DORMAN 740-736 Front Passenger Side Power Window Regulator Regulator Only Installation Guide

DORMAN 740-736 Front Passenger Side Power Window Regulator Regulator Only

Product Information

Specifications

• Product Name: Window Regulator
• Model Number: 740-736
• Tools Required: Phillips screwdriver, non-marring pry tool
• Additional Equipment: Safety glasses, silicone spray

Product Usage Instructions

Removal Instructions

1. STEP 1: Using a Phillips screwdriver, remove the screw in the door handle cup and the screw behind the upper inner door handle.
2. STEP 2: Use a non-marring pry tool to remove the inner door handle cup and window switch. Unplug the window switch harness and set the assembly aside.
3. STEP 3: Gently use a non-marring pry tool to remove the inner door handle around the lock. Remove the lock switch harness plug and set the assembly aside.

Frequently Asked Questions (FAQ)

• Q: Do I need any special tools to install the window regulator?
  A: Yes, you will need a Phillips screwdriver and a non-marring pry tool for the installation process.

• Q: Can I install the window regulator myself if I don’t have experience?
  A: It is recommended that you seek the services of a qualified technician if you lack the skill to install this part.

ATTENTION : Refer to the appropriate shop manual for your vehicle to obtain specifi c service procedures for this part. If you do not have a service manual or lack the skill to install this part, it is recommended that you seek the services of a qualifi ed technician. Pay special attention to all cautions and warnings included in the shop manual. Read and follow all instructions carefully.

General Tech Tips:

• Use painter’s tape rather than duct tape to secure window. It’s less likely to damage paint or leave sticky residue.
• A plastic pry tool is useful. It will not easily damage delicate trim like a screwdriver or metal pry bar.
• The replacement regulator should have a liberal amount of grease on slide area. If there is not much grease present, white lithium grease works well to lubricate the slide area.
• Aftermarket window tinting can cause the window to travel slower and put additional strain on the window regulator assembly.
• Window run channels should be cleaned and lubricated before installation of a new window regulator assembly. Silicone spray works well.

Tools required for removal and installation of window regulator and motor assembly:

• Silicone spray lubricant
• Trim panel removal tool
• Pick
• Saddle cup assembly, tape, or wedge to hold window in place
• Flat-blade screwdriver or plastic pry tool
• 10mm socket or driver
• Phillips screwdriver
• Grease pencil or marker

Optional:

• Door panel install kit (Dorman pn# 702-007)

PLEASE WEAR SAFETY GLASSES!

Removal Instructions

1. STEP 1: Using your Phillips screwdriver, remove the screw located in the door handle  cup. Then, remove the Phillips head screw located behind the upper inner door handle.
2. STEP 2: Using your non-marring pry tool, remove the inner door handle cup and window switch. Then, unplug the window switch harness and set the assembly to the side.
3. STEP 3: Take your non-marring pry tool and gently remove the inner door handle that sits around the lock. Once you have removed it, remove the lock switch harness plug. Set the assembly to the side.
4. STEP 4: Remove the speaker cover using your non marring pry tool. Use your Phillips screwdriver to remove the 3 outer screws.
5. STEP 5: Using your non marring pry tool, pry the corner of the door panel off . Work your way around the door panel to release the panel clips.
6. STEP 6: Pull the panel off of the inner door skin.
7. STEP 7: Remove the speaker wire harness clip and set the door panel aside.
8. STEP 8: Using your Phillips screwdriver, remove the door panel bracket and set it aside.
9. STEP 9: Remove the vapor barrier from the inner door skin. Make sure to feed the wiring harness through the holes in the vapor barrier. You may need to pull some harness clips from the inner door skin.
10. STEP 10: Plug the window switch back in and make sure the window mount bolts are accessible through the door skin.
11. STEP 11: Disconnect the motor harness plug from the main door harness.
12. STEP 12: Unbolt the glass mounts from the regulator using a 10mm socket.
13. STEP 13: Remove the two 10mm regulator mount bolts. Pull the glass up to its highest position and secure the glass using a wedge.
14. STEP 14: Remove the four (4) 10mm motor mount bolts that run through the inner door skin.
15. STEP 15: Remove the regulator from the large hole in the inner door skin.
16. STEP 16: Remove the window lift motor attaching screws, to separate the motor from the regulator

Installation Instructions

1. STEP 1: Using the window lift motor attaching screws, attach the motor to the new regulator. Then, feed the regulator assembly through the large hole in the inner door skin.
2. STEP 2: Insert the motor mounting bolts and tighten with a 10mm socket.
3. STEP 3: Plug any harness plugs or wires back into the inner door skin.
4. STEP 4: Reinstall the regulator assembly bolts to the inner door skin.
5. STEP 5: Take out the glass wedge and start the 10mm bolts into the glass mounts. Then slip them on the regulator. Once set, tighten the 10mm bolts.
6. STEP 6: Plug the window switch back in and test the assembly. If everything is working properly, unplug the switch and set it aside.
7. STEP 7: Lay the vapor barrier back onto the inner door skin.
8. STEP 8: Reinstall the door panel brace using your Phillips screwdriver
9. STEP 9: Plug the speaker harness back into the speaker. Test for proper connection.
10. STEP 10: Reinstall the door panel and make sure to feed any harnesses through the proper holes in the panel. Take careto reinstall any factory options you might have on the vehicle like tweeters  or power mirror harnesses.
11. STEP 11: Reinstall the window switch and set it back into the door panel. Use your Phillips screwdriver to secure the door handle cup with the screw.
12. STEP 12: Install the three (3) screws you removed from the door panel around the speaker.
13. STEP 13: Install the door handle, taking care to plug back in the door lock harness plug.  Use your Phillips screwdriver to reinstall the screw you removed.
14. STEP 14: Verify that all of the interior door trim panel attaching hardware is secure and that the window regulator is operating properly.

We appreciate your opinions regarding this product!
Please call our Technical Assistant with any challenges or suggestions regarding the installation or operation of this product.
1-800-523-2492

Disclaimer:
Even though every attempt is made to ensure this information is complete and accurate, it is impossible to account for all possible circumstances or situations. Please consult with a qualified auto technician before attempting to perform any work you are not qualified to do. Automobiles can be hazardous to work on; be sure to take all necessary safety precautions. Failure to do so may result in property damage or personal injury. Certain motor vehicle standards and performance requirements may apply to your motor vehicle (such as Federal Motor Vehicle Safety Standards by the National Highway Traffic Safety Administration). Be sure that your work is performed by such standards and that you do not disable any motor vehicle safety features.
ATTENTION : Refer to the appropriate shop manual for your vehicle to obtain specific service procedures for this part. If you do not have a service manual or lack the skill to install this part, it is recommended that you seek the services of a qualified technician. Pay special attention to all cautions and warnings included in the shop manual. Read and follow all instructions carefully.
©2013 Dorman Products, Inc. No reproductions in whole or in part without prior written approval.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>