Dorman 742-124 Power Window Motor Instruction Manual
- June 1, 2024
- DORMAN
Table of Contents
Dorman 742-124 Power Window Motor
Product Information
Specifications:
- Product Model: 742-124
- Product Name: Window Lift Motor
- Tools Required: 10mm socket, ratchet assembly, trim panel removal tool, T-30 Torx bit, pick or small flat-blade screwdriver
- Additional Requirement: Silicone spray
- Safety Gear: Safety glasses
Product Usage Instructions
Removal Instructions:
- Using a pick or small flat-blade screwdriver, remove the interior door pull retaining screw cover plate.
- Using a 10mm socket and ratchet assembly, remove the two (2) interior door pull retaining screws.
- Using a trim panel removal tool, remove the interior door trim panel assembly. Place the tool between the panel and the door, then pry towards you to release the retaining clips.
- Disconnect the power switch assembly.
- Remove the interior door trim panel.
- Remove the water vapor barrier.
- Using a T-30 Torx bit and ratchet assembly, remove the Torx bit retaining the interior door trim panel support bracket.
- Temporarily connect the power switch assembly and lower the door glass to expose the screws attaching the window regulator to the door glass.
- Using a 10mm socket and ratchet assembly, remove the four (4) interior door trim panel support bracket retaining screws. Note: These screws also hold the window regulator in place.
Frequently Asked Questions
- Q: Can I install the window lift motor myself?
- A: It is recommended to refer to the appropriate shop manual for specific service procedures. If you lack the skill, it’s best to seek the services of a qualified technician.
- Q: What tools are required for removal and installation?
- A: Tools required include a 10mm socket, ratchet assembly, trim panel removal tool, T-30 Torx bit, and a pick or small flat-blade screwdriver. Safety glasses are also necessary.
- Q: Do I need any additional products for assembly?
- A: Silicone spray is recommended for smooth assembly.
ATTENTION: Refer to the appropriate shop manual for your vehicle to obtain specific service procedures for this part. If you do not have \a service manual or lack the skill to install this part, it is recommended that you seek the services of a qualified technician. Pay special attention to all cautions and warnings included in the shop manual. Read and follow all instructions carefully
General Tech Tips
- Use painter’s tape rather than duct tape to secure the window. It will not damage paint or leave sticky residue.
- A plastic pry tool is useful. It will not easily damage delicate trim like a screwdriver or metal pry bar.
- The replacement regulator should have a liberal amount of grease on slide area. If there is not much grease present, white lithium grease works well to lubricate the slide area.
- Aftermarket window tinting can cause the window to travel slower and put additional strain on the window regulator assembly.
- Window run channels should be cleaned and lubricated before installation of a new window regulator assembly. Silicone spray works well.
PLEASE WEAR SAFETY GLASSES!
Tools required
Tools required for removal and installation of a window regulator and motor assembly:
- Silicone spray lubricant
- Trim panel removal tool
- Pick
- Saddle cup assembly, tape, or wedge to hold window in place
- Flat-blade screwdriver or plastic pry tool
- 10mm socket or driver
- Phillips screwdriver
- Grease pencil or marker
- T-30 Torx bit
Disclaimer:
Even though every attempt is made to ensure this information is complete and accurate, it is impossible to account for all possible circumstances or situations. Please consult with a qualifi ed auto technician before attempting to perform any work you are not qualifi ed to do. Automobiles can be hazardous to work on; be sure to take all necessary safety precautions. Failure to do so may result in property damage or personal injury. Certain motor vehicle standards and performance requirements may apply to your motor vehicle (such as Federal Motor Vehicle Safety Standards by the National Highway Traffi c Safety Administration). Be sure that your work is performed in accordance with such standards and that you do not disable any motor vehicle safety feature.
Removal Instructions
- STEP 1: Using a pick or small flat-blade screwdriver, remove the interior door pull retaining screw cover plate.
- STEP 2: Using a 10mm socket and ratchet assembly, remove the two (2) interior door pull retaining screws.
- STEP 3: Using a trim panel removal tool, remove the interior door trim panel assembly. NOTE: Place the trim panel removal tool between the interior door trim panel and the door. Pry the tool toward you to release the interior door trim panel retaining clips.
- STEP 4: Disconnect the power switch assembly
- STEP 5: Remove the interior door trim panel
- STEP 6: Remove the water vapor barrier.
- STEP 7: Using a T-30 Torx bit and ratchet assembly, remove the Torx bit retaining the interior door trim panel support bracket
- STEP 8: Temporarily connect the power switch assembly and lower the door glass, exposing the screws attaching the window regulator to the door glass
- STEP 9: Using a 10 mm socket and ratchet assembly, remove the four (4) interior door trim panel support bracket retaining screws. NOTE: The four (4) interior door trim panel support bracket retaining screws also hold the window regulator in place.
- STEP 10: Disconnect the power switch assembly.
- STEP 10a: Using a 10mm socket and ratchet assembly, remove the two (2) screws attaching the window regulator to the door glass.
- STEP 11: Once the door glass has been separated from the window regulator, manually slide the door glass into the closed position and hold in place with either a saddle cup assembly, painter’s tape, or a wedge.
- STEP 12: Disconnect the window lift motor connector.
- STEP 13: Using a 10 mm socket and ratchet assembly, remove the three (3) window lift motor retaining screws.
- STEP 14: Remove the window regulator through the main access hole. NOTE: You may need to remove the Styrofoam noise insulator from the door
- STEP 15: Using a 10mm socket and ratchet assembly, or a T-30 Torx bit, remove the three (3) window lift motor retaining screws.
Installation Instructions
- STEP 1: Using a 10mm socket and ratchet assembly, or a T-30 Torx bit, attach the three (3) window lift motor retaining screws to the window regulator.
- STEP 1a: Install the window regulator through the main access hole.
- STEP 2: Using a 10 mm socket and ratchet assembly, attach the four (4) window regulator/interior door trim panel support bracket retaining screws.
- STEP 3: Using a 10mm socket and ratchet assembly, attach the three (3) window lift motor attaching screws.
- STEP 4: Connect the window lift motor connector.
- STEP 5: Temporarily connect the power switch assembly to raise or lower the window regulator, aligning the points mounting the door glass to the window regulator.
- STEP 6: Manually slide the door glass into position, aligning the points attaching the door glass to the window regulator.
- STEP 6a: Using a 10mm socket and ratchet assembly, attach the door glass to the window regulator. NOTE: If you did not remove the Styrofoam noise insulator please go to Step 8.
- STEP 7: Install the Styrofoam noise insulator
- STEP 8: Attach the water vapor barrier.
- STEP 9: Connect the power switch assembly connector.
- STEP 10: Install the interior door trim panel assembly. NOTE: Be sure to align all of the interior door trim panel retainers. Failure to do so may result in damage to the interior door trim panel or the interior door trim panel retaining clips.
- STEP 11: Using a 10 mm socket and ratchet assembly, attach the two (2) interior door pull retaining screws
- STEP 12: Install the interior door pull retaining screw cover plate
- STEP 13: Verify that the interior door trim panel is secured and that the window regulator is operating properly
We appreciate your opinions regarding this product! Please call our Technical Assistant with any challenges or suggestions regarding the installation or operation of this product. 1-800-523-2492
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>