TRISTAR TR-2561 Hair Trimmer Instruction Manual
- June 9, 2024
- Tristar
Table of Contents
TRISTAR TR-2561 Hair Trimmer
SAFETY Instruction
- By ignoring the safety instructions the manufacturer cannot be held responsible for the damage.
- If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
- Never move the appliance by pulling the cord and make sure the cord cannot become entangled.
- The appliance must be placed on a stable, level surface.
- The user must not leave the device unattended while it is connected to the supply.
- This appliance is only to be used for household purposes and only for the purpose it is made for.
- Animal clipper, hair clipper, and appliances for manicure and pedicure can be used by children aged 3 years under supervision.
- Shaver, wet shaver, animal clipper, hair clipper, and appliances for manicure and pedicure can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
- To protect yourself against an electric shock, do not immerse the cord, plug or appliance in the water or any other liquid.
- Suitable for cleaning under an open water tap.
- Suitable for use in a bath or shower.
- The parts that have to be fixed must be installed so they cannot fall into water.
- This appliance is intended for trimming purposes only.
- WARNING: Detach the hand-held part from the supply cord before cleaning it in water.
- WARNING: Keep the appliance dry.
PARTS DESCRIPTION
- Blades
- Combs 1 to 4
- On/off switch
BEFORE THE FIRST USE
- IMPORTANT : OIL THE BLADES BEFORE THE FIRST USE, AND KEEP OILING THEM AFTER EVERY USE!
- Check the clippers, making sure that they are free of hair and lint. Clean it with the supplied cleaning brush and spread a drop of oil on the blades.
- Use the device only on dry hair.
USE
- The following table provides which comb you need to cut the desired lengths.
- To put the comb down, hold the comb with teeth up and push the comb firmly against the blade side.
- Comb 1 — leaves hair approx. 0.3 cm. in length.
- Comb 2 — leaves hair approx. 0.6 cm. in length.
- Comb 3 — leaves hair approx. 0.9 cm. in length.
- Comb 4 — leaves hair approx. 1.2 cm. in length.
- At the beginning, cut only a small amount of hair until you become accustomed to the length. Each comb leaves the hair. It is suggested to try the longest comb 10.4 on the clipper first, then use a another comb if the desired length is shorter. For uniform cutting, never push or force the clipper through the hair at a fast rate.
- Start by combing the hair in its natural direction, place the largest, attachment comb onto the clipper and start by trimming the sides from the bottom upwards. Hold the clipper lightly against the hair with teeth of the attachment comb pointing up.
- Slowly lift the clipper up and outward through the hair, cutting only a small amount at a time. Repeat around sides and back of head.
Use blade lever
- The blade lever allows you to gradually change the closeness of your cut without an attachment comb. When the lever is in the uppermost position, the blades will give you the closest cut and leave the hair very short. Pushing the lever downward gradually increases the cutting length. In its lowest position, the lever will leave the hair approximately the same
- Always remove the plug from the outlet first. After each use, remove any hair with the cleaning brush and spread one or two drops of oil on the blades. Use only acid-free oil as supplied. Unscrew the blades regularly and remove all hair trimmings. When replacing the blades make sure that they are properly adjusted. The blades are adjusted as follows:
- Screw the blades back on the clippers, but do not turn the screws tightly yet.
- Turn the blade lever to the side downward.
- Shift the top blade until it is even (parallel) with the bottom blade and be sure that the two blades are about 1.2mm (1/32 inch) apart.
- Now tighten screws firmly and make sure that the blades cannot shift.
- Clean the outside of the clipper with a clean soft, damp cloth. Never immerce the device in water or other liquid.Do not place or store appliance where it can fall or be pulled into a tub or sink.
CLEANING AND MAINTENANCE
Always remove the plug from the outlet first. After each use, remove any hair with the cleaning brush and spread one or two drops of oil on the blades. Use only acid-free oil as supplied. Unscrew the blades regularly and remove all hair trimmings. When replacing the blades make sure that they are properly adjusted. The blades are adjusted as follows:
- Screw the blades back on the clippers, but do not turn the screws tightly yet.
- Turn the blade lever to the side downward.
- Shift the top blade until it is even (parallel) with the bottom blade and be sure that the two blades are about 1.2mm (1/32 inch) apart.
- Now tighten screws firmly and make sure that the blades cannot shift.
- Clean the outside of the clipper with a clean soft, damp cloth. Never immerce the device in water or other liquid.Do not place or store appliance where it can fall or be pulled into a tub or sink.
ENVIRONMENT
This appliance should not be put into the domestic garbage at the end of its durability, but must be offered at a central point for the recycling of electric and electronic domestic appliances. This symbol on the appliance, instruction manual and packaging puts your attention to this important issue. The materials used in this appliance can be recycled. By recycling of used domestic appliances you contribute an important push to the protection of our environment. Ask your local authorities for information regarding the point of recollection.
Support
You can find all available information and spare parts at www.tristar.eu!
WWW.TRISTAR.EU
Tristar Europe B.V.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>