgerät dürfen keine mit Flüssigkeit gefüllten Gegenstände gestellt werden. · No liquid-filled items may be placed on top of the power supply unit. · Das Netzgerät darf nicht Tropf- oder Spritzwasser ausgesetzt sein. · The power supply unit must not be exposed to dripping or splashing water. · Der Netzstecker muss ohne Schwierigkeiten zugänglich und benutzbar sein. · The mains plug must be easily accessible and operable. · Das Gerät kann nur durch Ziehen des Netzsteckers vom Netz getrennt werden. · The only reliable method of disconnecting the unit from the mains is to unplug it. · Bei größerem Durchmesser des Kabel- Innenleiters als 1,2 mm bzw. Grat können die Gerätebuchsen
zerstört werden. · If the inner cable conductor diameter is greater than 1.2 mm or in case of burr, the device sockets
may be destroyed.
Please use appropriate measurement equipment when installing and do not use coax length > 50m between Dish-Farm and the Multiswitch to secure signal quality and less slope. Using a handy instrument from i.e. PROMAX or for the cheaper controlling an ALPSAT:

Professional Example Spectrums:

and

Semi-professional

Page – 35 –

BLANKOM-HDC-6008CI_Flyer_EN.docx

HDC 6008CI
Left: C/N measuring. You see the SLOPE = higher attenuation on higher frequencies? Right: Level

Shown is a good quality output level of 80 dBµV directly from a BLANKOM 32 -> 32 -Multiswitch cascaded output. The first 2 showing ASTRA Satellite high band while the 3rd shows Eutelsat Hotbird 13°E on DiSEqC SAT Pos. 2 with a better adjusted LNB at the dish(es). So your signal quality depends on: Dish direction and angles, LNB focus and angle and also its LNB-quality and the cable length and quality.

Page – 36 –

BLANKOM-HDC-6008CI_Flyer_EN.docx

Annex: Table for Conversions of Power @ 75

dBmV

dBµV

dBm 75

mVRMS

8

68

-40.75

2.51

9

69

-39.75

2.82

10

70

-38.75

3.16

11

71

-37.75

3.55

12

72

-36.75

3.98

13

73

-35.75

4.47

14

74

-34.75

5.01

15

75

-33.75

5.62

16

76

-32.75

6.31

17

77

-31.75

7.08

18

78

-30.75

7.94

19

79

-29.75

8.91

20

80

-28.75

10.00

21

81

-27.75

11.22

22

82

-26.75

12.59

23

83

-25.75

14.13

24

84

-24.75

15.85

25

85

-23.75

17.78

26

86

-22.75

19.95

27

87

-21.75

22.39

28

88

-20.75

25.12

29

89

-19.75

28.18

30

90

-18.75

31.62

31

91

-17.75

35.48

32

92

-16.75

39.81

33

93

-15.75

44.67

34

94

-14.75

50.12

35

95

-13.75

56.23

36

96

-12.75

63.10

37

97

-11.75

70.79

38

98

-10.75

79.43

39

99

-9.75

89.13

40

100

-8.75

100.00

41

101

-7.75

112.20

42

102

-6.75

125.89

HDC 6008CI
mW 75 8.4E-05 1.1E-04 1.3E-04 1.7E-04 2.1E-04 2.7E-04 3.3E-04 4.2E-04 5.3E-04 6.7E-04 8.4E-04 1.1E-03 1.3E-03 1.7E-03 2.1E-03 2.7E-03 3.3E-03 4.2E-03 5.3E-03 6.7E-03 8.4E-03 0.011 0.013 0.017 0.021 0.027 0.033 0.042 0.053 0.067 0.084 0.106 0.133 0.168 0.211

Page – 37 –

BLANKOM-HDC-6008CI_Flyer_EN.docx

dBmV 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68

dBµV 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128

dBm 75 -5.75 -4.75 -3.75 -2.75 -1.75 -0.75 0.25 1.25 2.25 3.25 4.25 5.25 6.25 7.25 8.25 9.25 10.25 11.25 12.25 13.25 14.25 15.25 16.25 17.25 18.25 19.25

mVRMS 141.25 158.49 177.83 199.53 223.87 251.19 281.84 316.23 354.81 398.11 446.68 501.19 562.34 630.96 707.95 794.33 891.25 1000.00 1122.02 1258.93 1412.54 1584.89 1778.28 1995.26 2238.72 2511.89

HDC 6008CI
mW 75 0.266 0.335 0.422 0.531 0.668 0.841 1.059 1.333 1.679 2.113 2.660 3.349 4.216 5.308 6.683 8.413 10.591 13.333 16.786 21.132 26.604 33.492 42.164 53.081 66.825 84.128

Page – 38 –

BLANKOM-HDC-6008CI_Flyer_EN.docx

References

• IPTV DVB SMATV CATV Digital Signage Professional Headend Solutions
• IPTV DVB SMATV CATV Digital Signage Professional Headend Solutions
• Specifications - DVB

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>